220 MasterLINE - Motion detector Busch-Jaeger - Free user manual and instructions

Product Type	Passive Infrared Motion Detector
Brand	Busch-Jaeger
Model	220 MasterLINE
Power Supply	230 V AC
Detection Principle	Passive infrared (PIR)
Minimum Mounting Height	1.7 m
Switch-Off Delay	Adjustable via trim potentiometer (short-time pulse available)
Brightness Threshold	Adjustable via trim potentiometer
Test Mode	10-minute test mode (daytime operation, 2 sec switch-off delay)
Status LED	Flashes quickly on detection in test mode
Maximum Switching Current	Depends on ballast manufacturer specification
Dimensions (Approx.)	120 x 80 x 80 mm
Weight (Approx.)	150 g
Protection Class	IP44 (typical for outdoor use)
Operating Temperature	-20°C to +40°C
Safety Notes	Installation by authorized electricians only; disconnect power before handling
Care and Cleaning	Clean lens with a soft, dry cloth; do not press on lens
Spare Parts / Repairability	Contact manufacturer or authorized service center

Frequently Asked Questions - 220 MasterLINE Busch-Jaeger

What is the minimum mounting height for the Busch-Jaeger 220 MasterLINE?

The minimum mounting height is 1.7 m.

Can I install the motion detector myself?

No. Due to 230 V mains voltage, installation must be performed by authorized electricians only.

How do I test the motion detector after installation?

Set the selector switch to T/S (test mode). The device will be in test mode for 10 minutes with a 2-second switch-off delay. Each detection is indicated by a flashing status LED.

What does the trim potentiometer for brightness do?

It adjusts the brightness threshold at which the detector activates. Turn it to set the desired ambient light level.

How do I adjust the switch-off delay?

Use the trim potentiometer for switch-off delay. It can be set from a short pulse to a longer delay.

Why does the status LED flash quickly?

In test mode, the status LED flashes quickly to indicate detection of movement.

Can I use the motion detector with a push-button?

Yes, when using a break switch (push-button), the lighting switches on for the set operating mode.

How do I clean the lens?

Use a soft, dry cloth. Do not press on the lens as it is sensitive and can be damaged.

What should I do if the device does not detect movement?

Check that the mounting height is at least 1.7 m and that the brightness threshold is set correctly. Also ensure the lens is clean.

How do I reset the device to test mode?

Interrupt the power supply for more than 15 seconds or set the selector switch back to T/S. This activates another 10-minute test mode.

USER MANUAL 220 MasterLINE Busch-Jaeger

Risk of death and fire due to electrical voltage of 230 V

- work on the 230V supply system may only be performed by authorised electricians; - Disconnect the mains power supply prior to installation and/or disassembly!

- Detailed user information is available via the link in the "Service" chapter or by scanning the QR

codes (device with corresponding software is required)

- Maximum - Switching Current. The ballast manufacturer's specification determines the possible number of ballasts.

- The Busch-Watchdog is a passive infrared movement detector which switches loads through a

time element when sources of heat move within its detection range

The Busch Watchdoglot an intrusion of attack alarm

Electrical connection

With break switch: On: during the set switch-off delay.

With RC-fuse 6899 and relay

Met RC-suppressor 6899 en relais

Montego

Montageorte

Mounting

Installation sites

Die minimale Montagehöhe des Gerätes beträgt 1,7 m. The minimum height for installing the device is 1.7 m. De minimale montagehoogte van het apparaat bedraagt 1,7 m.

Reichweite

Coverage

Caution! Risk of damaging the device!

The lens of the device is sensitive and can easily sustain

- Do not press on the lens when setting the device!

Preparing the installation

• Remove the locking screw (1) (if installed).
• Press in clamps (2 - 5) on the sides of the housing with a suitable tool
  Sundals 100%

- Carefully remove the front of the device

Montage voorbereiden

Depending on where the device is installed, the water drain

may have to be opened.

– To do this, pierce the plastic membrane on the bottom of the

device

Waterafvoer

Set selector switch to T/S.
- The device is now in test mode for 10 minutes (daytime operation, switch-off delay 2 sec.). In addition, each detection is indicated by the status LED flashing quickly.
- After this, the device switches back to standard operating mode. - To carry out an additional activation test, set the selector switch back to position T/S or interrupt the operating voltage supply for more than 15 seconds.
- The device is now in test mode for another 10 minutes. Test mode is exited automatically after 10 minutes or by adjusting the brightness.