3945 - Iron SUNBEAM - Free user manual and instructions

Product type	Steam Iron
Brand	Sunbeam
Model	3945
Power	120 V, 60 Hz
Soleplate	Non-stick with 21 steam holes and button grooves
Water tank	Fill hole with anti-spill cap
Steam functions	Variable steam and dry ironing
Spray	Spray Mist® trigger for localized dampening
Auto shut-off	Yes, after 15 minutes of inactivity
Power indicator	Red, turns off in auto shut-off
Reset button	Yes, red
Temperature control	Continuous with temperature guide
Cord	Swivel with heel wrap
Non-stick finish	Yes, non-stick coating
Warranty	2-year limited (according to conditions)
Maintenance	Clean soleplate with vinegar solution (1 tbsp vinegar per 250 ml water)
Safety	Do not immerse, unplug before filling, auto shut-off, do not leave unattended
Spare parts and repairability	Contact an authorized Sunbeam service center
General information	Manufactured by Sunbeam Products, Inc., Boca Raton, FL

Frequently Asked Questions - 3945 SUNBEAM

Why is my iron not heating up?

Check that the iron is plugged into a 120 V outlet. Make sure the temperature dial is set to the desired setting. If the red indicator is off, press the red reset button after auto shut-off.

Why is my iron not producing steam?

Check that the water tank is filled. Make sure the steam control is pressed in (steam position). Use a sufficient temperature setting (at least polyester). Let the iron preheat for 1 min 30 to 2 min. Tap the soleplate gently on the ironing board to unblock the valve.

Water flows from the steam holes, what to do?

Make sure the iron has reached the selected temperature before ironing (preheat for 1 min 30 to 2 min). If the iron is in dry mode, check that the steam control is in NO STEAM position. The tank may be too full: drain a little water. Let it cool, wipe, then reheat.

How to use the steam function?

Set the temperature control to MIN, place the top button in steam position, fill with water (see filling). Plug into 120 V. Set the temperature according to the fabric, wait 2 minutes for preheating. Once the temperature is reached, the iron produces steam. Use the Spray Mist® spray for localized dampening.

How to fill the water tank?

Always unplug the iron before filling. Place it on its heel rest. Open the anti-spill cap under the fill opening. Fill to the maximum level line. Close the cap and wipe the exterior. Do not overfill to avoid spills.

How to clean the iron soleplate?

Let the iron cool. Clean with a soft cloth and a slightly vinegar solution (1 tablespoon of vinegar per 250 ml water). Never use scouring pads, abrasive cleaners, or chemical solvents that could damage the non-stick coating.

What type of water to use in the iron?

This iron is designed for tap water. In hard water areas, use distilled water. Occasionally alternate with tap water to keep the iron in good condition. Do not use softened water (like from domestic softeners) as it contains minerals that can damage the appliance.

How does the auto shut-off work?

The iron turns off automatically after 15 minutes of inactivity when plugged in. The red indicator goes off to indicate power off. To restart, press the red reset button. Note that this does not replace the need to unplug the iron after use.

How to store the iron after use?

Set the temperature control to MIN and the steam control to OFF. Unplug the iron by pulling the plug. Empty the water from the tank while the iron is still warm. Let it cool completely on its heel rest. Wrap the cord loosely around the heel. Store it on its heel rest, never in its cardboard packaging.

What to do if the iron is not ironing correctly?

Check the temperature setting suited to the fabric. For mixed fabrics, use the setting for the fabric requiring the lowest temperature. In doubt, start with a minimum setting and test on a hidden area. If the iron drags or leaves marks, clean the soleplate and adjust steam.

USER MANUAL 3945 SUNBEAM

©2002 Sunbeam Products, Inc. All rights reserved. SUNBEAM® and SPRAY MIST® are registered trademarks of Sunbeam Products, Inc. Distributed by Sunbeam Products, Inc., Boca Raton, Florida 33431.

