GTN38267GCW - Tumble drier GRUNDIG - Free user manual and instructions

Product Type	Tumble dryer (Condenser)
Model	GTN38267GCW
Brand	Grundig
Capacity (max)	8 kg
Height (min/max)	84.6 cm / 86.6 cm
Width	59.5 cm
Depth	59.8 cm
Net weight (plastic front door)	50 kg
Net weight (glass front door)	52 kg
Energy efficiency class	A+++
Annual energy consumption	177 kWh
Standard cotton programme time (full load)	152 min
Standard cotton programme time (partial load)	95 min
Condensation efficiency class	A
Sound power level (standard cotton programme)	66 dB(A)
Voltage / Frequency	230 V ~ 50 Hz
Main programmes	Cottons, Synthetics, Shirts, Jeans, Sportswear, Daily, Night (Silent), Bedding, Wool Protect, Delicates, Freshen Up, Timer
Special functions	Express Dry, Anti-creasing, Child Lock, Time Delay (up to 24 h), Audio Warning
Filter cleaning indicators	Lint filter, filter drawer, water tank warning symbols
Installation	Freestanding; stackable on washing machine with appropriate kit

Frequently Asked Questions - GTN38267GCW GRUNDIG

Why does the drying process take too long?

Possible causes: clogged lint filter pores (wash with warm water), blocked filter drawer (clean foam), blocked ventilation grids, insufficient room ventilation, lime deposits on dampness sensor (clean with vinegar), overloading (do not exceed 8 kg), or laundry not spun sufficiently (use higher spin speed in washing machine).

Laundry comes out wet at the end of drying. What should I do?

Check if the selected programme suits the fabric type. Ensure lint filter is clean and filter drawer is not blocked. Avoid overloading and spin laundry at a higher speed before drying. Remember that hot clothes may feel damper than they actually are.

The dryer does not switch on or the programme does not start.

Verify that the dryer is plugged in, the loading door is fully closed, a programme is selected, and the Start/Pause button is pressed. Also check if the Child Lock is activated (deactivate by pressing the Audio Warning/Child Lock button for 3 seconds).

Why is my dryer making unusual noises?

It is normal to hear metallic noise from the compressor and pumping noise when water is pumped to the tank. Ensure the dryer is level and balanced by adjusting the feet. Also check that no objects (e.g., coins, buttons) are inside the drum.

How do I empty the water tank and why does the water tank warning flash?

The water tank must be drained after each cycle. Pull out the tank, empty it, and replace it. If the water tank warning symbol flashes during a programme, the tank is full; drain it and press Start/Pause to resume. For direct water drain connection, the tank does not need emptying.

How often should I clean the lint filter and filter drawer?

Clean the lint filter after every drying cycle. The filter drawer (sponge) should be cleaned when the Filter Drawer Cleaning warning symbol lights up. Wash the sponge by hand, squeeze out excess water, and reinsert it correctly to avoid damage.

How do I activate or deactivate the Child Lock?

Press and hold the Audio Warning / Child Lock button for 3 seconds to activate or deactivate the Child Lock. When active, all buttons except On/Off/Cancel are disabled. The Child Lock symbol appears on the display.

What can I do to save energy when using the dryer?

Spin laundry at the highest possible speed in the washing machine. Sort laundry by type and thickness and dry similar items together. Do not overload the dryer. Clean the lint filter and filter drawer regularly. Avoid opening the door unnecessarily and ventilate the room.

Can I place the dryer on top of a washing machine?

Yes, provided you use an appropriate fixing device (available from Authorized Service). The total weight of both machines with full load can reach approx. 180 kg. Ensure the floor is solid. The washing machine must be placed below the dryer, not the other way around. Check the installation table for compatible depths.

What should I do if the loading door does not close properly?

Ensure there is no lint buildup on the door gasket or inner surface. Clean with a soft damp cloth. If the door still does not close, check the door lock for obstructions. Close the door firmly until you hear a locking sound. If the problem persists, contact Authorized Service.

