Wireless Camcorder - Camcorder ROLLEI - Free user manual and instructions

Brand	Rollei
Model	Wireless Camcorder
Product Type	Camcorder
Power Supply	Built-in rechargeable battery, charging via micro USB (5V) or included power adapter (EU/UK plug)
Battery Charging Indicator	Red flashing during charging, off when fully charged
Low Battery Warning	Red flashing every 5 seconds
Storage	Micro SD card slot (card not included)
Connectivity	Wi-Fi (802.11 b/g/n), micro USB 2.0
Recording Modes	Video, Photo, Loop Recording
Wireless Modes	Direct Mode (local Wi-Fi direct to mobile/PC) and Cloud Mode (via access point or hotspot to USTREAM)
Remote Control	Via Unieye mobile app (iOS/Android) or PC app
Live View	Yes, via app or USTREAM website
Two-Way Audio	Yes, tap to talk and listen
Quad View	Supports up to 4 cameras
Image Inversion	Yes, for inverted mounting
Mounting Accessories	Clip mount, magnet mount, strap mount, tripod mount (1/4 inch)
Waterproof Housing	Included, depth rating not specified
PC Application	PC APP installed from camera storage, features similar to mobile app
Cloud Service	USTREAM (free account required)
Auto Power Off	After 5 minutes of idle
Forced Shutdown	Press and hold Power button for 5 seconds
Factory Reset	Press and hold Mode and Record buttons for 5 seconds

Frequently Asked Questions - Wireless Camcorder ROLLEI

How do I charge the Rollei Wireless Camcorder?

Use the included power adapter or connect via USB to your computer. During charging, the status indicator flashes red and turns off when fully charged.

How do I connect to the camera in Direct Mode?

Set the camera to Direct Mode (press Mode button until indicator shows steady green). On your mobile, go to Wi-Fi settings, connect to the camera's network (no password initially), then open the Unieye app.

What is the Cloud Mode and how do I set it up?

Cloud Mode allows you to view live video remotely via the internet. First, connect the camera to a Wi-Fi access point using the Unieye app (Setup > Cloud Settings > Cloud AP). Then configure a USTREAM account in the app. Finally, switch the camera to Cloud Mode; the indicator will flash orange then turn green when connected.

What should I do if I forgot the camera's Wi-Fi password?

Press and hold both the Mode and Record buttons for 5 seconds to reset the camera to factory default settings. The password will be cleared.

How do I use the waterproof housing?

Slide the OPEN switch to the right and lift the latch arm. Place the camera inside so the Record button aligns with the housing's spring button. Hook the hinged arm onto the backdoor, then push down the latch arm to secure.

Why is the camera not recording?

Ensure a micro SD card is inserted and not full. The card must be formatted; you can format it in the Unieye app. If the card is not recognized, try a different one.

How can I view live video on my PC?

Install the PC APP from the camera's internal storage (connect via USB, autorun should appear). Once installed, run the app and connect to the camera in Direct Mode. You can also view via USTREAM website if using Cloud Mode.

What does the status indicator mean?

Recording: flashing green. Loop recording: flashing orange. Charging: flashing red (off when full). Low battery: flashing red every 5 seconds. Cloud connection successful: steady green. Errors: flashing red with beeps (see manual for specific codes).

Can I use the camera as a webcam?

Yes. Connect the camera to your PC via USB, then press the Mode button to switch to Webcam Mode (indicator turns steady green). In Skype or QQ, select 'UVC_WEBCAM' as the camera.

How do I enable loop recording?

Press and hold the Record button for 3 seconds. The camera will start recording in 3-minute intervals (flashing orange indicator). Press the Record button again to stop.

USER MANUAL Wireless Camcorder ROLLEI

Exterior view of a gray digital camera with lens and control buttons (no visible text or symbols)

Names of Parts

Gray rectangular object with a curved top and two stacked blocks at the base (no visible text or symbols)

Gray rectangular object with a small protrusion at the base (no visible text or symbols)

Clip Mount Magnet Mount
Strap Mount

Getting Started

Charging the Unit

- Before initial use, fully charge the camera via the attached power adapter or on your computer via USB.

