44-1514 - Hair straightener Clas Ohlson - Free user manual and instructions

Type of product	Alarm clock
Model	44-4809 (S714)
Brand	Clas Ohlson
Dimensions	63 × 63 × 63 mm
Power supply	3 × AAA/LR03 batteries or USB cable
Time memory battery	CR2032
Time format	12 or 24 hour
Alarm	1 daily alarm
Power save mode	On/Off (recommended On for battery operation)
Display	PM symbol, alarm symbol
Battery compartments	Outer for 3×AAA, inner for CR2032
Buttons	SET, UP, DOWN
USB port	Yes (micro-USB)
Care and cleaning	Wipe with lightly moistened cloth, mild detergent only
Safety	Indoor use only; avoid water, damp, dust, extreme temperatures, direct sunlight; do not open or modify
Reparability	CR2032 battery replaceable; other repairs only by qualified technician

Frequently Asked Questions - 44-1514 Clas Ohlson

How do I set the time on my Clas Ohlson alarm clock (44-4809)?

Press SET repeatedly until the time setting appears. Then hold SET for 2 seconds. Use UP/DOWN to choose 12/24 hour format, then press SET to set hours, then minutes. Wait 15 seconds or press SET again to save.

How do I set the alarm?

Press SET until '--AL' is displayed. Hold SET for 2 seconds, then set hours and minutes using UP/DOWN. The alarm symbol appears. The alarm rings for 1 minute and repeats daily unless turned off.

How do I turn the alarm off?

Press SET until '--AL' appears. Press UP to toggle between '--AL' (OFF) and 'oNAL' (ON). Select OFF to disable.

How does the power save mode work?

Press DOWN repeatedly to toggle. 'oNSd' means ON (display turns off after 10 seconds of inactivity). '--Sd' means OFF (display stays on). For battery operation, power save should be ON.

Why isn't my clock working on batteries?

Check if the AAA batteries are flat or inserted correctly (follow polarity markings). Also ensure the power save mode is ON to conserve battery.

Why isn't my clock working via USB?

Check the USB cable connection. Ensure the power source (computer) is not in standby. Try a different USB charger.

How do I replace the time memory battery (CR2032)?

Unscrew the inner battery cover on the back, remove the old CR2032, insert a new one with correct polarity, and refit the cover.

Can I use only batteries without USB?

Yes, but for optimal performance and battery life, USB power is recommended. When using batteries, always turn power save mode ON.

What should I do if the time is not saved after removing power?

Replace the CR2032 memory battery. It supports time retention when the main power is disconnected.

How do I clean the alarm clock?

Use a lightly moistened cloth with mild cleaning agents. Do not use solvents or corrosive chemicals.

USER MANUAL 44-1514 Clas Ohlson

Abstract black circular graphic symbol on white background (no text or symbols)

Wooden Cube Alarm Clock

SE | Bordsklocka träkub med alarmfunktion NO | Bordklokke med alarm, trekube FI | Pöytäkello jossa herätys

Art.no. Model

44-4809 S714

Ver. 20220711

Wooden Cube Alarm Clock

Art.no 44-4809 Modell S714

Please read the entire instruction manual before using the product and then save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data. In the event of technical problems or other queries, please contact our Customer Services (see address details on the back).

Safety

• The clock must only be repaired by qualified service technicians.
• The clock is for indoor use only.
• Do not place the clock where there is a risk of it falling into water or other liquid.
• Do not place the clock in damp, dusty environments or where there is an occurrence of strong vibrations.

• Do not expose the clock to extremely high or low temperatures. Do not expose the clock to direct sunlight.

• Never try to open, change or modify the clock in any way.

• Always remove the batteries if the clock is not to be used for a long time.

Product description

1. Display
2. PM symbol
3. Alarm symbol

1. Outer battery cover
2. [SET] Settings
3. [UP] Move up in menu, increase a value
4. [DOWN] Move down in menu, decrease a value

5. USB port

6. Compartment for 3 × AAA/LR03 batteries

7. Inner battery cover

8. CR2032 battery for time memory

Operating instructions

Note: For optimum operation and to preserve battery charge, the alarm clock should be powered using the USB cable wherever possible.

Operation using USB cable

Connect the clock to a computer or other USB charging device using the included USB cable. Note: A compatible USB charger is not included but can be purchased separately.

