CN15F - Motion detector Elektrobock - Free user manual and instructions
Find the device manual for free CN15F Elektrobock in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Motion Detector |
| Brand | Elektrobock |
| Model | CN15F |
| Detection Range | Up to 12 m |
| Detection Angle | 180° |
| Mounting Height | 1.8 - 2.5 m |
| Power Supply | 230 V AC, 50 Hz |
| Maximum Load | 2000 W (incandescent), 400 W (LED) |
| Standby Power | <0.5 W |
| Time Delay Adjustment | 10 sec - 5 min |
| Light Sensor Threshold | 3 - 2000 lux (adjustable) |
| Operating Temperature | -20°C to +40°C |
| Protection Rating | IP44 |
| Material | Polycarbonate |
| Color | White |
| Dimensions (H x W x D) | 100 x 80 x 70 mm |
| Weight | 150 g |
| Installation Type | Wall or ceiling mount |
| Wiring | 3-wire (L, N, L') |
| Warranty | 2 years |
Frequently Asked Questions - CN15F Elektrobock
How do I install the CN15F motion detector?
Turn off the power at the fuse box. Connect the wires: L (live) to L, N (neutral) to N, and L' (switched live) to the light. Mount the detector at the recommended height of 1.8-2.5 m using the provided screws. Restore power and adjust settings.
How can I adjust the detection range?
The detection range is fixed up to 12 m. You can reduce the range by partially covering the sensor lens with the included adhesive tape or by adjusting the mounting angle.
Why does my light stay on all the time?
This may be due to the time delay set too long, or the light sensor threshold set to night-only mode. Check the time dial setting (10 sec to 5 min) and adjust the light sensor (lux) to a higher value to activate only in darkness.
What is the maximum load for LED bulbs?
The maximum load for LED bulbs is 400 W. For incandescent bulbs, it is 2000 W. Ensure the total connected load does not exceed these values.
Can I use the detector with a dimmer?
No, this motion detector is not compatible with dimmers. Use only with standard on/off switches.
How do I clean the motion detector?
Wipe the housing with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the sensor lens clean for optimal detection.
What does the L' terminal mean?
L' is the switched live output. It provides power to the connected light when motion is detected. It is normally off and switches on during detection.
The detector triggers false alarms. What can I do?
False alarms can be caused by moving branches, animals, or heat sources. Adjust the sensor angle away from such areas. Lower the sensitivity if adjustable (not on this model). Ensure the detector is not facing directly at a road or walkway.
Is the CN15F suitable for outdoor use?
Yes, it has an IP44 rating, meaning it is splash-proof and suitable for covered outdoor areas. Avoid direct exposure to heavy rain.
How do I reset the detector to factory settings?
This model does not have a factory reset button. To reset, turn off the power for 10 seconds and then turn it back on. All adjustable settings (time and lux) will need to be manually adjusted again.
User questions about CN15F Elektrobock
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motion detector in PDF format for free! Find your manual CN15F - Elektrobock and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CN15F by Elektrobock.
USER MANUAL CN15F Elektrobock
DETEKČNÍ POLE (ROZSAH POKRYTÍ)
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Elektrobock
Model : CN15F
Category : Motion detector