MLC-2702G - Monitor DENVER - Free user manual and instructions

Product Type	Monitor
Brand	Denver
Model	MLC-2702G
Screen Size	27 inches (estimated)
Resolution	1920 x 1080 (Full HD)
Aspect Ratio	16:9
Connectivity	2x HDMI, 1x DisplayPort
VESA Mount	75 x 75 mm
Power Input	AC power (cable included)
Stand	Included, detachable (press button to release)
OSD Menu	Yes, via M button
ECO Modes	Standard, Text, Movie, Game, FPS, RTS
Gameplus Feature	On-screen crosshairs for aiming
LED Indicator	Solid blue (on), flashing blue (no signal), red (no sync/low voltage)
Buttons	Power, M (menu), Up, Down, E (exit/color gamut)
Included Accessories	Power cable, DP cable, stand parts, screws for stand and VESA mount
Cleaning	Wipe with dry cloth; avoid liquid cleaners
Safety	Use surge protector; ensure proper ventilation; do not disassemble
Disposal	WEEE compliant; do not dispose with household waste

Frequently Asked Questions - MLC-2702G DENVER

How do I connect the monitor to my computer?

Use either an HDMI cable or DisplayPort cable. Connect one end to your computer's graphics card and the other to the corresponding port on the monitor. Then plug in the power cable and press the power button.

How do I change the input source?

Press the M button to open the OSD menu. Navigate to the input source option using the Up/Down buttons, select the desired input (HDMI1, HDMI2, or DP), and press the M button to confirm.

How do I adjust brightness or contrast?

Press the M button to open the OSD menu. Use the Up/Down buttons to navigate to the brightness/contrast settings, then adjust with Up/Down and confirm with M. Press E to exit.

How do I install the stand?

1. Place the monitor face-down on a soft surface. 2. Attach the stand plate to the stem using the provided 12mm screws, then attach the base to the stem with the 14mm screw. 3. Insert the stand plate into the slot on the back of the monitor until it clicks.

Can I mount this monitor on a VESA arm?

Yes, the monitor supports a 75x75mm VESA mount. Remove the original screws from the back, attach the mounting bracket using the included NO.2 screws (30mm x2 and 26mm x2), then follow your VESA mount's instructions. Note: the VESA mount is not included.

What do the LED indicator lights mean?

- Solid blue: monitor is on and functioning normally. - Flashing blue: no video source detected. - Red: no horizontal/vertical signal or low voltage. Ensure your computer is on and cables are properly connected.

How do I switch between ECO modes?

Press the ▲ button to cycle through ECO modes: Standard, Text, Movie, Game, FPS, and RTS. Choose the mode that best suits your activity.

How do I use the Gameplus crosshairs?

Press the ▼ button repeatedly to cycle through Gameplus icons. Select a crosshair icon to overlay an aiming reticle on the screen during games.

How do I detach the stand?

Lay the monitor face-down on a flat surface. Press the button located near the stand plate on the back of the monitor, then slide the stand out. Do not force it.

What should I do if the monitor displays 'No Signal'?

Check that the video cable (HDMI or DP) is securely connected to both your computer and the monitor. Ensure your computer is powered on. Try switching input sources via the OSD menu. If using a desktop, verify the graphics card is properly seated.

USER MANUAL MLC-2702G DENVER

Modern flat-screen monitor with a metallic stand and tripod base (no text or symbols visible)

Read this booklet thoroughly before using and save it for future reference

Section 1: Product Overview

1.1 - Monitor Buttons

1 : Insert the power cable to supply power to the monitor. Power Connector

2 : Press to display the OSD menu or enter sub-menus. M Menu Button

3 ▼Press to move down in the menus. Down Button

4 ▲Press to move up in the menus. Up Button

5 : Press to exit. E Exit Button

6 Power Button: Press to turn the monitor on/off.

7 : Changes colors to indicate status. Refer to Section 6. LED Indicator

The E button can also be used to switch between two color gamuts when a compatible graphics card and either HDMI or DP connections are in use.

1.2 - Monitor Ports

8 HDMI 1 Connector: Insert one end of the HDMI cable into the computer's HDMI output and connect the other end to the monitor's HDMI port.

9 HDMI 2 Connector: Insert one end of the HDMI cable into the computer's HDMI output and connect the other end to the monitor's HDMI port.

