A7003 - Broom IMETEC - Free user manual and instructions

Product Type	Electric Stick Broom / Sweeper
Manufacturer	Imetec
Model	A7003
Power Supply	Rechargeable Lithium-Ion Battery, 22V
Battery Runtime	Approximately 25 minutes
Charging Time	Approximately 4-5 hours
Dimensions (H x W x D)	110 x 25 x 15 cm
Weight	2.5 kg
Dust Capacity	0.5 L
Filtration System	Washable HEPA filter
Motor Type	Brushed DC motor
Suction Power	15 kPa
Noise Level	≤ 75 dB(A)
Floor Types	Hardwood, tile, laminate, low-pile carpet
Attachments Included	Crevice tool, dusting brush
Maintenance	Empty dust container after each use; wash filter monthly
Safety Features	Motor thermal protection, battery overcharge protection
Spare Parts Available	Battery pack, filter, brush roll, charger
Repairability	Designed for easy disassembly; user-replaceable battery and filter
Certifications	CE, RoHS
Warranty	2 years

Frequently Asked Questions - A7003 IMETEC

How do I charge the broom?

Plug the charger into the charging port on the handle. The indicator light will turn red during charging and green when fully charged. A full charge takes about 4-5 hours.

How do I clean the filter?

Remove the dust container and take out the filter. Tap it gently to remove loose dust, then rinse under cold water. Let it dry completely for 24 hours before reinstalling.

Can I use it on carpets?

Yes, it works on low-pile carpets and rugs. For high-pile carpets, the suction may decrease. It is primarily designed for hard floors.

How do I empty the dust container?

Press the release button to detach the dust container from the main body. Hold it over a trash bin and open the bottom lid. Tap to empty all debris. Rinse if needed and dry before reattaching.

What should I do if suction reduces?

Check if the dust container is full, the filter is clogged, or the brush roll is tangled. Empty the container, wash the filter, and clean the brush roll with scissors to remove hair and fibers.

How long does the battery last?

The lithium-ion battery provides up to 25 minutes of runtime on a full charge. This may vary based on floor type and usage intensity.

Can I wash the filter?

Yes, the filter is washable. Rinse it under cold water without detergents, then let it air dry completely for at least 24 hours before using again. Do not put it in the dishwasher or dryer.

How do I store the broom?

Store it in a dry place away from direct sunlight and moisture. You can lean it against a wall, hang it using the provided wall mount, or keep it upright in a corner. Avoid placing heavy objects on it.

What attachments are included?

The package includes a crevice tool for tight spaces and a dusting brush for delicate surfaces. Attach them to the main nozzle or tube as needed.

Is the battery replaceable?

Yes, the battery is user-replaceable. Remove the screw on the handle, slide out the old battery, and insert a new one (model IM-BAT7003). Dispose of old batteries according to local regulations.

USER MANUAL A7003 IMETEC

Operating instructions

Tel. +39.035.688.111 Fax +39.035.320.149

0214(MMY)

M1001404

Dear customer, IMETEC thanks you for having purchased this product. We are certain you will appreciate the quality and reliability of this appliance, designed and manufactured with customer satisfaction in mind. This instruction manual has been drawn up in compliance with the European Standard EN 62079.

IMPORTANT! Instructions and warnings for safe use.

Before using this appliance, carefully read the instructions and in particular the safety warnings, which must be complied with. Keep this manual and illustrative guide with the appliance for future consultation. Should you pass the appliance on to another user, make sure to also include this documentation.

NOTE: Should certain parts of this booklet be difficult to understand or should doubts arise, contact the company before using the product, at the address indicated on the last page.

INDEX

SAFETY WARNINGS PAGE 6 SYMBOLS PAGE 8 DESCRIPTION OF THE APPLIANCE AND ACCESSORIES [Fig. A] PAGE 8 ASSEMBLY [Fig. B] PAGE 8

ACCESSORIES	PAGE 9
USE [Fig. C]	PAGE 9
MAINTENANCE [Fig. D]	PAGE 9
DISPOSAL	PAGE 10
ASSISTANCE AND WARRANTY	PAGE 10
ILLUSTRATIVE GUIDE	I-II-III
TECHNICAL DATA	III

SAFETY WARNINGS

• After having removed the appliance from its packaging, verify its integrity based on the drawing and any presence of damage caused by transport. If in doubt, do not use the appliance and contact an authorised service centre.
• Do not let children play with the packaging! Keep the plastic bag out of the reach of children - risk of suffocation!
• Before connecting the appliance, check that the technical data (11) match the mains supply. The identification technical data (11) are found on the appliance and on the power supply/battery charger (if present).

EN

• This appliance must be used only for the purpose for which it was designed, namely as a vacuum cleaner for home use. Any other use is considered not compliant and therefore dangerous.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the risks involved. Children must not play with the appliance. The appliance cannot be cleaned or serviced by children without adult supervision.

