OHDV 7 EX - Tumble dryer Otsein-Hoover - Free user manual and instructions

Product Type	Tumble Dryer
Brand	Otsein-Hoover
Model	OHDV 7 EX
Capacity (Max Load)	7 kg (Cottons) / 3 kg (Synthetics)
Drum Capacity	115 litres
Dimensions (Height x Width x Depth)	85 cm x 60 cm x 60 cm
Energy Label	Band C
Electrical Supply	220–240 V, 50 Hz (typical)
Plug Type	Moulded-on non-rewireable plug (earthed)
Drying Programs	Bone Dry, Extra Dry, Cupboard Dry, Iron Dry, Medium Dry, Damp Dry, Timed Drying (30–75 min), Pre-Iron (Planchado Rápido)
Fabric Types	Cottons, Synthetics, Delicates
Heat Settings	High and Low (selectable via 'CLASE TEJIDOS' button)
Drying Sensor	Automatic sensor that stops drying when load is dry
Delay Start	Up to 9 hours (MARCHA DIFERIDA)
Creaseguard Function	Intervals every 15 minutes after cycle end
Filter Indicator	LIMPIEZA FILTRO light alerts when filter needs cleaning
Cooling Period	10 minutes of cool air at end of cycle
Buzzer / Alarm	Audible end-of-cycle signal; can be disabled via 'NO ALARMA' button
Venting	Venting hose included (95 mm diameter, up to 1.8 m length)
Maintenance	Clean filter after each cycle; clean sensor plate with vinegar solution periodically
Safety Features	Overheat protection? (not explicitly stated; safety reminders include warnings about fluff and proper installation)
Service	Repairs by GIAS Service or authorised dealer; special supply cord only from GIAS

Frequently Asked Questions - OHDV 7 EX Otsein-Hoover

What is the maximum drying capacity of the OHDV 7 EX?

The maximum load is 7 kg for cottons and 3 kg for synthetics. Do not overload the drum; large wet items like duvets may exceed the max capacity.

How do I clean the fluff filter?

After each cycle, pull the filter upward, open it, and gently remove lint with a soft brush or fingertips. Snap it closed and push back into place. The LIMPIEZA FILTRO indicator lights when cleaning is needed.

Why are my clothes not drying completely?

Possible causes: incorrect program selection, clothes too wet, clogged filter, blocked venting hose, overloaded drum, or a small load (use timed programs for small loads). Also check that the sensor plate is clean.

Can I delay the start of the drying cycle?

Yes, press the MARCHA DIFERIDA button to delay start by up to 9 hours. The display shows the delay time; press START to confirm. The delay counts down and the dryer starts when it reaches 0.

What does the 'PLANCHADO RÁPIDO' (Pre-Iron) program do?

This program heats the load for 9 minutes followed by a 3-minute cool down to relax creases, making ironing easier. It's useful for garments left in a basket or stiffened after line drying.

How do I clean the sensor plate?

The sensor plate is inside the drum below the door opening. Wipe it with a soft cloth and a dilute vinegar solution. Remove any excess to avoid staining clothes. Clean periodically to ensure proper sensor operation.

What should I do if the dryer does not start?

Check the power supply, plug connection, and fuse. Ensure the door is fully closed, the dryer is switched on, and a program is selected. Press the START button. If a delay is set, wait for the countdown to finish.

Can I tumble dry woollens or delicate fabrics?

No, woollens, silk, delicate fabrics, nylon stockings, and items with PVC or leather trimmings should not be tumble dried. Use the low heat setting (CLASE TEJIDOS button) for delicates, but avoid items marked 'do not tumble dry'.

How should the dryer be ventilated?

The dryer must be vented to the outside using the supplied hose (95 mm diameter, max 1.8 m). Ensure the hose is not kinked and the external outlet is protected from wind. The air inlets and outlets must not be obstructed; maintain at least 12 mm gap around the machine.

What should I do if the power cord is damaged?

The supply cord must be replaced by a special cord available only from GIAS Service or an authorised dealer. Do not use the appliance with a damaged cord.

USER MANUAL OHDV 7 EX Otsein-Hoover

Empty white rectangle with corner markers and no text or symbols

Empty white rectangle with corner markers, no text or symbols present

ENGLISH

Safety Reminders

WARNING Check that the product has no visible signs of damage before use. If damaged do not use and please contact GIAS Service.