Line drawing of a sunbeam iron with a circular opening and handle, shown against a dark textured background (no text or symbols on the device itself)

MODEL/MODÈLE MODELO 3945

Instruction Manual 15-MINUTE AUTO-OFF STEAM IRON

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

Manuel d'Instructions FER À VAPEUR AVEC SYSTÈME D'ARRÊT AUTOMATIQUE APRÈS 15 MINUTES LIRE TOUTES LES INSTRUCTIONS ÀVANT D'UTILISER CET APPAREIL

When using your iron, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

1. Use iron only for its intended use.
2. To protect against risk of electric shock, do not immerse the iron in water or other liquids.
3. The iron should always be turned to "OFF" before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
5. Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.
6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
7. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.
8. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
9. If the iron is not operating normally, disconnect from the power supply and contact your nearest authorized Sunbeam distributor.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.

2. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

KNOW YOUR SUNBEAM® STEAM/SPRAY/DRY IRON

1. Temperature Control Dial
2. SPRAY MIST® Nozzle
3. Power Indicator/Reset Button
4. Water Fill Opening
5. Cord Wrap Groove
6. Steam On/Off Control
7. Non-Stick Sole Plate; 21 Steam Vents
8. SPRAY MIST® Trigger
9. Water Window
10. Fabric Temperature Suggestions
11. Heel Rest

FEATURES

• SPRAY MIST® – Provides a fine spray mist for spot dampening. Trigger control.
• Temperature Dial – Controls heat output of iron. Adjust dial according to ironing needs. For low temperatures, turn the dial to the first dot. For medium temperatures, turn the dial to second set of dots. For high temperatures, turn dial to third set of dots. (Refer to Ironing Guide for recommended settings).
• Swivel Cord – Pivots up and down and is supported to prevent dragging on fabric. Flexible grommet protects the cord from fraying.
• Soleplate – Has full-length button grooves for added convenience when ironing shirts and blouses.
• Non-Stick Finish – The non-stick coating on the soleplate prevents sticking of fabrics and starch residue.
• Sliding Water Reservoir Cover – Prevents dust and foreign matter from entering the water tank; stops any water spillage during ironing.
• Cord Wrap – Provides quick, convenient cord storage.
  • Automatic Shut-Off – Shuts off iron after 15 minutes of operation.
• Power Reset Button – Press to reset.

AUTO-OFF FEATURE

When the iron is plugged into a 120 V, AC electrical outlet, the steady red signal light signals the iron is on. If the iron is left standing for 15 minutes, the iron will stop heating. The signal light extinguishes to indicate auto shut-off and will stay out until the iron is either reset or unplugged.

To restart iron: To restart iron after it has shut itself off, please reset the red button.

CAUTION: DO NOT USE THE AUTO SHUT-OFF FEATURE AS A SUBSTITUTE FOR TURNING OFF AND UNPLUGGING THE IRON WHEN NOT IN USE.

BEFORE FIRST USE

To ensure no stain is transferred to the fabric the first time you use the iron, it is advisable to flush the soleplate steam vents to remove any residue from the manufacturing process. To do this:

1. Set the steam adjustment control to steam (on).
2. Fill the iron's water tank to its maximum fill line.
3. Set the temperature selector knob to its highest setting. Heat iron for 2 minutes.
4. Steam for 2 minutes while directing the steam vents away from the ironing surface.
5. Pass the iron on a damp cloth or a paper towel to clean.

SELECTING THE CORRECT FABRIC SETTING

When ironing, use the temperature and steam settings recommended for the type of fabric being ironed. Garments requiring low temperatures and steam should be ironed first. This will help avoid damaging garments with an iron that is too hot. If you are not sure of the fabric content of the garment, start with a low heat and steam setting and test the iron on an area of the garment where it will not show, such as a seam or facing. Gradually increase the heat and steam settings until wrinkles are removed without damaging the fabric.

When changing the temperature from a high setting to a lower setting (Example: Moving temperature selector from maximum to minimum), allow approximately 5 minutes for the lower temperature to be reached. The following charts are designed to help you select the best setting and method for the fabric you plan to iron. Check garment labels and follow recommendations given by the fabric manufacturer. For blended fabrics use the setting for the fabric in the blend requiring the lowest temperature. For example: 65% polyester, 35% cotton fabric. Iron this fabric at the minimum setting.

TEMPERATURE AND STEAM GUIDE

(All Models Except Variable Steam Models)

FABRIC

STEAM GUIDE

IRONING RECOMMENDATIONS

Acetate-Nylon Dry Steam Dry iron on wrong side while damp.

