BERLIN088-4RVA++ - Refrigerator Frilec - Free user manual and instructions

Product Type	Refrigerator
Brand	Frilec
Model	BERLIN088-4RVA++
Climate Class	SN (10°C to 32°C), N (16°C to 32°C), ST (16°C to 38°C), T (16°C to 43°C)
Temperature Control	Thermostat with 8 settings: 1 (warmest) to 7 (coldest), 0 (off)
Defrosting	Manual defrost required
Interior Light	LED (replaceable by qualified technician)
Door Reversibility	Yes, instructions included
Installation Type	Built-in (with installation kit provided)
Refrigerant	R-600a (isobutane), flammable
Safety Features	Child lock, warnings for flammable refrigerant, electrical safety
Cleaning	Warm water and neutral soap; no abrasive cleaners
Storage Guidance	Do not store hot food; wrap strong-smelling food; store raw meat separately
Energy Saving Tips	Avoid frequent door opening; remove drawers for more space; set appropriate temperature
Accessories	Movable shelves, door balconies, installation kit (guides, sliders, screws, rubber seal)

Frequently Asked Questions - BERLIN088-4RVA++ Frilec

How do I set the temperature on my Frilec BERLIN088-4RVA++ fridge?

Plug in the appliance. The thermostat has 8 settings: 1 is the warmest, 7 is the coldest, and 0 turns off the appliance. Adjust the knob to your desired temperature. If the appliance is in a hot location or the door is opened often, it may not maintain the set temperature.

Can I reverse the door opening direction?

Yes, the door is reversible. You will need a Philips and flat bladed screwdriver. Tilt the unit back, remove the top hinge, lift off the door, then unscrew the bottom hinge. Move screw holes from left to right, install the top hinge on the bottom left, place the door back, and install the bottom hinge on the top left. Ensure the seal closes properly.

How should I clean the refrigerator?

Disconnect the appliance from the power supply. Remove all food. Clean the interior and accessories with a cloth and lukewarm water and neutral soap. Do not use abrasive cleaners or steam cleaners. After cleaning, wipe with fresh water and dry thoroughly before reconnecting.

What should I do if the refrigerator is not cooling?

Check that the temperature knob is not set to 0. Ensure the mains plug is firmly inserted and the fuse is intact. If the socket is defective, contact an electrician. Also, check that the door is not left open and that the appliance is not near a heat source.

What does the climate class mean?

The climate class indicates the range of ambient temperatures in which the fridge operates efficiently. This model supports SN (10°C to 32°C), N (16°C to 32°C), ST (16°C to 38°C), and T (16°C to 43°C). Install the appliance in a location that matches your climate.

How do I replace the interior light bulb?

The internal light is an LED type. Do not attempt to replace it yourself. Contact a qualified technician for replacement.

Can I store hot food in the refrigerator?

No, you should not store warm food or evaporating liquids in the refrigerator. Allow hot food to cool to room temperature before placing it inside to maintain efficient operation and prevent damage.

Is the refrigerator safe for children?

Yes, but with supervision. Children aged 8 years and above can use the appliance if instructed properly. Children aged 3 to 8 can load and unload it. Always keep packaging away from children to avoid suffocation, and when discarding the appliance, remove the door to prevent entrapment.

How do I defrost the freezer compartment?

Defrost manually. Switch off the appliance and remove all food. Leave the door open to allow frost to melt. Do not use mechanical devices or sharp objects to remove frost. Use a plastic scraper if necessary. After defrosting, clean and dry the interior.

What are some energy-saving tips?

Avoid opening the door frequently or for long periods. Do not set the thermostat to excessively cold temperatures. Remove accessories like drawers if you need more space, as this can lower energy consumption. Ensure food does not touch the back wall and allow air circulation.

USER MANUAL BERLIN088-4RVA++ Frilec

Simple line drawing of a table with a handle and hanging chain (no text or symbols)

Pure technical line drawing of a structural bracket with a small mounting bracket (no text or symbols)

Technical line drawing of a mechanical component with a curved top and base, showing motion direction (no text or symbols)

Technical line drawing of a structural bracket with mounting base (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Installatie

Isometric diagram of a door with two arrows indicating direction (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Simple line drawing of a table frame with a curved arrow indicating rotation (no text or symbols)

Diagram showing a curved pipe or duct with an arrow indicating direction, enclosed in a circular inset (no text or symbols)

Positie

Line drawing of a hand holding a shelf with shelves (no text or symbols)

Simple diagram of a container with two upward arrows indicating flow or movement (no text or symbols)

