STS 630 Set - Drill/Driver METABO - Free user manual and instructions

Product Type	Pneumatic Die Grinder
Brand	Metabo
Model	STS 630 Set
Dimensions (L x W x H)	180 mm x 41 mm x 66 mm
Weight	0.6 kg
Power Source	Compressed Air
Max. Permissible Working Pressure	6.2 bar
Air Consumption	340 l/min
No Load Speed	22,000 min⁻¹
Hose Inside Diameter	9 mm
Connector Thread	1/4"
Vibration Level (Weighted Acceleration)	8.1 m/s²
Sound Power Level (L_W)	105 dB(A)
Sound Pressure Level (L_PA)	92 dB(A)
Collet Sizes Included	3 mm and 6 mm
Grinding Points Included	5 each of 3 mm and 6 mm
Accessories Included	2 assembly spanners, 1 male coupling R 1/4", plastic case, operating instructions
Safety Features	Trigger with safety catch, air regulator, quick coupling required
Maintenance	Regular oiling (3-5 drops per 15 min), filter cleaning weekly, tighten screws
Recommended Oil	Pneumatic oil, e.g., Metabo art. no. 0901008540

Frequently Asked Questions - STS 630 Set METABO

What type of tool is the Metabo STS 630 Set?

The Metabo STS 630 Set is a pneumatic die grinder designed for grinding, deburring, rust removal, and milling in DIY applications.

What is the maximum air pressure for this tool?

The maximum permitted working pressure is 6.2 bar. Do not exceed this value.

How do I change the grinding point?

First, disconnect the tool from the air supply. Loosen the clamp nut, remove the old collet, insert the new grinding point into the appropriate collet, place it in the chuck, and tighten the clamp nut securely.

What lubrication does the STS 630 require?

It requires pneumatic oil. Add 3-5 drops every 15 minutes of continuous use, or 5-10 drops after storage, into the compressed air port.

Can I use this tool with explosive gases?

No. The tool must only be powered by compressed air and not operated with gases that are explosive, combustible, or detrimental to health.

What safety gear should I wear?

Always wear ear protection, safety glasses, protective gloves, and a dust respirator if the work generates dust.

How do I connect the tool to the air supply?

Install the plug nipple, set the operating pressure on the compressor (max 6.2 bar), and connect the quick coupler to the air supply.

What is the air consumption of this tool?

The air consumption is 340 liters per minute.

How often should I clean the filter?

Clean the filter in the compressed air connection at least once a week. Consider using a pressure reducer with water separator and oiler.

Where can I get the STS 630 repaired?

Repairs must be carried out by qualified specialists. You can send the tool to a Metabo service center in your country. Include a description of the fault.

USER MANUAL STS 630 Set METABO

Open gray toolbox containing various mechanical components and tools (no visible text or labels)

STS 630

ENG Operating Instructions 9

DECLARATION OF CONFORMITY

We herewith declare in our sole responsibility that this product complies with the following standards* in accordance with the regulations of the undermentioned Directives**

NL NEDERLANDS

CONFORMITEITSVERKLARING

Director Innovation, Research and Development

Dokumentationsbevollmächtigter/ responsible person for documentation/ Chargé de la documentation

Metabowerke GmbH

Metabo-Allee 1

D - 72622 Nürtingen

1. Components and Parts

1 Clamp nut
2 Air regulator
3 Compressed air connection with filter
4 Plug nipple
5 Trigger with safety catch
6 Collet, 2×
7 Chuck

Table of Contents

1. Components and Parts
2. Please Read First!
3. Safety
4. Operation
5. Care and Maintenance
6. Repairs
7. Protection of the Environment
8. Scope of delivery
9. Accessories
10. Technical specifications

2. Please Read First!

These operating instructions have been written so that you can quickly learn how to operate your device safely. Here is how to read the instructions:

• Read these instructions completely before use. Pay special attention to the safety information.
• These instructions are intended for persons having a basic technical knowledge in the handling of machines such as the one described here. Inexperienced persons are strongly advised to seek competent advice and guidance from an experienced person before operating this machine.
• If you notice transport damage while unpacking, notify your supplier immediately. Do not operate the tool!
• Keep all documents supplied with this machine for future reference. Retain proof of purchase for any future warranty claims.
• If you lend or sell this device be sure to have these Operating Instructions go with it.
  – The manufacturer is not liable for any damage arising from disregard of these instructions.

Information in these Operating Instructions is denoted as under:

Danger!

Risk of personal injury or environmental damage.

Caution!

Risk of material damage.

Note:

Additional information.

– Numbers in illustrations (1, 2, 3 etc.)
– denote component parts;
– are consecutively numbered;
– refer to the corresponding numbers in brackets (1), (2), (3) ... in the neighbouring text.
- Numbered steps must carried out in sequence.
- Instructions which can be carried out in any sequence are indicated by a bullet point (•).
– Listing are preceded by a dash (−).

3. Safety

3.1 Specified Conditions of Use

The die grinder is a compressed air-powered rotating grinding tool for DIY applications.

The die grinder is suitable for work such as grinding, deburring, rust removal and milling.

This tool may only be powered by a compressed air supply. The max. permissible working pressure stated in the Technical Specifications must not be exceeded. This tool must not be operated with gases that

are explosive, combustible or detrimental to health.