USER MANUAL GTN38267GCW GRUNDIG

1. Please read this user manual first! 3

2. Important instructions for safety and environment.... 4

2.1 General safety......4

2.1 1 Electrical safety ....5

2.1 2 Product safety....6

2.2 Mounting over a washing machine 8

2.3 Intended use 9

2.4 Child safety 9

2.5 Compliance with the WEEE regulation and disposing of the waste product..10

2.6 Compliance with RoHS Directive:10

2.7 Package information .....10

2.8 Technical Specifications......11

3. Your Dryer 12

3.1 Package Contents......12

4. Installation 13

4.1 Appropriate installation location 13

4.2 Removing the transportation safety assembly....13

4.3 Under counter installation .....14

4.4 Connecting to the drain....14

4.5 Adjusting the feet....15

4.6 Electrical connection....15

4.7 Transportation of the dryer .....15

4.8 Warnings about sounds......16

4.9 Changing the illumination lamp .16

5. Preparation 17

5.1 Laundry suitable for drying in the dryer....17

5.2 Laundry not suitable for drying in the dryer....17

5.3 Preparing laundry for drying.....17

5.4 Things to be done for energy saving....17

5.5 Correct load capacity....18

6. Operating the Product ...... 19

6.1 Control panel 19

6.2 Display Symbols .....19

6.3 Preparing the machine......20

6.4 Programme selection....20

6.5 Main programmes .....20

6.6 Main programmes....22

6.7 Programme selection and consumption table....23

6.8 Express Dry....24

6.9 Auxiliary functions....24

6.10 Warning symbols....24

6.11 Starting the programme .....26

6.12 Child Lock....26

6.13 Changing the programme after it has started....26

6.14 Cancelling the programme .....27

6.15 End of programme .....27

7. Maintenance and cleaning.....28

7.1 Cleaning Lint Filter / Loading Door Inner Surface 28

7.2 Cleaning the sensor .....29

7.3 Draining the water tank .....29

7.4 Cleaning the filter drawer......30

7.5 Cleaning the evaporator......32

8. Troubleshooting 33

1. Please read this user manual first!

Dear Customer,

Thank you for preferring a Grundig product. We hope that your product which has been manufactured with high quality and technology will give you the best results. We advise you to read through this manual and the other accompanying documentation carefully before using your product and keep it for future reference. If you transfer the product to someone else, give its manual as well. Pay attention to all details and warnings specified in the user manual and follow the instructions given therein.

Use this user manual for the model indicated on the cover page.

Simple line drawing of an open book with no text or symbols visible

Read the instructions.

Explanation of symbols

Throughout this user manual the following symbols are used:

i	Important information or useful hints about usage.
	Warning for hazardous situations with regard to life and property.
	Warning against electric shock.
	Warning against hot surfaces.
	Warning against fire hazard.

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations.

Do not dispose of the packaging wastes with the domestic waste or other wastes, discard them to the dedicated collection points designated by the local authorities.

2. Important instructions for safety and environment

This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.

2.1 General safety

• The dryer can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children should not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone.
• Children of less than 3 years should be kept away unless continuously supervised.
• Adjustable feet should not be removed. The gap between the dryer and the floor should not be reduced with materials such as carpet, wood and tape. This will cause problems with the dryer.
• Always have the installation and repairing procedures carried out by the Authorized Service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
• Never wash the dryer by spraying or pouring water onto it! There is the risk of electric shock!

2.1.1 Electrical safety

Electrical safety instructions should be followed while electrical connection is made during the installation.

The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by utility.

• Connect the dryer to a grounded outlet protected by a fuse at the value specified on the type label. Have the grounding installation performed by a qualified electrician. Our company shall not be liable for any damages that will arise when the dryer is used without grounding in accordance with the local regulations.
• The voltage and allowed fuse protection is stated on the type label plate.
• The voltage specified on the type label must be equal to your mains voltage.
• Unplug the dryer when it is not in use.
• Unplug the dryer from the mains during installation, maintenance, cleaning and repair works.
• Do not touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
• Do not use extension cords, multi-plugs or adaptors to connect the dryer to power supply in order to decrease the risk of fire and electric shock.
• Power cable plug must be easily accessible after installation.

Damaged mains cable should be changed notifying the Authorized Service.

If the dryer is faulty, it must not be operated unless it is repaired by an authorized service agent! There is the risk of electric shock!

2.1.2 Product safety

	Points to be taken into consideration for fire hazard:Below specified laundry or items must not be driedin the dryer considering fire hazard.Unwashed laundry itemsItems soiled with oil, acetone, alcohol, fuel oil, kerosene, stain removers, turpentine, paraffin or paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.For this reason especially the items containing the above specified stains must be washed very well, to do this use adequate detergent and choose a high washing temperature.
	Below specified laundry or items must not be dried in the dryer due to the fire hazard:Garments or pillows bolstered with rubber foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads.Clothing cleaned with industrial chemicals.Items such as lighter, match, coins, metal parts, needle etc.may damage the drum set or may lead to functional problems.Therefore check all the laundry that you will load into your dryer.Never stop your dryer before the programme completes. If you must do this, remove all laundry quickly and lay them out to dissipate the heat.
	Clothes that are washed inadequately may ignite on their own and even may ignite after drying ends.

- You must provide enough ventilation in order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect.