WARNING Do not use the product if the fluff filter is not in position or is damaged; fluff could be ignited.

WARNING Foam rubber materials can, under certain circumstances, when heated become ignited by spontaneous combustion. Foam plastic, foam rubber and rubber-like material are not suitable for tumble drying. Articles made from these materials MUST NOT be placed in the dryer.

Always refer to the laundry care labels for directions on suitability for drying.

WARNING Misuse of a tumble dryer may create a fire hazard.

WARNING Where the hot surface symbol is located the temperature rise during operation of the tumble dryer may be in excess of 60^ C.

User's manual. This machine should only be used for its intended purpose as described in this manual. Ensure that it is fully understood before operating.

Installation. This machine should not be installed in a bathroom or shower room.

Never install the dryer against curtains and be sure to prevent items from falling or collecting behind the dryer.

Ventilation. Adequate ventilation must be provided in the room where the tumble dryer is located to prevent gases from appliances burning other fuels, including open fires, being drawn into the room during operation of the tumble dryer.

Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels.

Check regularly that the air flowing through the dryer is not restricted:

Check the fluff filter after use, and clean, if necessary.

The venting hose or duct should be checked periodically and any accumulation of fluff removed.

The inlet and outlets should be kept free from obstructions.

If the dryer is used frequently the period between checks should be reduced accordingly.

Dryness. Clothes should be spin dried or thoroughly wrung before they are put into the tumble dryer. Clothes that are dripping wet should NOT be put into the dryer.

Lighters and matches must not be left in pockets and NEVER use flammable liquids near the machine.

Glass fibre curtains should never be put in this machine. Skin irritation may occur if other garments are contaminated with the glass fibres.

Garments treated or contaminated with flammable cleaning sprays or liquids such as petrol, cooking oil or aerosol sprays must not be put in this machine.

Lint or fluff must not be allowed to collect on the floor around the outside of the machine.

Cool down period. The drum inside may be very hot. Always allow the dryer to complete the cool down period before removing the laundry.

Faults. Do not continue to use this machine if it appears to be faulty.

After use. Remove the plug from the electricity supply. Always remove the plug before cleaning the appliance.

Supply cord. If the supply cord on this appliance is damaged, it must be replaced by a special cord which is only available from GIAS Service or an authorised dealer.

GIAS Service. To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised service engineer.

ENGLISH

Safety reminders 2 Opening the door 6

Electrical requirements 3 Filter 6

Ventilation requirements 4 Drying guide 7

Preparing the load 5 Controls & indicators 8

Clothes preparation 5 Operation 9-10

Maximum drying weight 5 Cleaning the dryer 10

Sorting the load 5 Technical specification 10

Do not tumble dry 5 Trouble shooting 11

Energy saving 5

PLEASE READ THESE INSTRUCTIONS THOROUGHLY

This appliance must be operated in accordance with the instructions given in this manual. It is for domestic use only in drying household textiles and garments where a water solution has been used in the cleaning process. It MUST NOT be used with dry cleaning fluids. For your safety, this dryer must be correctly installed.

If there is any doubt about installation, call GIAS Service for advice.

Before using the tumble dryer for the first time:

• please read this instruction book thoroughly.
• remove all items packed inside drum.
• wipe the inside of the drum and door with a damp cloth to remove any dust which may have settled in transit.

IMPORTANT: This dryer must only be used for drying household textiles and garments where a water solution has been used for the cleaning process.

DO NOT tumble dry fabrics treated with dry cleaning fluids.

Electrical requirements

WARNING!

ELECTRICITY CAN BE EXTREMELY DANGEROUS. THIS APPLIANCE MUST BE EARTHED.

This appliance is fitted with a moulded-on non-rewireable plug.

The plug should be accessible for disconnection after the appliance has been installed.

IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:

Blue - NEUTRAL

Brown - LIVE

Green-and-yellow - EARTH

If the supply cord on this appliance is damaged, it must be replaced by a special cord which is only available from GIAS Service or an authorised dealer.

ENGLISH

Installation and Ventilation requirements

IMPORTANT: This dryer must be installed such that the air inlets and outlets are not restricted (fig. 1).

There should be a gap of at least 12 mm (0.5 inches) between the sides and rear of the machine and the surrounding walls and cabinets.

To ensure adequate ventilation the space between the bottom of the machine and the floor must not be obstructed.

NEVER install the dryer up against curtains.

