93198 - Smoke detector No-Flame - Free user manual and instructions

Product Type	Smoke Detector
Brand	No-Flame
Model	93198
Power Source	9V battery (included)
Sensor Type	Ionization
Alarm Loudness	85 dB at 3 meters
Test Button	Yes
Low Battery Indicator	Chirping sound
Hush Feature	Yes, temporary silence
Dimensions	100 mm diameter x 40 mm height
Weight	180 g
Mounting	Ceiling or wall mount
Operating Temperature	0°C to 40°C
Humidity Range	5% to 95% non-condensing
Compliance	UL 217 / EN 14604
Battery Life	Up to 1 year
Recommended Testing	Weekly
Cleaning Instructions	Vacuum dust from vents monthly
Replacement Parts	9V battery only
Warranty	5 years from purchase

Frequently Asked Questions - 93198 No-Flame

How do I install the No-Flame 93198 smoke detector?

Mount the detector on the ceiling or high on a wall, at least 10 cm from corners. Use the included screws and anchors. Insert the 9V battery, then press the test button to confirm operation.

How do I test the smoke detector?

Press and hold the test button until the alarm sounds (typically 3 seconds). The alarm should be loud and clear. If not, replace the battery or check for dust.

Why is my smoke detector chirping?

A chirp every 30-60 seconds indicates a low battery. Replace the 9V battery immediately. If chirping continues, clean the detector and ensure it is properly mounted.

How do I silence a false alarm?

Press the hush button to temporarily silence the alarm for about 8-10 minutes. The detector will automatically reset. If false alarms persist, relocate the detector away from kitchens or bathrooms.

Where should I place the smoke detector?

Install on every level of your home, especially outside sleeping areas. Avoid bathrooms, kitchens (to prevent false alarms), and near windows or vents. Ceiling mounting is preferred.

How often should I replace the battery?

Replace the 9V battery at least once a year, or when the low battery chirp begins. Use a fresh alkaline battery for best performance.

What is the lifespan of the smoke detector?

The No-Flame 93198 has a lifespan of approximately 10 years from manufacture date. Replace the entire unit after 10 years, even if it appears functional.

Can the smoke detector be interconnected with others?

No, this model is a standalone unit and cannot be interconnected with other detectors or systems.

How do I clean the smoke detector?

Use a soft brush or vacuum cleaner with a crevice tool to remove dust from the vents at least once a month. Do not use water or cleaning agents.

What do I do if the alarm doesn't sound during testing?

First, check the battery installation and polarity. Replace with a new battery. If still no sound, clean the detector. If the issue persists, the unit may be faulty and should be replaced.

USER MANUAL 93198 No-Flame

TRÅDL∅S R∅GALARM

Introduktion

Brug

Fremstillet i P.R.C.

6429 - Ningbo Kingdun Electronic Industry Co., Ltd., Zhejiang

EU-Importør:

HP Værktøj A/S

7080 Børkop

Danmark

Bruk

Fremstilt i P.R.C.

6429 – Ningbo Kingdun Electronic Industry Co., Ltd., Zhejiang

EU-importør:

HP Værktøj A/S

DK-7080 Børkop

Danmark

Användning

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

Turvallisuusohjeet

Käyttäminen

WIRELESS SMOKE ALARM

Introduction

To get the most out of your new wireless smoke alarm, please read through these instructions before use. We also recommend that you save the instructions in case you need to refer to them at a later date.

Technical data

Type: Photoelectric smoke alarm

Power consumption, smoke detector: ≤ 10 μA

Power consumption, transmitter: ≤ 120 μA

Operating temperature: -10 to +40 °C

Alarm: > 85 db (3 m)

Size: Dia. 125 x 50 mm

Frequency: 433.92 Mhz

Max. distance between alarms

(without obstacles): 60 m

Includes 1 x 9 V battery and 3 x 1.5 V

batteries (× 2)

Special safety instructions

The smoke alarm should not be installed anywhere where dust, smoke or steam is commonly present, for example, near cookers, in boiler rooms or bathrooms.

Test the smoke alarm regularly by pressing the test button.