Underwear that contains metal reinforcements should not be dried in the dryer. Dryer may be damaged if metal reinforcements come loose and break off during drying.

	Use softeners and similar products in accordance with the instructions of their manufacturers.
	Always clean the lint filter before or after each loading. Never operate the dryer without the lint filter installed.

• Never attempt to repair the dryer by yourself. Do not perform any repair or replacement procedures on the product even if you know or have the ability to perform the required procedure unless it is clearly suggested in the operating instructions or the published service manual. Otherwise, you will be putting your life and others' lives in danger.
• There must not be a lockable, sliding or hinged door that may block the opening of the loading door in the place where your dryer is to be installed.
• Install your dryer at places suitable for home use. (Bathroom, closed balcony, garage etc.)
• Make sure that pets do not enter the dryer. Check the inside of the dryer before operating it.
• Do not lean on the loading door of your dryer when it is open, otherwise it may fall over.
• The lint must not be allowed to accumulate around the tumble dryer

2.2 Mounting over a washing machine

• A fixing device should be used between the two machines when installing the dryer above a washing machine. The fitting device must be installed by the authorized service agent.
• Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the products on a solid floor that has sufficient load carrying capacity!

Washing machine cannot be placed on the dryer. Pay attention to the above warnings during the installation on your washing machine.

Installation Table for Washing Machine and Dryer
Dryer Depth	Washing Machine Depth
	62 cm	60 cm	54 cm	50 cm	49 cm	45 cm	40 cm
54 cm	Can be installed					Can be installed	Cannot be installed
60 cm	Can be installed					Cannot be installed

2.3 Intended use

• Dryer has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.
• Use the dryer only for drying laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
• The service life of the dryer that you purchased is 10 years. During this period, original spare parts will be available to operate the dryer properly.

2.4 Child safety

• Packaging materials are dangerous for the children. Keep packaging materials away from children.
• Electrical products are dangerous for the children. Keep children away from the product when it is operating. Do not let them tamper with the dryer. Use the child-proof lock in order to prevent the children to tamper with the dryer.

Child-proof lock is on the control panel. (See Child lock)

- Keep loading door closed even when the dryer is not in use.

2.5 Compliance with the WEEE regulation and disposing of the waste product

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.

2.6 Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

2.7 Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

2.8 Technical Specifications

EN
Height (Min. / Max.) 84,6 cm / 86,6 cm*
Width 59,5 cm
Depth 59,8 cm
Capacity (max.) 8 kg **
Net weight (plastic front door usage) 50 kg
Net weight (glass front door usage) 52 kg
Voltage	See type label***Rated
Model code

* Min. height: Height with adjustable feet are closed.
Max. height: Height with adjustable feet are opened maximum.
** Dry laundry weight before washing.
*** Type label is located behind the loading door.

	Technical specifications of the dryer are subject to specification without notice to improve the quality of the product.
	Figures in this manual are schematic and may not match the product exactly.
	Values stated on markers on the dryer or in the other published documentation accompanying with the dryer are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the dryer, these values may vary.

3. Your Dryer

3.1 Package Contents

1. Water drain hose *
2. Filter drawer spare sponge*
3. User Manual
4. Drying basket*
5. Drying basket user manual*

*It can be supplied with your machine depending on its model.

4. Installation

Before the calling the nearest Authorized Service for the installation of the dryer, ensure that electrical installation and water drain is appropriate referring to the user's manual. (See 4.4 Connecting to the drain and 4.6 Electrical connection) If they are not suitable, contact a qualified electrician and technician to make necessary arrangements.

	Preparation of the dryer's location as well as the electrical and waste water installations is under customer's responsibility.
	Prior to installation, visually check if the dryer has any defects on it. If the drier is damaged, do not have it installed. Damaged products cause risks for your safety.
	Let your dryer wait for 12 hours before starting to use it.

4.1 Appropriate installation location

• Install the dryer on a stable and level surface.
- Dryer is heavy. Do not move it by yourself.
- Operate your dryer in a well ventilated, dust-free environment.
- The gap between the dryer and the surface should not be reduced by the materials such as carpet, wood and tape.
- Do not cover the ventilation grills of the dryer.
- There must not be a lockable, sliding or hinged door that may

block the opening of the loading door in the place where your dryer is to be installed.

• Once the dryer is installed, it should stay at the same place where its connections have been made. When installing the dryer, make sure that its rear wall does not touch anywhere (tap, socket, etc.).
• Place the dryer at least 1 cm away from the edges of other furniture.
• Your dryer can be operated at temperatures between +5°C and +35°C. If the operating conditions fall outside of this range, operation of the dryer will be adversely affected and it can get damaged.
• The rear surface of the tumble dryer shall be placed against a wall.