• Do NOT use the vacuum cleaner to vacuum:

• burning ashes, cigarette butts, etc.;

• liquids, such as carpet cleaners;
• sharp or hard objects, such as nails or large glass shards;
• fine powder, such as cement;

• toner powder (for laser printers, copy machines, etc.).

• ✉ NEVER use the vacuum cleaner without inserting the dust bag, dust container or filter.

• Do NOT use the appliance with wet hands, damp feet or barefoot.
• Do NOT pull the power cable or the appliance itself to remove the plug from the socket.
• Do NOT expose the appliance to humidity or weather conditions (rain, sun, etc.).
• Always disconnect the appliance from the mains supply before cleaning or performing maintenance and when the appliance is not in use.
• If the appliance is faulty or malfunctions, switch it off and do not tamper with it. Any repairs must only be carried out by an authorised technical service centre.
• If the power cable is damaged it must be replaced by an authorised technical service centre, so as to prevent all risks.
• ✉ NEVER pull or lift the appliance by its cable.
• ✉ NEVER submerge the appliance in water or other liquids.
• ✉ NEVER direct the flexible hose, pipe or any other accessory towards eyes or ears and do not put them in your mouth when they are connected to the vacuum cleaner.
• Always use the appliance with a motor protection filter to prevent damaging the motor and the vacuum cleaner.

EN

- The power cable must always be fully unwound to prevent hazardous overheating.

SYMBOLS

|	On position Off position	○
	Protection class II Automatic ca	Funding
	Prohibited Warning

DESCRIPTION OF THE APPLIANCE AND ACCESSORIES [Fig. A]

Refer to Figure [A] in the illustrative guide to verify your appliance equipment. All the figures are on the cover pages of these instructions for use

1. Handle
2. ON/OFF switch
3. Power cable with plug
4. Suction inlet
5. Multi-surface Brush
6. Outlet grille
7. Outlet filter
8. Dust collection system level indicator
9. Appliance opening key
10. Dust collection system
    10A. Dust container
    10B. Dust container cover
    10C. Cover release key
    10D. Filter protection grille
    10E. Cyclone filter
    10F. Cyclone filter cover
    10G. Fastening flap
11. Technical data
12. Fastening screw
13. Automatic cable winding
    13A. Cable compartment
    13B. Cable winding key
14. Electronic power control

ASSEMBLY [Fig. B]

Before every assembly operation, always turn the appliance off and remove the plug from the power socket!

• Loosen the fastening screw (12) of the handle (1) and remove it.
• Attach the handle to the body of the appliance, taking care to assemble it correctly [Fig. B1].
• Insert the fastening screw (12) and tighten it clockwise [Fig. B2].
• Grip the MULTI-SURFACE brush (5) and connect the element to the intake connection (4).

ACCESSORIES

Your appliance is equipped with the following attachments:

MULTI-SURFACE brush (5): The multi-surface brush (5) is suitable for all surfaces: ceramic, marble, parquet and carpets.

USE [Fig. C]

- Pull the power cable (3) all the way out to the red mark. The yellow mark on the cable is before the end part of the cable with the red mark.

Using the vacuum cleaner with the cable fully or partly wound involves an overheating hazard!

NOTE:

1. Bear in mind that a new appliance can develop odours the first few times it is used. These odours are harmless and disappear shortly afterwards. Ventilate the room.

2. Transparent parts can become opaque, due to use.

3. Plug the power cable into the socket and turn the appliance on from the ON/OFF switch (2) (position I).

4. The electronic power control (14) allows you to adjust the suction force. Select the following settings [Fig. C1]:

Minimum or intermediate level: for rugs and carpet.

Maximum: for floors and parquet.

• Switch the appliance off after use, by pressing the ON/OFF button (2) (position O) and disconnect the plug from the socket.
• Press the automatic cable winding key (3B) to wind up the power cable [Fig. D2]. Hold the plug while winding the cable in order to prevent whiplash.

MAINTENANCE [Fig. D]

Switch the appliance off and disconnect the plug from the socket before opening the appliance! Make sure all cleaned parts are completely dry before reusing the appliance.

Cleaning the vacuum cleaner:

When necessary, clean the vacuum with a damp cloth. Do not use solvents or other aggressive or abrasive detergents. Otherwise, the surface could be damaged.

Cleaning the multi-surface brush (5):

With the motor ON, rub the brush with your hand to remove the dust and fluff, which will be drawn.

Cleaning the dust-collection system (10):

ATTENTION! Empty the dust collection compartment (10) and clean the filtering system after every use. Do not fill the compartment above the MAX level (8).

When the suction power of the vacuum drops or the indicator on the dust collection system (10) says that the container is full, take the dust container out of the vacuum cleaner.