Note: The plug of the power adapter could be switched (European or UK Plug)

- During charging, the status indicator flashes red. When the camera is fully charged the indicator turns off.

Diagram of a mechanical device with a downward arrow indicating force or direction (no text or symbols)

Modes Navigation

- Press Power button to turn on camera.

- Press Mode button to switch among Video-Direct Mode, Photo-Direct Mode, and Cloud Mode.

Camera Modes

Insert micro SD card (sold separately).

Video Mode

- Press Mode button to select Video Mode.

- Press Record button to shoot and press again to stop.

Photo Mode

- Press Mode button to select Photo Mode.

- Press Record button to take pictures.

Wireless Modes

Before using wireless modes, install below applications:

- Mobile app: Download [Unieye] from Google Play or Apple Store.

• PC software: Install [PC APP] from camera (Windows)(page 6).

Direct Mode

Connecting camera to mobile or PC directly for remote controlling, live viewing, album managing, and camera setup.

Cloud Mode

Connecting camera to cloud server via access point (AP) or mobile hotspot for internet video or live monitoring.

(i) Direct Mode (Local)

For initial use, install [Unieye] app on mobile. Each camera has a unique Camera ID. ( U2-xxxxxxxxx)

Password is not required for the initial use, however, it is advised to go to [Setup] in app to setup password after connected.

Connect to Camera For iOS user:

• Set camera to Direct Mode
• On mobile, go to [Settings] [Wi-Fi] Choose a camera.
  3G connection will switch to WiFi within 1 min.
• Run [Unieye].
• Press camera bar to start.

For Android user:

• Set camera to Direct Mode (+) and wait until indicator turns steady green.
• On mobile, activate WiFi.
• Run [Unieye].
• Press camera bar to start.

graph TD
    A["iOS: Wi-Fi"] --> B["Unieye"]
    B --> C["Android: Unieye"]
    C --> D["View: U2-0000001"]
    C --> E["Android: CURRENT_AP"]

	Zoom In		Zoom out		Take Photo(SD card required)		Shoot Video(SD card required)
	Invert Image					Loop RecordingRecord and archive in 3 min interval
	Two Way VoiceTap to talk to the camera from mobile; tap again to allow the camera to talk back to mobile.					Quad ViewPress to enable Quad View (up to four cameras).Tap [1] button to return to single view.

Note:1. Move the camera further away from mobile when echo occurs.

1. Mobiles with low CPU clock speed may not have audio during streaming.

graph TD
    A["Central Device"] --> B["Cloud AP"]
    A --> C["Mobile Hotspot"]
    B --> D["3G/4G"]
    C --> D
    D --> E["USTREAM"]
    E --> F["Cloud Server"]
    F --> G["Mobile / PC"]
    F --> H["Laptop"]

Recommended Cloud Server for Access:

USTREAM A live broadcasting social media.

Before using Cloud Mode, it is required to set up cloud AP and cloud server on camera in Direct Mode: follow Step 1 \~ Step 4.

Step 1: Setup Cloud AP

On mobile, start the app and go to [Setup] [Cloud Settings]

[Cloud AP]. Select a WiFi network from [AP List]; enter network password when prompted.

If no preferred AP is found, press [Other...] from [AP List] Enter network name and password.

Note: Mobile hotspot can be set as cloud AP.

Step 2: Setup Cloud Server

• New user, press then enter email/username/password/confirm for auto-registration. Returning user, enter username/password only.
• Press [Save to Camera].

Step 3: Connect Camera to Cloud Server

• To connect to cloud server, choose one of the following:

1. In the app [Setup] page, press [Camera to Cloud].

2. Exit the app. On camera, press the Mode button to switch to Cloud Mode 🔒.

3. While connecting, the indicator flashes orange rapidly (this process may take up to 4 minutes).

4. Indicator flashes green once the connection is established.

If connection fails, the indicator flashes red and alerts user with beeping frequencies. For troubleshooting, run [Unieye] to view the cloud warning message or refer to cloud warning table on page 8.

Step 4: View Live Video on Cloud Server

• To view live video, choose one of the following:

1. Use mobile app: USTREAM is available in Google Play or Apple Store.
2. Visit website: http://www.ustream.tv

- Then search for username and select "username's show" to watch live video through camera.