10 DP Connector: Insert one end of the DP cable into the computer's DP output and connect the other end to the monitor's DP port.

Section 2: Stand Installation

Keep the foam over the monitor before attaching the stand. Follow the steps below to finish the installation.

1. Open the package, take out the product with foam still attached, and gently place it on a desktop or table.

1. Take out the two parts of the stand, remove the foam covering the back of the monitor, and press the button to remove the stand plate.

1. Use the screwdriver and two 12mm NO.1 screws to fasten the stand plate to the stem. Next, use the remaining 14mm stand screws to fasten the base to the stem.

1. Insert the stand's plate into the opening on the back of the monitor. It should click into place. Make sure the stand is securely attached to the back of the monitor then remove the monitor from the remaining foam section and stand it up on a table or desk as desired.

If needed, the stand can easily be detached from the monitor by pressing the button near the stand plate. Make sure the monitor is laid on a flat surface before removing the stem.

Eng-4

Section 3: Mount Installation

This monitor ONLY includes screws which may be used when attaching the monitor to a VESA 75x75mm type mount. No VESA mount or mounting accessory is included.

1. Open the package, take out the product with foam still attached, and gently place it on a desktop or table. If the monitor is attached to the stand, remove the stand.

1. Take out the two parts of the stand, remove the foam covering the back of the monitor, and press the button to remove the stand plate.

1. Remove the original screws x 4 ( ) from the opening in the back of the monitor, then use the NO. 2 screws provided to secure the rear panel.

2. Follow the directions received with your VESA mount stand or accessory and install the monitor on the wall or fixture as desired. Remember to use the included NO. 2 screws when attaching anything to the back of the monitor. Refer to the image (2) for correct screw placement when attaching the monitor to a mount.

Simple line drawing of a monitor with a circular icon and pointer, no text or symbols present

Use the 30mm -NO. 2 Screws x 2 -Use the 26mm NO. 2 Screws x 2

- Use only the NO. 2 Screws (30 mm x 2 pcs, 26mm x 2 pcs) provided with this type of installation.

- Do not discard the original screws as these may be needed for future use.

Simple geometric diagram with a rectangle inside a square, no text or symbols present

Eng-5

Section 4: Connectivity Options

4.1 - Removing the Port Cover

Before connecting any cables, remove the port cover first.

4.2 - Connecting the Power Cable

Connect the included power cable to the power connector, and then plug the other end into an wall outlet.

4.3 - DP Connectivity

In order for the monitor to receive DP signals from the computer, use the DP cable to connect the monitor to the computer.

Section 5: Basic Operation

1. Insert one end of the DP cable into your PC's graphics card.

For optimal refresh rate (or "performance"), it is recommended to use a DP cable with the monitor's corresponding connector.

1. Connect the other end of the cable to the corresponding connector on your monitor. See the image below.

1. Connect the power cable to your monitor then connect the other end to your power source. It is recommended that you use a surge protector with adequate voltage if a wall outlet cannot be reached directly.

2. Locate the power button on the monitor and press it to turn the monitor on.

If you cannot locate the power button, please refer to Section 1.1.

Section 6: Indicator Light

This light is located on the bottom of the monitor.

Bottom View

Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light indicates no video source has been detected. Red light indicates that no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/or connected.

Section 7: ECO Modes and Gameplus Switching

1. Press any one of the buttons (M, .▼, ▲) to activate the navigation window.

Blue background with five black-and-white icons: home, game controller, car, grid, and power button (no text or labels)

1. Press ▼button to switch Gameplus modes. According to the needs of your game, choose the corresponding game icon. These game icons are primarily designed to optimize your aim during shooting games, though they can be used for other scenarios.

1. Press ▲button to switch ECO modes. These modes include Standard, Text, Movie, Game, FPS and RTS modes and can be used to optimize settings according to your activity. Standard mode is suitable for most activities.

DENVER®

www.denver-electronics.com

Symbol of a trash bin crossed out by two diagonal lines (no text or numbers present)

Electric and electronic equipment contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment) is not handled correctly.

Electric and electronic equipment is marked with the crossed out trash can symbol, seen below. This symbol signifies that electric and electronic equipment should not be disposed of with other household waste, but should be disposed of separately.

All cities have established collection points, where electric and electronic equipment can either be submitted free of charge at recycling stations and other collection sites, or be collected from the households. Additional information is available at the technical department of your city.