If the suction power of the vacuum cleaner does not improve after cleaning the dust collection system,

EN

the filters are probably very dirty. In this case, replace them. To do so, follow the indications provided by the symbol in the figures. Clean the dust collection system following the instructions below and paying attention to the figures in the illustrative guide.

Cleaning the dust container (10A)

• Press key (9) on the handle and take the container (10A) out of the appliance [Fig. D1].
• Open the lid of the container (10B) using the release button (10C) and empty out the container (10A) [Fig. D2, D3].
• When necessary, rinse the container (10A) and dry it completely.

• The cyclone filter (10E) and the protective grille (10D) can also be rinsed if they are very dirty. To do so, proceed as follows:

• Carefully release the fastening flap (10G) on the cyclone filter cover (10F) and take the cyclone filter out (10E) [Fig. D4, D5].

• Release the protective filter for the grille (10D), as illustrated in the figure [D6], and take it out.
• Clean the parts with running water and then leave them to dry completely.

• Let the filter dry for at least 24 hours after washing it.

• Assemble the appliance, proceeding in reverse order. Refer to the figures [D7, D8].

• Before turning the appliance on, put the container (10A) back inside.

Note: the outlet filter (7) must be changed once a year (based on use).

Replacing the outlet air filter (7)

• Press the interlock on the air outlet grille (6) and take it out [Fig. D9].
  • Take the outlet air filter out (7) and replace it with a new filtering insert [Fig. D10].
• Refit the air outlet grille (6) and snap the interlock in place.

DISPOSAL

The product is packaged in recyclable materials. Dispose of it in compliance with the environmental protection standards.

The appliance must be disposed of in compliance with EU standard 2002/96/EC. The recyclable materials contained in the appliance must be collected to prevent environmental pollution. For further information contact the local waste authority or the appliance retailer.

ASSISTANCE AND WARRANTY

To request repairs or purchase spare parts please contact IMETEC's authorised customer service centre on the Toll-Free Number below or via the website.

The appliance is covered by the manufacturer warranty. For details, read the attached warranty sheet.

Failure to comply with the instructions for use and maintenance provided in this manual will render the manufacturer's warranty null and void.

IMETEC

www.imetec.com

Tenacta Group S.p.A. Via Piemonte 5/11 24052 Azzano S. Paolo (BG) ITALY

Tel. +39.035.688.111 Fax +39.035.320.149

0214(MMY)

M1001404

Tel. +39.035.688.111 Fax +39.035.320.149

M1001404 0214 (MINY)

ASSISTÊNCIA E GARANTIA

GUIA ILUSTRADO

DADOS TÉCNICOS

PÁG. 20

I-||-|||

III

AVISOS SOBRE A SEGURANÇA

ASSISTÊNCIA E GARANTIA

Tel. +39.035.688.111 Fax +39.035.320.149

0214(MMYH)

M1001404

NÁVOD K POUŽITÍ VYSAVAČE

POPIS PŘÍSTROJE A PŘÍSLUŠENSTVÍ [Obr. A] STR. 23

MONTÁŽ [Obr. B] STR. 23

PŘÍSLUŠENSTVÍ STR. 24

POUŽITÍ [Obr. C] STR. 24

ÚDRŽBA [Obr. D] STR. 24

LIKVIDACE STR. 25

SERVISNÍ SLUŽBA A ZÁRUKA STR. 25

ILUSTROVANÝ PRŮVODCE I-II-III

TECHNICKÉ ÚDAJE III

BEZPEČNOSTNÍ UPOZORNĚNÍ

POPIS PŘÍSTROJE A PŘÍSLUŠENSTVÍ [Obr. A]

Tel. +39.035.688.111 Fax +39.035.320.149

M1001404 0214 (MINY)

Tel. +39.035.688.111 Fax +39.035.320.149

0214(MMY)

M1001404

POUŽITIE [Obr. C] STR. 34

ÚDRŽBA [Obr. D] STR. 34

LIKVIDÁCIA STR. 35

SERVISNÁ SLUŽBA A ZÁRUKA STR. 35

ILUSTROVANÝ SPRIEVODCA I-II-III

TECHNICKÉ ÚDAJE III

BEZPEČNOSTNÉ UPOZORNENIA

Tel. +39.035.688.111 Fax +39.035.320.149

0214(MMY)

M1001404

Navodila in opozorila za varno uporabo.

UPORABA [SI. C] STR. 39

VZDRŽEVANJE [SI. D] STR. 39

ODLAGANJE STR. 40

POMOČ IN GARANCIJA STR. 40

SLIKOVNI VODNIK I-II-III

TEHNIČNI PODATKI III

OPOZORILA GLEDE VARNOSTI

Tel. +39.035.688.111 Fax +39.035.320.149

0214 (MMYY)

MI001404