Prevent items from falling or collecting between the sides and rear of the dryer as these may obstruct the air inlet and outlets.

A venting hose is supplied with this tumble dryer.

The use of the venting hose to exhaust hot air to the external atmosphere is strongly recommended to ensure

maximum drying efficiency. Protect the external outlet from prevailing winds to ensure back-draughts do not reduce the drying performance.

If the dryer is installed under a worktop or built-in, it is essential to use the venting hose to carry the hot moist air away from the dryer otherwise re-circulation of the moist air will prevent the dryer from working efficiently.

The hose may be fitted through a wall or through an open door or window (fig. 2). The hose is 95 mm (3.75 inches) in diameter and will extend up to 1.8 metres (6 feet).

Venting hoses longer than 1.8 metres (6 feet) are not recommended as the dryer performance will be reduced.

Ensure that the venting hose is not kinked as this will prevent the dryer from working efficiently.

There are three air outlets – one at the rear and one on each side of the dryer. The venting hose must only be attached to one of these outlets. The covers must be fitted to the two unused outlets to maintain maximum drying efficiency.

ENGLISH

Preparing the load

Before using the dryer for the first time wipe the inside of the drum and door with a damp cloth.

Make sure that the laundry you are going to dry is suitable for drying in a tumble dryer, as shown by the care symbols on each item.

Clothes preparation

Check that all fastenings are closed and that pockets are empty. Turn the articles inside out. Place clothes loosely in the drum to make sure that they don't get tangled.

Warning: Do not overload the drum, large items when wet can exceed the maximum admissible clothes load (for example: sleeping bags, duvets).

Maximum drying weight

●Cottons Max. 7 kg

●Synthetics Max. 3 kg

Sort the load as follows:

A) By care symbols

On the collar or inside seam:

Suitable for tumble drying.
● Tumble drying at high temperature.
Tumble drying at low temperature only.
DO NOT tumble dry.

B) By amount and thickness

Whenever the load is bigger than the dryer capacity, separate clothes according to thickness (e.g. towels from thin underwear).

C) By type of fabric

Cottons/linen: Towels, cotton jersey, bed and table linen.

Synthetics: Blouses, shirts, overalls, etc. made of polyester or polyamid, as well as for cotton/synthetic mixes.

D) By drying level

• Sort into: Iron dry, cupboard dry, etc.
• For delicate articles press the 'CLASE TEJIDOS' button to select low drying temperature.

Do not tumble dry:

Woollens, silk, delicate fabrics, nylon stockings, delicate embroidery, fabrics with metallic decorations, garments with PVC or leather trimmings, training shoes, bulky items such as sleeping bags, etc.

IMPORTANT: Do not dry articles which have been treated with a dry cleaning fluid or rubber clothes (danger of fire or explosion).

Energy saving

Only put into the tumble dryer laundry which has been thoroughly wrung or spin-dried. The drier the laundry the shorter the drying time thus saving electricity.

ALWAYS try to dry the maximum weight of laundry, this will save time and electricity.

NEVER exceed the maximum weight, this will waste time and electricity.

ALWAYS check that the filter is clean before every drying cycle.

NEVER put dripping wet items into the tumble dryer, this may damage the appliance.

ALWAYS ensure that the covers are fitted to the two unused vent outlets, this will maintain maximum drying performance.

ENGLISH

Opening the door

Pull on handle to open the door (fig. 3).

Line drawing of a hand holding a fan inside a device panel (no text or symbols)

To restart the dryer, close the door and press the 'START' button.

WARNING! WHEN THE TUMBLE DRYER IS IN USE THE DRUM AND DOOR MAY BE VERY HOT.

Filter

IMPORTANT: To maintain the efficiency of the dryer check that the fluff filter is clean before each drying cycle.

Line drawing of a car interior showing hand placing a component into the window (no text or symbols)

1. Pull the filter upwards (fig. 4).

2. Open filter as shown (fig. 5).

Technical line drawing of a mechanical assembly with hands operating a component (no text or symbols)

1. Gently remove lint using a soft brush or your fingertips.

2. Snap the filter together and push back into place.

Filter Care Indicator (LIMPIEZA FILTRO)

Lights when the filter needs cleaning. If the laundry is not drying check that the filter is not clogged. The indicator will also light when the venting hose is blocked or kinked.