Do not place the dryer on the power cable.

4.2 Removing the transportation safety assembly

Remove the transportation safety assembly before using the dryer for the first time.

Open the loading door.

There is a nylon bag inside the drum that contains a piece of styrofoam. Hold it from its section marked with XX XX.

Pull the nylon towards yourself and remove the transportation safety assembly.

Diagram of a hand opening a large circular device with internal components (no text or symbols)

Check that no part of the transportation safety assembly remains inside the drum.

4.3 Under counter installation

This product can be installed under a counter if the height of the counter is sufficient.

While using undercounter dryer, it should never be operated without undercounter installation part. For the appropriate undercounter installation part contact the Authorized Service.

Dryer Depth 60	cm 54 cm
Stock number of under-bench installation part	2979700200	2973600200

Leave at least 3 cm of space around the sides and the rear wall of the dryer when installing it under a counter.

If installed under a countertop, drying durations can extend.

4.4 Connecting to the drain

In products equipped with condenser unit, water accumulates in the water tank during the drying cycle. You should drain accumulated water after each drying cycle.

You can directly drain accumulated water through the water drain hose supplied with the product instead of periodically draining the water collected in the water tank.

Connecting the water drain hose

1-2 Pull hose at the behind of the dryer by hand in order to disconnect it from where it is connected. Do not use any tools to remove the hose.

3 Connect one end of the drain hose supplied with the dryer to the connection point from where you removed the hose of the product in previous step.

4 Connect the other end of the drain hose directly to the wastewater drain or to the washbasin.

Technical line drawing of a mechanical component with internal channels and mounting brackets (no text or symbols)

Illustration of a hand inserting a cable into a mechanical component (no text or symbols visible)

Hand operating a mechanical device with a tool inserted, no visible text or symbols

Technical diagram of a mechanical assembly with coiled tubing and mounting brackets (no text or symbols)

Hose connection should be made in a safe manner. Your drain house will be flooded if the hose comes out of its housing during water discharge.

Water drain hose should be attached to a height of maximum 80 cm.

Make sure that the water drain hose is not stepped on and it is not folded between the drain and the machine.

4.5 Adjusting the feet

In order to ensure that the dryer operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet.

Turn the feet to left or right until the dryer stands level and firmly.

Illustration of a hand holding a small mechanical component with a curved arrow indicating rotation (no text or symbols)

Never unscrew the adjustable feet from their housings.

4.6 Electrical connection

For specific instructions for electrical connection required during installation (see 2.1.1 Electrical Safety)

4.7 Transportation of the dryer

Unplug the dryer before transporting it. Drain all water that has remained in the dryer. If direct water drain connection is made, then remove the hose connections.

We recommend carrying the dryer in upright position. If it is not possible to carry the machine in the upright position, we recommend carrying it by tilting towards the right side when looked from the front.

4.8 Warnings about sounds

It is normal to hear a metallic noise from the compressor sometimes during operation.

Line drawing of a washing machine with a circular vent and a rectangular base, showing sound waves (no text or symbols)

Water collected during operation is pumped to water tank. It is normal to hear pumping noise during this process.

Technical line drawing of a mechanical device with internal components and a magnified inset showing sound waves (no text or symbols)

4.9 Changing the illumination lamp

In case an illumination lamp is used in your laundry dryer

To change the Bulb/LED used for illumination of your tumble dryer, call your Authorized Service.

The lamp(s) used in this appliance is not suitable for household room illumination. The intended purpose of this lamp is to assist the user to place laundry in the tumble dryer in a comfortable way. "The lamps used in this appliance have to withstand extreme physical conditions such as vibrations and temperatures above 50 °C."

5. Preparation

5.1 Laundry suitable for drying in the dryer

Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are suitable for drying in a dryer and make sure that you select the appropriate programme.

LAUNDRY DRYING SYMBOLS
	Drying Symbols	Suitable for dryer		No Iron		Sensitive / Delicate dry		Do not dry with dryer		Do not dry
	Drying Settings	At any temperature	At high temperature	At medium temperature	At low temperature	Without heating	Hang to dry	Lay to dry	Hang wet to dry	Lay in shadow to dry	Dry-cleanable
IRON	Iron -
	Dry or Steam			Iron at high temperature		Iron at medium temperature		Iron at low temperature	Do not iron		Iron without steam
	Maximum temperature			200°C 150		°C 110		°C

	Iron -
IRON	Dry or Steam	Iron at high temperature	Iron at medium temperature	Iron at low temperature	Do not iron	Iron without steam
	Maximum temperature	200 °C 150	°C 110	°C

5.2 Laundry not suitable for drying in the dryer

Delicate embroidered fabrics, woolen, silk garments, delicate and valuable fabrics, airtight items and tulle curtains are not suitable for machine drying.