Diagram of a mechanical or electrical component with arrows indicating motion, no text or symbols present

White rectangular cabinet or enclosure with no visible text or symbols on its surface

Exploded view diagram of electronic components including a camera, buttons, and a screw (no text or labels)

2x Winkel

2x WinkelDbdeckung

2x Führungsschiene

Line drawing of a simple wooden table with a handle and bracket (no text or symbols)

Line drawing of a structural bracket with a small attached component (no text or symbols)

Technical line drawing of a mechanical component with a curved top and base, showing motion arrows (no text or symbols)

Technical line drawing of a structural frame with a bracket and mounting base (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

VORSICHT

Isometric diagram of a rectangular device with internal components and directional arrows indicating flow or movement (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Simple line drawing of a crane frame with a hanging hook and rotational arrow (no text or symbols)

Diagram showing a curved pipe or duct being inserted into a vertical structure, with an inset magnified view highlighting the detail (no text or symbols present)

Illustration of a hand placing a rectangular object on a shelf with an arrow symbol (no text or labels)

WARNUNG

STROMSCHLAGGEFAHR!

Technical line drawing of a mechanical component with an inset close-up showing a magnified view of a component (no text or symbols)

4.1 Abtauen

Simple line drawing of a rectangular device with a circular button on the top (no text or symbols)

(Abbildung ähnlich)

HINWEIS

In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.

For the safety of life and property keep the precautions of these user's instructions as the manufacturer is not responsible for damages caused by omission.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children aged from 3 to 8 years are allowed to load and unload this appliance.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised.
• Keep all packaging well away from children. There is risk of suffocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection cable (as close to the appliance as you can) and remove the door to prevent playing children to suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lack unusable before you discard the old appliance. This will prevent it from becoming a death trap for a child.

General safety

⚠ WARNING! Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

⚠ WARNING! Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

⚠ WARNING! Do not damage the refrigerant circuit.

Safety information

⚠ WARNING! Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacture.
⚠ WARNING! Do not touch the light bulb if it has been on for a long period of time because it could be very hot. ^1)
⚠ WARNING! When positioning the appliance, ensure the supply cord is not trapped or damaged.
⚠ WARNING! Do not locate multiple portable socket-outlets or portable power suppliers at the rear of the appliance.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• The refrigerant isobutane (R-600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.

• During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.

• avoid open flames and sources of ignition

• thoroughly ventilate the room in which the appliance is situated

• It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short circuit, fire and/or electric shock.

• This appliance is intended to be used in household and similar applications such as

• staff kitchen areas in shops, offices and other working environments;

• farm houses and by clients in hotels, motels and other residential type environments;
• bed and breakfast type environments;
• catering and similar non-retail applications.

⚠ WARNING! Any electrical components(plug, power cord, compressor and etc.) must be replaced by a certified service agent or qualified service personnel.

⚠ WARNING! The light bulb supplied with this appliance is a “special use lamp bulb” usable only with the appliance supplied. This “special use lamp” is not usable for domestic lighting. ^1)

Safety information

• Power cord must not be lengthened.
- Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire.
- Make sure that you can come to the mains plug of the appliance.
- Do not pull the mains cable.
- If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire.
- You must not operate the appliance without the lamp.
•This appliance is heavy. Care should be taken when moving it.
- Do not remove nor touch items from the freezer compartment if you hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.
- Avoid prolonged exposure of the appliance to direct sunlight.

Daily use

• Do not put hot on the plastic parts in the appliance.
• Do not place food products directly against the rear wall.
• Frozen food must not be re-frozen once it has been thawed out. ^1)
• Store pre-packed frozen food in accordance with the frozen food manufactures instructions. ^1)
• Appliance's manufactures storage recommendations should be strictly adhered to. Refer to relevant instructions.
• Do not place carbonated of fizzy drinks in the freezer compartment as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. ^1)
• Ice lollies can cause frost burns if consumed straight from the appliance. ^1)

To avoid contamination of food, please respect the following instructions

• Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage systems.
• Clean water tanks if they have not been used for 48h; flush the water system connected to a water supply if water has not been drawn for 5 days.
• Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.

- Two-star frozen-food compartments(if they are presented in the appliance) are suitable for storing pre-frozen food, storing or making ice-cream and making ice cubes.

Safety information

• One-, two- and three -star compartments (if they are presented in the appliance) are not suitable for the freezing of fresh food.
• If the appliance is left empty for long periods, switch off, defrost, clean, dry and leave the door open to prevent mount developing within the appliance.

