Pulsar AS 200 - Motorcycle Bajaj - Free user manual and instructions
Find the device manual for free Pulsar AS 200 Bajaj in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of Product | Motorcycle |
| Brand | Bajaj |
| Model | Pulsar AS 200 |
| Category | Street bike / Naked |
| Engine Displacement | 199.6 cc |
| Engine Type | Single cylinder, 4-stroke, DTS-i |
| Max Power | 19.5 PS @ 8500 rpm |
| Max Torque | 18.3 Nm @ 6500 rpm |
| Transmission | 6-speed constant mesh |
| Fuel System | Carburetor / Electronic Fuel Injection (depending on variant) |
| Cooling System | Oil-cooled |
| Starting Method | Electric start |
| Fuel Tank Capacity | 12 L (approx.) |
| Ground Clearance | 168 mm |
| Seat Height | 800 mm |
| Kerb Weight | 152 kg |
| Front Brake | 280 mm Disc |
| Rear Brake | 230 mm Disc |
| Front Suspension | Telescopic fork, 130 mm travel |
| Rear Suspension | Monoshock, 110 mm travel |
| Front Tyre | 100/80-17 |
| Rear Tyre | 130/70-17 |
| Maintenance Interval | Every 6000 km or 6 months |
| Battery | 12V, 7 Ah (MF) |
Frequently Asked Questions - Pulsar AS 200 Bajaj
What type of fuel should I use for the Bajaj Pulsar AS 200?
Use unleaded petrol with a minimum octane rating of 91 RON. Avoid using E10 ethanol blends above 10%.
How often should I change the engine oil?
Change the engine oil every 6000 km or 6 months, whichever comes first. Use recommended 20W50 grade oil.
What is the recommended tyre pressure?
Front tyre: 28 psi (1.93 bar), Rear tyre: 32 psi (2.21 bar) for solo riding. Adjust for pillion or loads.
How do I adjust the chain slack?
Loosen the rear axle nut, adjust both chain adjusters evenly to achieve 20-30 mm of vertical movement, then retighten the axle nut to 50 Nm torque.
What is the proper break-in procedure for a new engine?
For the first 1000 km, avoid full throttle, vary engine speeds, and do not exceed 4000 rpm for the first 500 km and 5000 rpm thereafter.
How to clean and maintain the air filter?
Remove the air filter element every 6000 km. Clean with compressed air from inside out. Replace if damaged or after 12,000 km.
Why does my Pulsar AS 200 overheat?
Common causes include low engine oil, coolant level (if equipped), clogged radiator or faulty thermostat. Check and top up fluids, clean radiator fins.
What spark plug gap should I use?
Use NGK CR8E or equivalent. Set gap to 0.7-0.8 mm (0.028-0.031 in). Torque spark plug to 12-15 Nm.
How to replace the headlight bulb?
Access the bulb from behind the headlight assembly. Disconnect wiring, remove retaining clip, and replace with an H4 55/60W bulb. Avoid touching the glass.
Where is the VIN number located?
The VIN is stamped on the right side of the steering head and also on the engine crankcase. It is 17 characters long.
User questions about Pulsar AS 200 Bajaj
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motorcycle in PDF format for free! Find your manual Pulsar AS 200 - Bajaj and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Pulsar AS 200 by Bajaj.