5.3 Preparing laundry for drying

• Laundry may be tangled with each other after washing. Separate the laundry items before placing them into the dryer.
• Dry garments having metal accessories such as zippers, inside out.

- Fasten the zippers, hooks and buckles and button sheets.

5.4 Things to be done for energy saving

Following information will help you use the dryer in an ecological and energy-efficient manner.

• Spin your laundry at the highest speed possible when washing them. Thus, the drying time is shortened and energy consumption is reduced.

• Sort out the laundry depending on their type and thickness. Dry the same type of laundry together. For example thin kitchen towels and table clothes dries earlier than thick bathroom towels.

• Follow the instructions in the user manual for programme selection.

• Do not open the loading door of the machine during drying unless necessary. If you must certainly open the loading door, do not to keep it open for a long time.

- Do not add wet laundry while the dryer is in operation

- Clean the lint filter drawer before or after each drying cycle. (See 7.1 Cleaning Lint Filter / Loading Door Inner Surface)

- Clean the filter periodically when there is visible air collection on it or when the symbol lights up, if there is a filter drawer cleaning warning symbol « available.

(See 7.4 Cleaning the filter drawer)

- Ventilate the room, where the dryer is located, well during drying.

5.5 Correct load capacity

Follow the instructions in the "Programme selection and consumption table". Do not load more than the capacity values stated in the table.

Diagram of a washing machine with internal tissue and ventilation system (no text or labels)

It is not recommended to load the dryer with laundry exceeding the level indicated in the figure. Drying performance will degrade when the machine is overloaded. Furthermore, dryer and the laundry can get damaged.

Following weights are given as examples.

Laundry	Approximate weights (g)*
Cotton quit covers (double)	1500
Cotton quit covers (single)	1000
Bed sheets (double)	500
Bed sheets (single)	350
Large tablecloths	700
Small tablecloths	250
Tea napkins	100
Bath towels	700
Hand towels	350
Blouses	150
Cotton shirts	300
Shirts	250
Cotton dresses	500
Dresses	350
Jeans	700
Handkerchiefs (10 pieces)	100
T-Shirts	125

*Dry laundry weight before washing.

6. Operating the Product

6.1 Control panel

1. On/Off/Cancel
2. Programme number display
3. Display
4. Start/Pause
5. Time delay
6. Alarm sound volume / child safety lock
7. Express dry /Selection of timer programmes
8. Programme selection

6.2 Display Symbols

Remaining time indicator*

Filter Drawer Cleaning warning symbol

Filter cleaning warning symbol

Audio warning Symbol

Child Lock warning symbol

Water Tank warning symbol

End Time Symbol

Start / Pause symbol

Programme progress bar

*Time that appears on display indicates the remaining time until the end of the programme and changes according to the dampness level of the laundry and model of the dryer.

6.3 Preparing the machine

1. Plug in the machine.
2. Place the laundry in the machine.
3. Press the On/off/cancel button for 1 second (long).
4. When your machine is operated for the first time, it starts with the default programme (wardrobe dryness for cottons).

Pressing the On/Off/Cancel button does not necessarily mean the programme has started. Press Start/Pause button to start the programme.

6.4 Programme selection

1. Decide the appropriate programme from the table below which includes drying levels.
2. Select the desired programme with the Programme Selection knob.

Extra Dry	Only the cotton laundry is dried at normal temperature. Thick and multi layered laundry (towels, linens, jeans and etc.) are dried in a way that they do not require ironing before being placed in the wardrobe.
Cupboard Dry	Normal laundry (tablecloths, underwear and etc.) are dried in a way that they do not require ironing before being placed in the wardrobe.

Cupboard Dry Plus	Normal laundry (E.g.: tablecloths, underwear) are dried in a way that they do not require ironing before placing in the drawers, but more than those in the ready to wear option.
Iron Dry	Normal laundry (shirts, dresses and etc.) are dried ready to be ironed.

For further programme details, see, "Programme selection and consumption table".

6.5 Main programmes

Depending on the fabric type, the following main programmes are available:

- Cottons

Dry durable laundry with this programme. Dries at normal temperature. It is recommended to use for your cotton items (bed sheets, quilt covers, towels, bathrobes, etc.).

- Synthetics

Dry less durable laundry with this programme. Recommended for synthetics.

6.6 Additional programmes

For special occasions, the following additional programmes are available:

Depending on the different device model, the additional programmes may vary.