ENGLISH

Drying guide

Programme Drying Guide
1 Bone Dry
2 Extra Dry
3 Cupboard Dry
4 Iron Dry
5 Medium Dry
6 Damp Dry

For delicate fabrics select the 'CLASE TEJIDOS' button for all Drying Programmes. This reduces the drying temperature to protect your garments.

PRE-IRON PROGRAM: RELAXES CREASES – EASIER TO IRON

REMEMBER: During the last 10 minutes the load is always tumbled in cool air.

ENGLISH

Control panel and indicator lights

1. 'ON/OFF' button and indicator – press to switch on, the indicator will light. Press again to switch off, the indicator will go out.
2. 'CLASE TEJIDOS' button – press to reduce the heat level for delicate items, press again to select high temperature. This function is available on all programmes.

HIGH Heat setting

LOW Heat setting

1. 'NO ALARMA' button – press to stop the buzzer.
2. 'DIGITAL DISPLAY' shows the number of hours delay remaining when 'MARCHA DIFERIDA' (START DELAY) is selected.
3. 'PROGRAM' dial – selects drying program.
4. 'LIMPIEZA FILTRO' indicator – lights when filter needs cleaning.
5. 'COOLING' indicator – lights when the drying cycle is in the cooldown period.
6. 'HEATING' indicator – lights when the drying cycle is in the heating period.
7. 'START' button – press to start the drying cycle.
8. 'MARCHA DIFERIDA' button – press to delay the start of the drying cycle by up to 9 hours.

ENGLISH

Operation

1. Open the door and load the drum with laundry. Ensure that garments do not hinder closure of the door.

2. Gently close the door pushing it slowly until you hear the door 'click' shut.

3. Press the 'ON/OFF' button to switch on the dryer. The indicator will light.

4. Turn the program dial to select the required drying program:

e.g. if you are drying cotton laundry and would like it suitable for ironing please select the iron dry option.

The PLANCHADO RÁPIDO setting shown by the symbol 📋 on the program dial provides a conditioning and anti-crease function. The dryer will heat the load for 9 minutes followed by a 3 minute cool down period and is especially good for garments which may have been left for some time prior to ironing, in a linen basket for example. Garments may also become stiffened when dried outside on a washing line or inside on radiators. The PLANCHADO RÁPIDO process relaxes the creases in the fabric making ironing quicker and easier.

1. If drying delicate items on the 'timed' programs press the 'CLASE TEJIDOS' button to reduce the heat level. Press again on completion, to select high temperature.

HIGH Heat setting LOW Heat setting

1. Press the 'START' button. The dryer will start automatically and the 'HEATING' indicator will light.

Drying sensor

A sensor will detect when the load is dry. The drying cycle will then go into the cooldown period and the 'COOLING' indicator will light.

After 10 minutes of cooldown the drum will stop rotating automatically.

Note:

(i) The sensor may not detect a small load of small articles. For small loads and separate items or pre-dried fabrics with low moisture content, utilise the timed programs. Set the program between 30 and 75 minutes depending upon load size and dryness required and select high or low heat depending upon the fabric type. If this is not carried out the dryer will only operate for 10 minutes before going into cooldown.

(ii) If the sensor does not operate, for example when a load is too large or too wet to tumble dry, the dryer will automatically go into cooldown after 180 minutes.

The dryer can be set to start up to 9 hours after the program has been set.

To set the time delay option press and release the 'MARCHA DIFERIDA' button until the required delay (shown in hours) appears on the display and then press the 'START' button. The display will flash.

As each hour passes the figure shown on the display will count down. When it gets to 0 the dryer will start.

The delay can be changed at any time simply by pressing the button until the new figure appears on the display.

If there is an interruption to the electricity supply the time delay will be lost and so will have to be re-set when the power is restored.

1. To switch off the buzzer, which sounds at the end of each cycle, press the 'NO ALARMA' button.

2. The load is dried by tumbling in thermostatically controlled warm air. Cool air is used for the last 10 minutes to reduce creasing and cool the load

ENGLISH

ready for handling. During this time the 'COOLING' indicator is lit.

1. When the program is fully completed the drum will stop rotating. The dial remains at the position of the selected program. The 'COOLING' indicator will flash and the buzzer will sound.

2. Open the door and remove the load.

WARNING! THE DRUM, DOOR AND LOAD MAY BE VERY HOT.