Main components

1. Casing
2. Test button and LED
3. The LEARN button (connecting several alarms) and LED
4. Battery compartment for 9 V battery
5. Battery compartment for 1.5 V batteries
6. Mounting plate

Use

Choose a suitable place to install the smoke alarm.

As smoke rises, we recommend installing the smoke alarm on the ceiling in the middle of a room.

Twist the casing (1) off the mounting plate (6). Screw the mounting plate securely to the ceiling.

Insert a 9 V battery into the battery compartment of the smoke detector (4) and three 1.5 V batteries into the battery compartment of the transmitter (5).

Twist the casing securely onto the mounting plate. Press and hold the test button (2). The alarm should go off after a few seconds. Release the button.

When the alarm is functioning correctly, the red LED will flash every 43 seconds.

Connecting several smoke alarms in a network

1. Select one alarm to serve as the main alarm. Put it aside.
2. Select an alarm to be connected to the main alarm.
3. Press the LEARN button (3) on this alarm several times, so that the LED shines red.
4. If you are connecting several alarms, you should repeat point 3 for all the alarms to be connected to the main alarm.
5. Press the test button on the main alarm and hold it in until all alarms sound.

Replacing the battery

When the batteries are about to run out, the smoke alarm emits a loud warning signal.

If the 9 V battery in the smoke detector is about to run out, the warning signal sounds every 43 seconds.

If the three 1.5 V batteries in the transmitter are about to run out, the warning signal sounds every 60 seconds.

Replace the battery as soon as possible, and test the smoke alarm by pressing and holding the test button.

Remember to reconnect the smoke alarm to the network.

Cleaning and maintenance

Wipe the smoke alarm down regularly with a well-wrung cloth. Vacuum the casing if it becomes dusty.

Service centre

For:

• Complaints
• Replacements parts
• Returns
• Guarantee issues
• Open 7.00 to 16.00
  • E-mail: [e-mail]

Declaration of compliance

We hereby declare that

WIRELESS SMOKE ALARM

83198 (KD-101LD)

433,92 Mhz

has been manufactured in accordance with the following standards or normative documents:

EN 14604:2005

EN 300 220-2 V2.1.2

EN 301 489-01 V1.6.1

EN 301 489-03 V1.4.1

in accordance with the provisions of the following directives

89/106/EØF Construction Products Directive

1995/5/EC R&TTE directive (for radio and telecommunications terminal equipment)

1134-CPD-059

Stefan Schou

Purchasing manager

Environmental information

HP Værktøj A/S endeavours to manufacture environmentally-friendly electrical and electronic products; we also wish to contribute to the safe disposal of waste substances which may be environmentally hazardous.

A healthy environment is important for everyone, and we have therefore set ourselves the target of complying with the requirements in the EU's initiatives in this area, which means we guarantee the environmentally-sound collection, processing, recovery and disposal of electronic equipment which might otherwise harm the environment. This also means that our products do not contain any of the following chemicals or substances:

• Lead
• Mercury
• Cadmium
• Hexavalent chromium
• PBB (polybrominated biphenyls) (flame retardants)
• PBDE (polybrominated diphenyl ethers) (flame retardants)

HP Værktøj A/S is proud to support the EU's environmental initiatives in order to promote a cleaner environment and hereby declares that our products comply with both the WEEE Directive (2002/96/EC) and the RoHS Directive (2002/95/EC).

As a consumer, you can also play a part in protecting the environment by following the applicable environmental regulations and taking old electrical and electronic equipment to your local recycling centre. If the equipment contains batteries, you must remember to remove these before you dispose of the equipment.

Manufactured in P.R.C.

6429 - Ningbo Hailian Electric Appliance Co., Ltd., Zhejiang, China

EU Importer:

HP Værktøj A/S

DK-7080 Børkop

Denmark

All rights reserved. The contents of this user guide may not be reproduced in part or whole in any way, electronically or mechanically (e.g. photocopying or scanning), translated or stored in a database and retrieval system without the prior written consent of HP Værktøj A/S.

DRAHTLOSER RAUCHMELDER

Einleitung

Gebrauch

Sposób użycia

89/106/EEC Construction Products

Ohutuse erijuhised

Kasutamine