- Shirts

This programme dries the shirts more sensitively and creases them less and thus, helps to iron them more easily.

There may be a little moisture on the shirts at the end of the programme. We recommend you not to leave the shirts in the dryer.

- Jeans

Use this programme to dry your jeans that are spun at high speeds in the washing machine.

Put the jeans into the dryer with the inside turned out.

- Sportswear

Use this programme to dry together the synthetic and cotton laundry items and the laundry items made of mixed fabrics.

• Daily

This programme is used to dry cottons and synthetics daily, and lasts for 100 minutes.

- Night (Silent)

In this programme the level of noise emitted to the environment will be the lowest. Volume level will be fifty percent lower with respect to the ‘wardrobe dry for cottons’ programme.

- Bedding

Dry fiber quilts with 'machine-dryable' label only. Make sure you are loading the quilt in the correct way to avoid damages on the machine and the quilt. Take out the quilt cover before loading the quilt in the machine. Fold the quilt in two before loading.

- Do not load more than 1 double-size fiber quilt (200x200 cm). Do not dry items containing cotton such as quilts, pillows and etc.

- Do not dry items other than quilts such as carpets, rugs or mats. Permanent damage may arise in your machine.

To obtain better results from your dryer, your laundry must be washed with suitable programmes and spun at the recommended spin speeds in the washing machine.

- Wool Protect

Use this programme for drying wool fabrics and textiles such as sweaters, which have been washed according to their care label instructions.

We recommend taking the laundry out of the device, once the programme is completed.

APPAREL CARE

The wool programme of this tumble dryer has been approved by The Woolmark Company for drying any machine-launderable wool fabrics, provided that the products have been washed as indicated by their care label instructions and will be dried in accordance with this device manufacturer's instructions (M1621). Woolmark is a registered trademark in the UK, Ireland, Hong Kong and India.

- Delicates

You can dry your highly delicate laundry (silk blouses, fine underwear, etc.) that are suitable for drying or laundry which is advised to be hand-washed at a lower temperature.

It is recommended to use a cloth bag to avoid certain delicate garments and laundry from getting creased or damaged. Take your laundry immediately out of the dryer and hang them after the programme ends in order to prevent them being creased.

- Freshen Up

Only ventilation is performed for 10 minutes without blowing hot air. You can air the clothes that have been kept in closed environments for a long time and deodorize unpleasant odours thanks to this programme.

- Timer Prog.

Using timer programmes (10 minutes, 20 minutes, 30 minutes, 40 minutes, 50 minutes, 60 minutes, 80 minutes, 100 minutes, 120 minutes, 140 minutes, and 160 minutes), may help you to achieve the desired degree of dryness even at low temperatures.

In order to select any drying time, you need to press the timer selection "key.

With this programme, the machine dries for the time selected regardless of the dryness level.

6.7 Programme selection and consumption table

Programmes		Capacity (kg)	Spin speed in washing machine (rpm)	Approximate amount of remaining humidity	Drying time (minutes)	Express Dry
Cottons / Coloreds
	Extra dry 8 1000 % 60	165 130
	Cupboard dry 8 / 4 1000 % 60	152 / 95 115
	Iron dry 8 1000 % 60	124 95
Shirts 1,5 1200 % 50 50 35
Jeans		4 1200 % 50 117 85
Sportswear		4 1000 % 60 105 70
Daily		4 1200 % 50 100 65
Bedding		2,5 1000 % 50 120
Night		8 1000 % 60 240
Delicates		2	600	% 40	50
Wool Protect		1,5	600	% 50	146
Synthetics
	Cupboard dry	4 800	% 40	75 50
	Iron dry	4 800	% 40	59 34
Energy consumption values
Programmes		Capacity (kg)	Spin speed in washing machine (rpm)	Approximate amount of remaining humidity	Energy consumption value kWh	Express Dry (kwh)
Cupboard dry for cottons*		8 / 4	1000	% 60	1,42 / 0,83	2,47
Iron dry for cottons		8	1000	% 60	1,15	1,99
Cupboard dry for synthetics		4	800	% 40	0,51	0,87
Power consumption of the off-mode for the standart cotton programme at full load, PO (W)					0,4
Power consumption of the left-on mode for the standart cotton programme at full load, PL (W)					1,0
Contains fluorinated greenhouse gases covered by the Kyoto Protocol. Hermetically sealed.R134a / 0,52 kg - GWP:1430 - 0,744 tCO2e

„Cotton cupboard dry programme“ used at full and partial load is the standard drying programme to which the information in the label and the fiche relates, that this programme is suitable for drying normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption for cotton.