Note: 1. Cloud service may change depending on their policy.
2. In some areas, mobile may not activate hotspot where there is no 3G/4G.
3. Experiencing delays while viewing live video may be due to high internet traffic.

PC Applications

To use [Unieye] features on PC, install [PC APP] first. The [PC APP] has similar features and interface to [Unieye] for easy user experience.

Installing [PC APP] from Camera

• Connect the camera to PC via a USB cable.
  • [PC APP] AutoRun/AutoPlay activates.
• If AutoRun/AutoPlay is not starting:

Go to [My computer] and search [PC APP] for installation.

- Once installed, unplug the camera from PC then run [PC APP].

[PC APP] Features

• Press [View HD] or double-click the viewing window to maximize it into full screen. Double-click again to return to the [PC APP] interface.
  • To save videos or photos to PC:

Go to [Album]→ Select videos or photos Press [Save to PC].

Mass Storage and Webcam Modes

While camera is plugged in to PC, press Mode button on camera to switch between Mass Storage Mode (default) and Webcam Mode. The status indicator shows steady red in Mass Storage Mode and steady green in Webcam Mode (In Skype or QQ, select "UVC_WEBCAM").

Camera Indication

Condition Status Indicator Alert
Recording Flashing	green One time
Loop Recording Flashing	orange one time
Charging Flashing	red None
Fully Charged No indication	Two times
Low Battery	Flashing red every 5 sec. (Warning)
Power Off No indication	Two times
Auto Power Off (5 mins idle)	Flashing red Two times
Memory Full SD Card Error	Flashing red Three times

Camera Hotkey
Forced Shutdown	Press and hold Power button for 5 sec. to turn off camera.
Forced Default Settings	Press and hold Mode and Record buttons for 5 sec. to restore default settings.
Car Camcorder	Press and hold Record button for 3 sec. to start loop recording and invert image.

Troubleshooting

Situation Cause/Solution
Camera cannot turn on	Battery power is low. Recharge the battery.
Camera is frozen	Press Power button for 5 sec. to turn off. Press Power button twice to turn on.
Camera cannot record	No SD card or SD card is full. SD card cannot be recognized. Format SD card in [Unieye] or replace SD card.
Camera not found	Turn on camera, switch to Direct Mode. Press "Refresh" on mobile or PC to scan again.
Forgot camera password	Press both Mode and Record buttons for 5 sec. to reset.
Cannot watch live view	Move camera closer to mobile.
Flickering segments on live view	TV system setting (50Hz/60Hz) is incorrect.

Cloud Warning:

Alert Cause/Solution
One time	Cannot connect to cloud AP or invalid network password. Camera not inside WiFi area or weak signal. Check AP settings or move camera closer to cloud AP.
Two times	No internet or the cloud server is not accessible. Cannot log in cloud server via internet. Cloud service may be blocked by firewall.
Three times	Cloud server username or password is incorrect. Refer to i in [Setup] for instructions. Username already taken. Create new account in [Unieye].

Waterproof Housing Guide

Placing the Camera into the Waterproof Housing

1. Slide [OPEN] switch to the right and hold its position, then lift up the latch arm to open the housing.

1. Place the camera in the housing; camera's Record button must align with housing's spring button.

1. Hook hinged arm to the top of the backdoor, then push down the latch arm to snap into place.

Pure technical line drawing of a mechanical component or bracket (no text or symbols)

License Statement

The software used in this product is licensed subject to a license pursuant to the GNU – General Public License conditions.

We expressly draw attention to the fact that under the GNU – General Public License conditions no liability is accepted.

The starting point for the software is the software published online at

http://sg-gpl.net/

The software listed there is licensed pursuant to the GNU – General Public License conditions.

Device-related changes have been made to this software for the product in question. The source text of the software implemented in the product in question can be obtained in response to an enquiry sent to the e-mail address

[e-mail]

In this instance your e-mail must contain details of what the relevant product is, the relevant serial number and documentary evidence of your commercial source of supply as well as documentary evidence of the date on which the product was purchased from the trade source of supply. We guarantee supply of the source text of the implemented software for a period of at least three years from date of purchase from the trade source of supply where the trade source of supply has sourced the product from us directly or via strictly trade-only dealers.