CN05B - Motion detector Elektrobock - Free user manual and instructions
Find the device manual for free CN05B Elektrobock in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Motion Detector (PIR) |
| Brand | Elektrobock |
| Model | CN05B |
| Detection Technology | Passive Infrared (PIR) |
| Detection Range | Up to 12 meters |
| Detection Angle | 180 degrees |
| Power Supply | 12-24V DC / AC |
| Power Consumption | < 0.5W |
| Dimensions | Approx. 105 x 65 x 45 mm |
| Weight | Approx. 55 g |
| Mounting | Wall or ceiling mount |
| Adjustable Time Delay | 10 seconds to 10 minutes |
| Light Sensor | Built-in (disable during daytime) |
| Operating Temperature | -20°C to +40°C |
| IP Rating | IP44 (indoor use recommended) |
| Maintenance | Clean with a dry, soft cloth; avoid solvents |
| Safety | Low voltage device; disconnect power before installation |
| Spare Parts | None available; the device is non-repairable |
| General Information | Designed for automatic lighting control; includes wiring diagram in manual |
Frequently Asked Questions - CN05B Elektrobock
How do I install the CN05B motion detector?
First, disconnect the power. Mount the detector at a height of 2-2.5 meters on a wall or ceiling. Connect the wires according to the wiring diagram in the manual (typically live, neutral, and load). Ensure the sensor faces the detection area.
What is the detection range of the CN05B?
The detection range is up to 12 meters with a 180-degree angle. Actual range may vary depending on installation height and environment.
How can I adjust the time delay?
The time delay is adjustable via a potentiometer on the device. Turn it clockwise to increase the delay (up to 10 minutes) and counterclockwise to decrease (down to 10 seconds).
Can the CN05B be used outdoors?
The device has an IP44 rating, meaning it is splash-proof. It can be used outdoors under an eave or in a sheltered location, but not in direct rain or extreme conditions.
Why does the light stay on continuously?
This usually happens if the time delay is set too high or if the sensor is detecting continuous movement (e.g., pets, swaying branches). Check the sensitivity and reduce the time delay.
How do I clean the motion detector?
Switch off the power. Wipe the lens and housing with a dry, soft cloth. Do not use water, solvents, or abrasive cleaners.
What should I do if the detector does not work?
Verify the power supply is correctly connected and within 12-24V DC/AC. Check that the light sensor is not blocked (cover it during testing). Reset the device by turning off power for 10 seconds.
What is the purpose of the light sensor?
The built-in light sensor prevents the detector from triggering during daytime. It can be adjusted or bypassed depending on your model version.
Can I replace the battery or internal parts?
No, the CN05B is a non-repairable device. There are no user-serviceable parts. If faulty, please replace the entire unit.
Which lamp types can be controlled by the CN05B?
The detector can switch incandescent, halogen, LED, and CFL lights up to its rated load. Check the manual for maximum wattage (typically 1000W incandescent / 300W LED).
User questions about CN05B Elektrobock
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motion detector in PDF format for free! Find your manual CN05B - Elektrobock and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CN05B by Elektrobock.
USER MANUAL CN05B Elektrobock
INFRAČERVENÉ POHYBOVÉ INFRAČERVENÉ POI ČIDLOČIDLO ČNÚJBC
DETEKČNÍ POLE (ROZSAH POKRYTÍ)
Schéma zapojení:
Table of contents
Click a title to access it
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Elektrobock
Model : CN05B
Category : Motion detector