* : Energy assessment - standard programme (EN 61121:2012) All filters must be cleaned before initiating any test series. Any values in the table have been determined in accordance with the standard EN 61121:2012. Depending on the laundry type, spin-drying speed and voltage fluctuations, the values may vary.

6.8 Express Dry

This application is available for all programmes highlighted with dark colour on the control panel.

For example in case of “wardrobe ready for cotton” the usual programme duration is 2:32, the ExpressDy feature reduces the required time to 1:55.

2:32

1:55

6.9 Auxiliary functions Audio Warning

After completing a programme, the dryer generates an acoustic signal. To adjust the volume, use the acoustic signal key.

The volume may be adjusted either before starting the programme or when the dryer is running the programme.

(1)

2:25

Anti-creasing

A 2-hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme has come to an end. This programme rotates the laundry in 10-minute intervals without heat to prevent creasing.

6.10 Warning symbols

Warning symbols may differ according to the model of your machine.

Lint filter cleaning

When the programme is completed, a warning symbol will appear to remind that the filter needs to be cleaned.

If the Filter Cleaning symbol in continuously, refer to "Troubleshooting" section.

Water tank

When the programme is completed, a warning symbol will appear to remind that the water tank needs to be drained.

If the water tank becomes full while the programme is running, the warning symbol will start to flash and machine will pause. Drain the water in the water tank and press Start / Pause button to resume the programme. The warning symbol turns off and the programme resumes operating.

Cleaning the filter drawer

Warning symbol flashes to remind that the filter drawer needs to be cleaned.

End Time Setting

End Time Setting function allows you to delay the ending time of the programme up to 24 hours.

1. Open the loading door and put the laundry in.
2. Select the drying programme, spin speed and, if required, the auxiliary functions.

3. Press End Time Setting selection button to set the desired End Time Setting symbol lights up on the display.(When the button is pressed and hold, End Time proceeds uninterruptedly).

4. Press Start/Pause button. End Time Setting starts to count down. The “:” in the middle of the displayed End Time Setting will start to flash.

Additional laundry may be loaded / taken out during the End Time period. At the end of the End Time countdown process, End Time symbol disappears, drying process starts and the programme duration is displayed. The time on the display is the total of normal drying time and End Time.

Changing the End Time

If you want to change the time during countdown:

1. Press On/Off/Cancel button for 3 seconds to cancel the programme. Restart the machine and repeat the End Time procedure for the desired time.
2. When your machine is operated for the first time, it starts with the default programme (wardrobe dryness for cottons).

Cancélling End Time function

If you want to cancel the End Time countdown and start the programme immediately:

1. Press On/Off/Cancel button for 3 seconds to cancel the programme.
2. Press On/Off/Cancel button to start the programme you have previously selected.

6.11 Starting the programme

Press Start/Pause button to start the programme.

Start symbol will light up to indicate that the programme has started and “:” symbol in the middle of the remaining time will keep flashing.

6.12 Child Lock

Machine is equipped with a Child Lock which prevents interfering with the current programme flow by pressing any button. All buttons except the On/Off/Cancel button on the control panel are deactivated when the Child Lock is active.

In order to activate the Child Lock, press Audio Warning, Child Lock button for 3 seconds.

To start a new programme after the current programme is over or to interrupt the current programme, the Child Lock should be deactivated. Press the same button for 3 seconds again to deactivate the Child Lock.

Lock symbol will appear on the display when the Child Lock is activated.

Child Lock is deactivated when the machine is switched off and on with On/Off/Cancel button.

When the Child Lock is activated:

Display symbols will not change even if the position of Programme Selection knob is changed while the machine is running or in halt.

If the Child Lock is deactivated after changing the position of the Programme Selection knob while the machine is running, the machine stops and new programme information is displayed.

6.13 Changing the programme after it has started

After the machine starts, you can change the selected programme and dry your laundry in a different programme.

1. If you want to select Extra Dry programme instead of Iron Dry programme, for instance, press the Start / Pause button for 1 second to stop the programme.
2. Select Extra Dry programme by turning the Programme Selection knob.
3. Press the Start/Pause button to start the programme.

Adding / removing laundry in Pause mode

In order to add or take out laundry after the drying programme has started:

1. Press Start/Pause button to switch the machine to Pause mode. Drying process will stop.

2. While in Pause mode, open the loading door, add or take out laundry and close the loading door.

3. Press the Start/Pause button to start the programme.

	Any laundry added after the drying process has started may cause the clothes that are already dried in the machine intermingle with wet clothes and the result will be wet laundry after the drying process is over.
	You may repeat laundry adding or removing process as many times as you desire during drying. However, this process will increase the programme time and energy consumption since the drying process will be interrupted repeatedly. Therefore, it is recommended to add laundry before the drying programme has started.
	If you select a new programme by turning the Programme Selection knob while your machine is in Pause mode, then the current programme is aborted and new programme information is displayed.
	CAUTION: Do not touch the inner surface of the drum when adding or taking out laundry while a programme is running. Surfaces of the drum are hot.