Any other use is not as specified. Use not as specified, modification of the tool or use of parts not approved by the manufacturer can cause unforeseeable damage!

3.2 General Safety Instructions

When using this air tool follow the safety instructions given below, to exclude the risk of personal injury or material damage.

Please also observe the special safety instructions in the respective chapters.

Observe the statuary accident insurance institution regulations and regulations for the prevention of accidents pertaining to the operation of air compressors and air tools, where applicable.

General hazards!

• Keep your work area tidy – a messy work area invites accidents.
• Be alert. Do not operate this tool while under the influence of drugs, alcohol or medication.
• Keep air tools out of the reach of children.
• Connect this tool to the compressed air supply by means of a quick coupling only.
• Make sure that the max. permissible working pressure stated in the Technical Specifications is not exceeded.

• Do not overload tool – use it only within the performance range it was designed for (see Technical Specifications).

• Working with this tool may generate sparks. Do not use the tool near flammable materials, liquids or gases.

• Do not touch any rotating parts.
• Disconnect this tool from air supply before
  – changing grinding points,
• servicing or
• when tool is left unattended.

Hazard generated by insufficient nal protection gear!

– Wear personal protection gear:
- ear protection,
- protective spectacle,
- protective gloves,
- dust respirator (when work generates dust).

Hazard generated by machine ts!

• Take good care of the tool. Observe the maintenance instructions.
• Do not attempt to repair the tool yourself! Only trained specialists are permitted to service or repair compressors, pressure vessels and air tools.

Caution!

• Protect the tool, particularly the air inlet, grinding point chuck and operating elements, from dust and dirt.
• Let tool run idle for a short time only.

3.3 Symbols on the machine

8 Please read the manual before using the tool.

9 Wear eye protection.

10 Wear ear protection.

11 CE symbol

4. Operation

4.1 Prior to initial operation

• Install the plug nipple.

4.2 Using the Tool

Caution!

The compressed air line must be free of condensed water.

Caution!

To ensure a long service life of this tool, it needs to be supplied with sufficient quantities of pneumatic oil. This can be achieved by:

- To obtain oil-containing compressed air attach an oiler or in-line oiler

or

- manually pour about 3 to 5 drops of pneumatic oil per 15 minutes of operation (continuous operation) into the

compressed air port or the fill hole for pneumatic oil.

If the tool has not been used for a period of at least several days manually pour about 5 to 10 drops of pneumatic oil into the compressed air port or the fill hole for pneumatic oil.

Danger!

Ensure the grinding point is seated securely.

Do not tilt the grinding point.

1. Loosen the clamp nut.

2. Select the appropriate collet and

3. insert the appropriate grinding point into the collet and place in the tool chuck.

4. Attach the clamp nut and tighten.

5. Set the operating pressure on the compressor (see 'Technical data' for maximum allowable working pressure).

6. Connect quick coupler to the air supply.

7. Adjust the speed by means of the adjusting screw.

8. To switch on attach retainer and press the trigger.

5. Care and Maintenance

Danger!

Always disconnect from air supply before servicing.

Maintenance and repair work not described in this chapter must be carried out by qualified specialists only.

• Check all screwed connections for tightness and tighten if necessary.
• Clean the filter in the compressed air connection at least once a week. It is recommended that a pressure reducer with water separator and oiler be connected in front of the tool.
• Do not store tool unprotected outdoors or in humid environment.

6. Repairs

Danger!

Repairs to air tools must only be carried out by qualified specialists!

Air tools in need of repair can be send to the service centre in your country. Refer to spare parts list for address.

Please attach a description of the fault to the air tool.

7. Protection of the Environment

All packaging materials are recyclable.

End-of-life tools and accessories contain large amounts of valuable raw materials and plastics which must be recycled.

This manual was printed on chlorine-free bleached paper.

8. Scope of delivery

1 die grinder STS 630 set
1 collet, ∅ 3 mm
1 collet, ∅ 6 mm
2 assembly spanners
5 each grinding points ∅ 3 mm and ∅ 6 mm
1 male coupling, R 1/4"
1 plastic case
1 Operating Instructions

9. Accessories

Pneumatic oil, 0.5 l, art. no.: 090 100 8540

Attachment oiler, R 3/8", art no.: 090 105 4592

10. Technical specifications

Air consumption l/min 340
Max. permissible working pressure bar 6.2
Speed	min^-1	22 000
Hose diameter (inside) mm 9.0
Connector thread " 1/4
Vibration (effective value of weighted acceleration)	m/s^2	8.1
EN ISO 15744sound power level L_W^* sound pressure level L_PA^* Uncertainty K	dB (A) dB (A) dB (A)	105 92 3
Dimensions: length x width x height mm	180 x 41 x 66
Weight	kg	0.6
* The values stated are emission values and as such do not necessarily constitute values which are safe for the workplace. Although there is a correlation between emission levels and environmental impact levels, whether further precautions are necessary cannot be derived from this. Factors influencing the actually present environmental impact level in the workplace include the characteristics of the work area and other noise sources, i.e. the number of machines and other neighbouring work processes. The permitted workplace values can likewise vary from country to country. This information is intended to assist the user in his estimate of hazards and risks.