Acrylic-Silks Dry Steam Dry iron on wrong side while damp. Acrylic fabrics may be steam ironed at steam settings if fabric manufacturer directs.

Polyester Dry Steam Dry iron while fabric is damp or use spray as you iron. Iron rayon fabrics on the wrong side. Steam iron as fabric manufacturer directs.

Wools Dry Steam Steam iron on wrong side or use pressing cloth on right side.

Cottons Dry Steam Steam iron while damp or use spray as you iron. Iron dark fabrics on wrong side to avoid shine.

Linens Dry Steam Steam iron while damp or use spray as you iron. Iron each section until entirely dry. Iron dark fabrics on the wrong side and table linens on right side.

TEMPERATURE AND STEAM GUIDE

(All Models Except Variable Steam Models)

FABRIC

STEAM GUIDE

IRONING RECOMMENDATIONS

Acetate-Nylon MIN Dry iron on wrong side while damp.

Acrylic-Silks MIN Dry iron on wrong side while damp. Acrylic fabrics may be steam ironed at steam settings if fabric manufacturer directs.
Polyester	• Steam iron while fabric is damp or use spray as you iron. Iron rayon fabrics inside out. Steam iron as manufacturer directs.
Wools	• • Steam iron inside out or use pressing cloth on right side.

Cottons MAX Steam iron while damp or use spray as you iron.

...

Iron dark fabrics inside out to avoid shine.

Linens MAX Steam iron while damp or use spray as you iron. Iron each section until entirely dry. Iron dark fabrics inside out and table linens on right side.

A WORD ON WATER

This iron is specially designed to use tap water. In areas of the country where the water is very hard, distilled water is recommended for your iron. If you use distilled water in your iron, you should periodically use a tank of tap water to keep your iron properly conditioned. DO NOT use water passed through home water softening systems because such water contains minerals that may be harmful to the iron.

USING AS A DRY IRON

The iron can be used on the dry setting with or without water in the tank. Avoid having the tank too full of water while dry ironing.

• Slide the temperature control to MIN before plugging the cord into a 120 volt, AC electrical outlet.
• Slide top button to the no-steam position and move the temperature control to the appropriate fabric setting.
• If you are starting with a cool iron, let iron heat in the upright position on the heel rest. If the iron is already hot, be sure to cool or heat the iron to a suitable temperature for the fabric you are about to iron. Try it on an area of the garment where it will not show, such as a seam or facing.

USING AS A STEAM IRON

When using as a steam iron, be sure the temperature setting is within the STEAM range on the temperature selector to avoid water spotting the garment.

• Slide the temperature control to MIN. Slide top button to the steam position. Fill the iron with water. (See TO FILL THE WATER TANK instructions).
• Plug the cord into a 120 volt, AC electrical outlet.
• Move the temperature control to the appropriate fabric setting. Allow 2 minutes for the iron to reach the desired temperature.
• After iron has reached desired temperature, remove from the heel rest and use. If the unit fails to steam after depressing the steam slide button, gently tap the soleplate on the ironing surface. This will aid in starting the steaming action.
• When steam ironing, if the temperature control setting is accidentally lowered, water may appear on the soleplate, indicating that iron temperature has dropped below steaming level. If this should occur, reset temperature control to desired level. Rest the iron on its heel rest for 1 minute to allow it to reach temperature. If your iron starts losing its flow of steam and you wish to continue steam ironing, you may refill without cooling the iron. Unplug the iron. Follow the TO FILL THE WATER TANK instructions. Add water only to the maximum fill line to prevent overflow.

TO FILL THE WATER TANK

Always unplug the iron before filling. Set iron on its heel rest.

The water fill opening is located underneath the spill-proof cap. Hold the iron with the cap open and fill to maximum fill line. Close the spill-proof cap on the iron. Be sure the cap is fully sealed. Wipe the exterior of the unit to dry off any spillage.

TO EMPTY THE WATER TANK

Slide the temperature selector to the MIN position. Unplug the iron from the electrical outlet. Open the spill-proof cap. Holding the iron over the sink, point the iron handle down and hold in that position until water stops flowing out of the fill opening. Shake the iron gently to loosen trapped water drops; the heat of the iron will dry the inside of the iron. Let the iron cool on its heel rest.

IMPORTANT: SUNBEAM DOES NOT RECOMMEND STORING THE IRON WITH WATER IN THE TANK.