Battery operation

1. Remove the outer battery cover (4) by lifting the tab on the bottom edge. Lift it up and the cover will come away.
2. Insert 3 × AAA/LR03 batteries into the battery compartment (9), observing the correct polarity (see the markings inside the battery compartment).
3. Refit the battery cover by first slotting in the two tabs in the top edge and then pressing down on the bottom edge.

Setup

Time

1. Press [ SET ] repeatedly until the time setting is displayed.

2. Hold in [SET] for 2 seconds.

3. Press [UP]/[DOWN] to change between 12-hour and 24-hour clock display.

4. If the 12-hour clock format is chosen, the PM symbol will be displayed in the top left corner of the display in the afternoon.

5. Press [SET] and the hours will begin to flash.

6. Press [UP]/[DOWN] to set the hours.
7. Press [SET] and the minutes will begin to flash.
8. Press [UP]/[DOWN] to set the minutes.
9. Press [ SET ] or wait for 15 seconds and the setting will be saved.

Handy tip: Holding the [UP] or [DOWN] button down will change the time quickly.

Alarm

1. Press [ SET ] until “--AL”, is displayed.

2. Hold down [ SET ] for 2 seconds and the hours will begin to flash.

- Press [UP]/[DOWN] to set the hours.

1. Press [SET] and the minutes will begin to flash.

- Press [UP]/[DOWN] to set the minutes.

1. Press [SET] or wait for 15 seconds and the setting will be saved.

- The alarm is now on and the alarm symbol will show on the display.

- The alarm clock will emit a ring signal at the set time, the signal will sound for 1 minute or until any of the buttons on the back is pressed.

- The clock will sound the alarm at the same time every day unless the alarm function is switched off.

- The alarm is switched off by pressing [ SET ] until the alarm time “--AL”, is displayed.

- Press [UP] to toggle between

- ”--AL” (OFF)

- "oNAL" (ON).

Power save mode on/off

Note: During battery operation the power save mode should always be ON.

Press [DOWN] repeatedly to switch between power save mode ON/OFF.

1. When “oNSd” is displayed, the power save mode is ON.

2. When “--Sd” is displayed, the power save mode is OFF.

3. The display will switch off after 10 seconds of inactivity and remain off until any of the sides of the cube is touched or until the alarm sounds.

Time memory

The clock has a built-in memory for the time and date. The memory is powered by a factory-installed CR2032 battery which can be replaced if the clock no longer saves the time after the power source has been disconnected.

1. Replace the battery by unscrewing the inner battery cover (10).
2. Remove the cover and change the battery.
3. Refit the battery cover and secure it with the screw.

Care and maintenance

Clean the product using a lightly moistened cloth. Use only mild cleaning agents, never solvents or corrosive chemicals.

Troubleshooting guide

The clock does not work on battery power.	Check that the AAA batteries are not flat.Check for correct battery insertion.
The clock does not work on USB cable power.	Is the cable connected correctly?Is power source computer in standby mode?Is the USB charger defective?
Time and date not saved following power removal.	Replace the CR2032 battery for the memory.

Responsible disposal

This symbol indicates that this product should not be disposed of with general household waste. This applies throughout the entire EU. In order to prevent any harm to the environment or health hazards caused by incorrect waste disposal, the product must be handed in

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or numbers present)

for recycling so that the material can be disposed of in a responsible manner. When recycling your product, take it to your local collection facility or contact the place of purchase. They will ensure that the product is disposed of in an environmentally sound manner.

Specifications

Power supply 3 × AAA/LR03 batteries or USB cable (CR2032 battery for memory)

Time format 12 or 24 hour clock

Alarms 1

Power save mode On/Off

Size 63 × 63 × 63 mm

1. Display
2. PM-symbol
3. Alarmsymbol

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or numbers present)

Specifikationer

1. Display
2. PM-symbol
3. Alarmsymbol

Simple line drawing of a trash bin with two crossed lines indicating no waste or prohibition (no text or symbols)

en ansvarsfull måte. Benytt miljøstasjonene som er der du befinner deg eller ta kontakt med forhandler. De vil ta hånd om produktet på en miljømessig tilfredsstillende måte.

Spesifikasjoner

Strømforsyning 3 × AAA/LR03-batterier eller USB-kabel (CR2032-batteri til tidsminnet)

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or numbers present)