Careandcleaning

• Before maintenance, switch off the appliance and disconnect the mains plug from the mains socket.
• Do not clean the appliance with metal objects.
• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper. ^1)
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain is blocked, water will collect in te bottom of the appliance. ^2)

Installation

Important! For electrical connection carefully follow the instructions given in specific paragraphs.

• Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it. In that case retain packing.
• It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
• Wherever possible the spacers of the product should be against a wall to avoid touching or catching warm parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.

Service

• Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person.
• This product must be serviced by an authorized Service Center, and only genuine spare parts must be used.

Energy saving

• Don't put hot food in the appliance;
• Don't pack food close together as this prevents air circulating;
• Make sure food don't touch the back of the compartment(s);

1) If there is a freezer compartment. 2) If there is a fresh-food storage compartment.

Safety information

• If electricity goes off, don't open the door(s);
• Don't open the door(s) frequently;
• Don't keep the door(s) open for too long time;
• Don't set the thermostat on exceeding cold temperatures;
• Some accessories, such as drawers, can be removed to get larger storage volume and lower energy consumption.

Environment Protection

This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the appliance regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the

recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

Packaging materials

The materials with the symbol are recyclable. Dispose the packaging in a suitable collection containers to recycle it.

Disposal of the appliance

1. Disconnect the mains plug from the mains socket.
2. Cut off the mains cable and discard it.

⚠ WARNING! During use, service and disposal of the appliance, please pay attention to the symbol as shown on the left, which is located on the rear of the appliance (rear panel or compressor). It's a risk of fire warning symbol. There are flammable materials in the refrigerant pipes and compressor. Please be far away from a fire source during use, service and disposal of the appliance.

Note: Above picture is for reference only. Real appliance probably is different.

Reverse Door

Tool required: Philips screwdriver, Flat bladed screwdriver.

• Ensure the unit is unplugged and empty.
• To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process.
• All parts removed must be saved to do the reinstallation of the door.
• Do not lay the unit flat as this may damage the coolant system.

• It's better that 2 people handle the unit during assembly.

• Unscrew the top hinge. Then lift the door and place it on a padded surface to avoid scratching.

Simple line drawing of a wooden table with a hanging hook and handle (no text or symbols)

1. Unscrew bottom hinge.

Pure technical line drawing of a structural bracket with no text or symbols

1. Unscrew and move screw holes at top and bottom of cabinet from left to right.

Simple line drawing of a table with two oval objects and an arrow indicating rotation (no text or symbols)

Technical line drawing of a mechanical bracket with mounting feet and a curved component (no text or symbols)

Reverse Door

1. Turn over the top hinge and install it at bottom of left side.

Technical line drawing of a structural bracket or frame (no text or symbols)

1. Place the door back on. Ensure the door is aligned horizontally and vertically so that the seal are closed on all sides before finally tightening the hinge. Then turn over removed bottom hinge and inert it and screw it to the top front of the unit.

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

After changing the hinges to the other side please check whether the door seal closes against the cabinet of the appliance. If this is not the case remove the door seal, turn 180 degrees and refit by pressing the seal in to place.

Installation

Kits for installation

Guide x 2

Guide Cover x 2

Slider x 2

Slider Cover x 2

Screw x 15

Rubber Seal x 1

Install the appliance

1. Ensure the size of cabinet and ventilation are enough.

Installation

1. Slowly and carefully push the appliance into the cabinet. Ensure the opening side is as close to the cabinet wall as possible.
2. If screws in front of door are present, remove them first. Screw a guide to holes in the side of appliance door. Insert the slider into the guide, then fully open and close appliance door and wooden door to check whether wooden door can close totally and smoothly.
3. Open appliance door and wooden door together and mark the position of slider when the slider can function well at all angle during door closes or opens. Take slider out of guide and fix slider with wooden door by three screws. Then fix slider cover onto the slider.
4. Unscrew the guide from appliance door.
5. Repeat step 2 to 5 to fix another slider and cover.
6. Fit two guides with sliders and fix them with screws. Then fix guide covers with guides.

Diagram of a door with two arrows indicating direction, no text or symbols present

Installation

1. Double check the door can close and open smoothly and appliance is sealed well. If not, slightly adjust the unit. Then fix bottom bracket with wooden cabinet.