CARING FOR YOUR SUNBEAM IRON

• Avoid ironing over snaps, zippers, rivets on jeans, etc., as they will scratch the soleplate.
• FOR MODELS WITH A NON-STICK SOLEPLATE, clean water marks, calcium deposits and starch from the soleplate as follows: allow iron to cool and wipe with a soft cloth using a mild vinegar solution (one tablespoon of vinegar in one cup of water). DO NOT USE SCOURING PADS, ABRASIVES, OR CHEMICAL CLEANING SOLVENTS as they may mar the finish.

NOTE: Scratches in non-stick soleplates do not affect performance of iron.

MAINTENANCE

Other than recommended care instructions contained in this pamphlet, no further user maintenance should be necessary.

However, following is a list of frequently asked questions and their resolutions. If for any reason your Sunbeam iron continues to exhibit one of these symptoms, or should require repair for another reason, do not attempt to fix it yourself. Contact your authorized Sunbeam Distributor.

QUESTIONS AND ANSWERS

SYMPTOM/POTENTIAL REASONS AND SOLUTIONS

Iron does not heat

• Iron should be plugged into a 120 volt, AC electrical outlet only.
• The slide control must be set at the desired temperature.
• The auto shut-off feature may have been activated. Press the power reset button to start ironing.

Iron does not steam

• The water tank may be empty. Add water.
• Make sure the steam button is fully depressed. (On variable steam models, the slide control must be in one of the three steam positions).
• Use only temperature settings at or above Polyester.
• Do not set to steam setting until selected temperature has been reached. Make sure iron is pre-heated 1-1/2 - 2 minutes.
• Gently tap the soleplate on the ironing board once or twice to clear any blockage of steam valve.
• Your iron may spit or leak water from the steam vents if you try to get steam when the temperature setting is too low. Use only temperature settings in steam range shown on the Temperature and Steam Guide.

Iron spits water or leaks water from steam vents

• Make sure iron has reached selected temperature before ironing. Pre-heat iron 1-1/2 – 2 minutes.
• If the iron leaks when turned OFF or while DRY ironing, make sure the steam control is set to NO STEAM position.
• Iron may have been overfilled. Turn it off. Follow instructions for emptying the water tank. Remove some of the water. Let iron cool, then dry it off. Replug iron into electrical outlet and reheat. After 1-1/2 minutes, set to "steam". Follow USING AS A STEAM IRON instructions.

NOTE: Always set steam control to NO STEAM position unless unit is ready for steam ironing.

IRON STORAGE

• When you've finished ironing, turn the temperature guide to the MIN position and push down or slide the button to the OFF position.
• Remove the cord from the outlet by grasping the plug rather than pulling the cord.
• Empty the water tank AFTER EACH USE while the iron is still HOT.
• Allow the iron to COOL COMPLETELY before putting it away. Wrap the cord loosely around the heel rest. WRAPPING TOO TIGHTLY CAN DAMAGE THE CORD.
• Always store the iron ON ITS HEEL REST with the temperature control knob in the MIN position. DO NOT store in the carton, as any residue of moisture may cause the soleplate to discolor.

TWO-YEAR LIMITED HOSPITALITY WARRANTY

Sunbeam Products, Inc. ("Sunbeam") warrants that for a period of 2 years from the date of purchase, this product will be free from defects in material and workmanship. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty.

This warranty is valid for the original purchaser from the date of initial purchase and is not transferable. Sunbeam dealers, service centers, or stores selling Sunbeam products do not have the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than Sunbeam or an authorized service center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.

Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.

How to Obtain Warranty Service

Contact your Sunbeam authorized dealer.

DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE

PRÉCAUTIONS IMPORTANTES

SYMPTOME/CAUSES POSSIBLES ET SOLUTIONS

Always unplug the iron before filling. Set iron on its heel rest.

The water fill opening is located underneath the spill-proof cap. Hold the iron with the cap open and fill to maximum fill line. Close the spill-proof cap on the iron. Be sure the cap is fully sealed. Wipe the exterior of the unit to dry off any spillage.

PARA VAZIAR O DEPÓSITO DE ÁGUA

PERGUNTAS E RESPOSTAS

SINTOMAS/POSSÍVEIS CAUSAS E SOLUÇÕES