If the load is not removed from the dryer at the end of the drying cycle, a 'creaseguard' function is activated. Every 15 minutes the dryer will tumble the load for 5 seconds and the buzzer will sound.

This process will be repeated until the 'creaseguard' function is cancelled by opening the door.

The ‘COOLING’ indicator will continue to flash while ‘creaseguard’ is activated.

1. Clean the filter after every drying cycle to ensure maximum dryer efficiency. (See 'Filter' section.)

Cleaning the dryer

IMPORTANT: Always switch off and remove the plug from the electricity supply before cleaning this appliance.

Clean the filter after every drying cycle.

After each period of use, wipe the inside of the drum and leave the door open for a while to allow circulation of air to dry it. Wipe the outside of the machine and the door with a soft cloth.

DO NOT use abrasive pads or cleaning agents.

To prevent the door sticking, periodically clean the door gasket with a 'non-scratch cream cleaner.'

Over a period of time deposits from the water may form over the sensor plate (found inside the drum below the door opening). This sensor plate can be cleaned with a soft cloth and a dilute vinegar solution. Ensure that any excess is removed or the vinegar solution may stain clothing.

Technical specifications

Drum capacity 115 litres

Maximum load 7 kg

Height 85 cm

Width 60 cm

Depth 60 cm

Energy Label Band C

Note: For electrical data refer to the rating label on the front of the dryer cabinet (with the door open).

ENGLISH

Trouble shooting

Should your dryer operate incorrectly, check the following points before calling for a service engineer.

Drying time is too long/clothes are not dry enough:

●Have you selected the correct drying time/program? Go to page 7.
●Were the clothes too wet? Were the clothes thoroughly wrung or spin-dried?
- Does the filter need cleaning? Go to page 6.
●Is the dryer overloaded? Go to page 5.
●Is the venting hose kinked or blocked? Go to page 4.
●Is the load too small? Go to page 9-10.
- Has the ‘CLASE TEJIDOS’ option been selected from a previous cycle? Go to page 8.
●Is the sensor system clean? Deposits from the water may form over the sensor plate. Go to page 10 “Cleaning the dryer”.

The dryer does not operate:

●Is there a working electricity supply to the dryer? Check using another appliance such as a table lamp.
●Is the plug properly connected to the mains supply?
●Is there a power failure?
●Has the fuse blown?
●Is the door fully closed? Go to page 9-10.
●Is the dryer switched on, both at the mains supply and at the machine? Go to page 8.
●Has the drying time or the program been selected? Go to page 8.
●Have you pressed the 'START' button to begin the program? Go to page 9-10.

• Has the ‘MARCHA DIFERIDA’ option been set and is there still time remaining? Go to page 9-10.
  ●Has the 'START' button been pressed after opening the door? Go to page 6.

Filter Care Indicator on

• Does the filter need cleaning? Go to page 6.
  ●Is the venting hose kinked or blocked? Go to page 4.

If the supply cord on this appliance is damaged, it must be replaced by a special cord which is only available from GIAS Service or an authorised dealer.

Should there still be a problem with your dryer after completing all the recommended checks, please call Service for advice. They may be able to assist you over the telephone or arrange for a suitable appointment for an engineer to call under the terms of your guarantee. However, a charge may be made if any of the following applies to your machine:

●Is found to be in working order.
●Has not been installed in accordance with the installation instructions.
●Has been used incorrectly.

DEUTSCH

Sicherheitshinweise

Line drawing of a hand holding a fan inside a door, with no text or symbols present

Line drawing of a car interior showing hand placement inside a vehicle door (no text or symbols)

Technical line drawing of a mechanical assembly with hands operating a component (no text or symbols)

ESPAÑOL

Line drawing of a hand holding a fan inside a device panel (no text or symbols)

Line drawing of a car interior showing hand placement inside a vehicle door (no text or symbols)

Illustration of hands assembling a rectangular panel or device (no text or symbols visible)

Line drawing of a hand holding a fan inside a device panel (no text or symbols)

Line drawing of a car interior showing hand placement inside a vehicle (no text or symbols)

1. Puxe o filtro para cima (fig. 4).
2. Abra o filtro como ilustrado (fig. 5).

Illustration of hands assembling a mechanical component with no visible text or symbols

Empty white rectangle with corner markers, no text or symbols present

Back Page.fm Page 39 Tuesday, August 26, 2003 4:54 PM

40000489 © 2001 ® REGISTERED TRADE MARK