HPE ProLiant DL360 Gen10 - Server HP - Free user manual and instructions
Find the device manual for free HPE ProLiant DL360 Gen10 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Server |
| Brand | HP |
| Model | HPE ProLiant DL360 Gen10 |
| Form Factor | 1U Rack |
| Chassis Dimensions (H x W x D) | 4.29 x 43.46 x 69.85 cm (1.69 x 17.11 x 27.5 in) |
| Weight | 14.5 kg (32 lb) |
| Processor Type | Intel Xeon Scalable (Bronze, Silver, Gold, Platinum) |
| Memory Type | DDR4 ECC SDRAM |
| Memory Slots | 24 DIMM slots |
| Maximum Memory | 3.0 TB with 128 GB modules |
| Storage Controller | HPE Smart Array P408i-a SR Gen10 |
| Drive Bays | Up to 10 SFF (2.5-inch) or 4 LFF (3.5-inch) hot-plug |
| Network Controller | Embedded 4x 1GbE or optional 10GbE |
| Power Supply Type | Hot-plug redundant |
| Power Supply Rating | 800 W or 1600 W (depending on configuration) |
| Management | HPE iLO 5 (Integrated Lights-Out) |
| Security Features | TPM 2.0, Secure Boot, Silicon Root of Trust |
| Operating Systems Supported | Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware ESXi |
| Cooling | 8 hot-plug fans with redundancy |
| Expansion Slots | 2 PCIe 3.0 slots (1 x16, 1 x8) |
| Warranty (Standard) | 3 years parts, labor, and onsite |
Frequently Asked Questions - HPE ProLiant DL360 Gen10 HP
How do I install 2.5-inch drives in the HPE ProLiant DL360 Gen10?
Open the front bezel, press the drive carrier latch, insert the drive into an empty bay, and close the handle until it clicks. Ensure the drive is compatible with the server.
How can I configure the HPE iLO 5 management controller?
During POST, press F8 to enter the iLO configuration utility. Set network settings, user accounts, and enable remote access. Alternatively, use the iLO web interface after initial setup.
What is the maximum supported memory?
The HPE ProLiant DL360 Gen10 supports up to 3.0 TB of DDR4 memory using 128 GB LRDIMMs across 24 DIMM slots. Mixing memory types is not recommended.
How do I update the BIOS or firmware?
Download the latest firmware package from the HPE Support Center. Use the iLO web interface or the System ROM Flash utility to apply updates. Always backup current settings.
How to reset the server to factory defaults?
Power off the server, then press and hold the UID button on the front panel for 5 seconds until the system LED blinks. This resets iLO and BIOS to factory defaults.
How to replace a power supply unit?
Power off the server or use the hot-plug feature. Unplug the power cord, press the release latch, and slide the power supply out. Insert the new unit firmly until it clicks.
How to set up RAID configuration?
Enter the Smart Storage Administrator via F5 during POST. Create a logical drive by selecting physical drives, RAID level, and stripe size. Ensure the drives are initialized.
Server does not power on, what should I check?
Verify power cables are connected, power supplies are seated, and the front power button is pressed. Check for LED indicators on the power supply and system board.
How to install a supported operating system?
Use the Smart Provisioning tool integrated into the server. Insert the OS media or use the Intelligent Provisioning interface to automate driver installation and OS deployment.
How to access remote management?
Once iLO is configured with an IP address, open a web browser and enter the iLO IP address. Log in with the iLO user credentials to access remote console, monitoring, and control.
User questions about HPE ProLiant DL360 Gen10 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual HPE ProLiant DL360 Gen10 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HPE ProLiant DL360 Gen10 by HP.