SC-276 - Curling iron Scarlett - Free user manual and instructions

Product Type	Hair Styler with Curling Iron Attachment
Brand	Scarlett
Model	SC-276
Power Supply	220-240 V ~ 50/60 Hz (check rating label)
Power Consumption	Approximately 1000 W (typical for hair stylers)
Speed Settings	3 speeds + Cool Shot
Cool Shot Function	Yes, for setting hairstyle
Attachments Included	Concentrator, Half Round Brush, Brush Barrel, Curling Iron
Attachment Release	Push-button for quick removal
Cord Type	Swivel cord for easy movement
Hanging Loop	Yes, for storage
Safety Features	Overheat protection, auto shut-off (not specified, but typical), do not use near water
Cleaning	Unplug, cool, wipe with damp cloth, no abrasives
Storage	Cool dry place, do not wrap cord around appliance
Warranty	Refer to manufacturer
Dimensions	Approximately 25 x 6 x 6 cm (estimated)
Weight	Approximately 0.5 kg (estimated)

Frequently Asked Questions - SC-276 Scarlett

How do I use the curling iron attachment?

Comb a lock of hair, twist it around the curling iron starting from the ends, hold for a few seconds, then release. Let the curl cool before combing.

Can I use this styler in the bathroom?

It is not recommended. The manual states to keep away from water. Always unplug after use. For safety, install a residual current device (RCD) if used in a bathroom.

What is the 'Cool Shot' function for?

The Cool Shot function blows cool air to set your hairstyle in place. Use after styling to lock in the shape.

How do I clean the attachments?

Unplug the appliance, let it cool, then wipe attachments with a damp cloth. Do not use abrasive cleaners. Ensure they are dry before storing.

Why does my styler turn off automatically?

The styler has an overheat protection. If it gets too hot, it will shut off. Let it cool for at least 10 minutes before using again.

Can I wrap the cord around the styler for storage?

No. The manual advises against wrapping the cord around the appliance to prevent damage. Instead, store it loosely coiled.

What voltage does the SC-276 work with?

Check the rating label on the device. Typically it is 220-240 V ~ 50/60 Hz. Do not use with a different voltage without a converter.

How do I change the attachments?

Press the attachment release knob (button) on the styler and pull off the current attachment. Snap on the desired one until it clicks.

Is the curling iron attachment suitable for all hair types?

Yes, but adjust the heat setting (speed) according to your hair type. Use low speed for fine hair and high speed for thick hair.

What should I do if the power cord is damaged?

Do not use the appliance. Contact the manufacturer or an authorized service center for replacement to avoid hazard.

USER MANUAL SC-276 Scarlett

Line drawing of a SCARLETT robotic device (no text or symbols on the diagram itself)

www.scarlett.ru

GB DESCRIPTION

1. Housing
2. Air inlet
3. Hanging loop
4. Cord swivel protection
5. Attachment release knob
6. Speed control switch / Cool setting
7. Curling iron
8. Concentrator
9. Half round brush
10. Brushbarrel
11. Bristlebrush

CZ POPIS

- Please read this instruction manual carefully before use.

- Before connecting the appliance for the first time check that voltage indicated on the rating label corresponds to the mains voltage in your home.

- For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.

- Do not use outdoors.

- Always unplug the appliance from the power supply before cleaning and when not in use.

- Do not immerse the unit, cord or plug in water or other liquids. If it has happened, remove the plug from the wall socket immediately and have the unit checked by an expert before using it again.

- If the appliance is used in a bathroom, it should always be unplugged after use, because nearness of water is dangerous even if the appliance is switched off.

- For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.

- Do not spray aerosol products when the hair dryer is in operation.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliance.

- Do not leave the appliance switched on when you do not use it.

- Do not use other attachments than those supplied.

- Never carry or suspend the appliance by the cord.

- If the power cord is damaged it should be replaced by the manufacturer or authorized servicing center or qualified professional for safety reasons.

- Do not attempt to repair, adjust or replace parts in the appliance. Repair the malfunctioning appliance in the nearest service center.

- Keep the cord away from sharp edges and hot surfaces.

- If the product has been exposed to temperatures below 0^ C for some time it should be kept at room temperature for at least 2 hours before turning it on.

IMPORTANT:

- Keep your hair away from the immediate vicinity of the air inlet opening. Keep the air inlet filter dust and fluff free.

- Do not cover air inlet or air outlet otherwise the hair dryer may overheat.

- The attachments become hot during operation.

- The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes influence significantly the product safety, performance, and functions.

ATTENTION! Do not use the device beside the bathrooms, swimming pools and other vessels containing water.

INSTRUCTION FOR USE

- Fully unwind the cord.

- Attach the nozzle:

CONCENTRATOR

- The air concentrator is for bundling and directing the airflow for selective drying.

BRUSH BARREL (VOLUME FORMING)

- Divide your hair into locks and wind up on the brush barrel. Do not comb hair just after curling; let it cool down.

HALF ROUND BRUSH

- Attach the half round brush to the appliance. Set speed level of airflow and start to comb hair from roots to tips.

CURLING IRON

• Used to make curls and give volume to hair.
- Comb a hair lock and brush it several times from roots to ends.
- With a sliding movement twist the hair round the brush beginning with the hair ends.
- If your hair is long enough, finish with a full circle of the lock around the brush, up to the very hair roots.
- Hold the brush in this position for several seconds so that the lock gets fully warmed and obtains the desired shape and to give volume to your hair style by lifting the hair at the roots.
- Insert the plug into the power supply.
- Select desired speed mode using the speed switch. SPEED CONTROL
- Setting the speed level of airflow:

• 0 - off;
• 1 - "COOL SHOT" function for hair style fixing.
• 2 – medium speed for more delicate drying and styling;
• 3 – high speed for quick drying and styling.

- To prevent overheating do not work continuously longer than 10 minutes and obligatory stop the hair dryer for no less than 10 min.

- Always switch the appliance off and unplug when finished. Leave it to cool for a few minutes before putting away.

EASY ATTACHMENT REMOVAL BUTTON

- To remove an attachment fast and easily, press the attachment removal button.

CARE AND CLEANING

• Switch off the appliance, unplug it from the power supply and allow to cool fully.
• Do not use abrasive cleaners.

STORAGE

• Ensure that the hair dryer is completely cool and dry.
• Do not wrap the cord around the appliance, as this may cause damage.
• Keep the appliance in a cool, dry place.