2. Fix top bracket with wooden cabinet.

3. Attached rubber seal to the gap between unit and wooden cabinet at door open side.

Technical line drawing of a structural frame with a central component and mounting base (no text or symbols)

Simple line drawing of a mechanical setup with a suspended object and rotational arrow (no text or symbols)

Diagram showing a curved pipe or duct with an inset magnified view of the main structure (no text or symbols)

Positioning

Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

Climate class	Ambient temperature
SN	+10°C to +32°C
N	+16°C to +32°C
ST	+16°C to +38°C
T	+16°C to +43°C

Location

The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc.

Warning! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.

Electrical connection

Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.

The manufacturer declines all responsibility if the above safety precautions are not observed.

This appliance complies with the E.E.C. Directives.

First use

Cleaning the interior

Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand new product, then dry thoroughly.

Important! Do not use detergents or abrasive powders, as these will damage the finish.

Temperature Setting

• Plug on your appliance. The internal temperature is controlled by a thermostat. There are 8 settings . 1 is warmest setting and 7 is coldest setting and 0 is to turn off the appliance.
• The appliance may not operate at the correct temperature if it is in a particularly hot or if you open the door often.

Accessories

Movable shelves

The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

Line drawing of a hand holding a shelf with a ruler, no text or symbols present

Positioning the door balconies

To permit storage of food packages of various sizes, the door balconies can be placed at different heights. To make these adjustments proceed as follows: gradually pull the balcony in the direction of the arrows until it comes free, then reposition as required.

Simple diagram of a container with two upward arrows indicating flow or movement (no text or symbols)

Helpful hints and tips

Hints for fresh food refrigeration

To obtain the best performance:

• Do not store warm food or evaporating liquids in the refrigerator
• Do cover or wrap the food, particularly if it has a strong flavour

Hints for refrigeration

Useful hints:

• Make (all types): wrap in polythene bags and place on the glass shelves above the vegetable drawer.
- For safety, store in this way only one or two days at the most.
• Cooked foods, cold dishes, etc...: these should be covered and may be placed on any shelf.
- Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
- butter and cheese: these should be placed in special airtight containers or wrapped in aluminum foil or polythene bags to exclude as much air as possible.
- Milk bottle: these should have a cap and should be stored in the balconies on the door.
- Bananas, potatoes, onions and garlic, if not packed, must not be kept in the fridge.

Cleaning

For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.

Caution! The appliance may not be connected to the mains during cleaning. Danger of electrical shock! Before cleaning switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker or fuse. Never clean the appliance with a steam cleaner. Moisture could accumulate in electrical components, danger of electrical shock! Hot vapors can lead to the damage of plastic parts. The appliance must be dry before it is placed back into service.

Important! Ethereal oils and organic solvents can attack plastic parts, e.g. lemon juice or the juice form orange peel, butyric acid, cleanser that contain acetic acid.

• Do not allow such substances to come into contact the appliance parts.
• Do not use any abrasive cleaners
• Remove the food from the freezer. Store them in a cool place, well covered.
• Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker of fuse.
• Clean the appliance and the interior accessories with a cloth and lukewarm water. After cleaning wipe with fresh water and rub dry.
  • After everything is dry place appliance back into service.

Replace the lamp

The internal light is a LED type. To replace the lamp, please contact qualified technician.

Simple line drawing of a rectangular object with a circular hole, no text or symbols present.

Troubleshooting

Caution! Before troubleshooting, disconnect the power supply. Only a qualified electrician of competent person must do the troubleshooting that is not in this manual.

Important! There are some sounds during normal use (compressor, refrigerant circulation).

Problem	Possible cause	Solution
Appliance does not work	Temperature regulation knob is set at number “0”.	Set the knob at other number to switch on the appliance.
	Mains plug is not plugged in or is loose	Insert mains plug.
	Fuse has blown or is defective	Check fuse, replace if necessary.
	Socket is defective	Mains malfunctions are to be corrected by an electrician.
The food is too warm.	Temperature is not properly adjusted.	Please look in the initial Temperature Setting section.
	Door was open for an extended period.	Open the door only as long as necessary.
	A large quantity of warm food was placed in the appliance within the last 24 hours.	Turn the temperature regulation to a colder setting temporarily.
	The appliance is near a heat source.	Please look in the installation location section.
Appliance cools too much	Temperature is set too cold.	Turn the temperature regulation knob to a warmer setting temporarily.
Unusual noises	Appliance is not level.	Re-adjust the feet.
	The appliance is touching the wall or other objects.	Move the appliance slightly.
	A component, e.g. a pipe, on the rear of the appliance is touching another part of the appliance or the wall.	If necessary, carefully bend the component out of the way.
Water on the floor	Water drain hole is blocked.	See the Cleaning and Care section.

If the malfunction shows again, contact the Service Center.