6.14 Cancelling the programme

If you want to stop drying and cancel the programme for any reason after the machine has started to run, press and hold the On/Off/Cancel button for 3 seconds.

CAUTION: As the inside of the machine will be excessively hot when you cancel the programme while the machine is running, activate the ventilation programme to cool it down.

6.15 End of programme

Lint Filter Cleaning and Water Tank warning symbols light up in the programme follow-up indicator when the programme comes to an end. The loading door can be opened and the machine becomes ready for a second cycle.

Press On/Off/Cancel button to switch off the machine.

2-hour Anti-creasing programme will be activated if the laundry is not taken out after the programme has come to an end.

Clean the lint filter after each drying. (See "Lint Filter and Loading Door Inner Surface")

Drain the water tank after each drying cycle. (See "Draining the water tank")

7. Maintenance and cleaning

Service life of product extends and frequently experienced problems will be reduced if it is cleaned at regular intervals.

7.1 Cleaning Lint Filter / Loading Door Inner Surface

Lint and fiber released from the laundry to the air during the drying cycle are collected in the Lint Filter.

	Such fiber and lint are generally formed during wearing and washing.
	Always clean the lint filter and the inner surfaces of the loading door after each drying process.
	You can clean the lint filter housing with a vacuum cleaner.

To clean the lint filter:

• Open the loading door.
• Remove the lint filter by pulling it up and open the lint filter.
• Clean lint, fiber, and cotton raveling by hand or with a soft piece of cloth.
• Close the lint filter and place it back into its housing.

Technical diagram of a mechanical fan or vent assembly with no visible text or symbols

Illustration of hands holding a cylindrical object with red arrows indicating force or movement (no text or symbols)

Line drawing of a hand pressing down on a curved mechanical component (no text or symbols)

Line drawing of a hand washing clothes from a door (no text or symbols)

- A layer can build up on the filter pores that can cause clogging of the filter after using the dryer for a while. Wash the lint filter with warm water to remove the layer that builds up on the lint filter surface. Dry the lint filter completely before reinstalling it.

Line drawing of a hand using a tool to clean or wash a tray with liquid (no text or symbols)

- Clean the entire inner surface of the loading door and loading door gasket with a soft damp cloth.

Line drawing of hands cleaning a circular mechanical component (no text or symbols)

Line drawing of hands installing or adjusting a circular component with tools (no text or symbols)

7.2 Cleaning the sensor

There are dampness sensors in the dryer that detect whether the laundry is dry or not.

To clean the sensors:

• Open the loading door of the dryer.
• Allow the machine to cool down if it is still hot due to the drying process.
• Wipe the metal surfaces of the sensor with a soft cloth, dampened with vinegar and dry them.

	Clean metal surfaces of the sensors 4 times a year.
	Do not use metal tools when cleaning metal surfaces of the sensors.
	Never use solvents, cleaning agents or similar substances for cleaning due to the risk of fire and explosion!

Line drawing of a hand inserting a small component into a circular device component (no text or symbols)

7.3 Draining the water tank

Dampness of the laundry is removed and condensed during drying process and the water that arise accumulates in the water tank. Drain the water tank after each drying cycle.

	Condensed water is not drinkable!
	Never remove the water tank when the program is running!

If you forget to drain the water tank, the machine will stop during the subsequent drying cycles when the water tank is full and the Water Tank warning symbol will flash. If this is the case, drain the water tank and press Start / Pause button to resume the drying cycle.

To drain the water tank:

- Pull the drawer and remove the water tank carefully.

Line drawing of hands installing or adjusting a device component on a machine (no text or symbols visible)

- Drain the water in the tank.

Technical line drawing of a mechanical device with no visible text or symbols

• If there is lint accumulation in the funnel of the water tank, clean it under running water.
• Place the water tank into its seat.

If the direct water draining is used as an option, there is no need to empty the water tank.

7.4 Cleaning the filter drawer

Lint and fiber that could not be captured by the lint filter are blocked in the filter drawer behind the kick plate. Clean the filter drawer once filter drawer cleaning warning symbol is on.

There is an one stage filter. This one stage filter is from sponge

To clean the filter drawer:

- Press the kick plate button to open the kick plate.

Line drawing of a hand holding a tool interacting with a grid-patterned panel inside a container (no text or symbols)

- Remove the filter drawer cover by turning it in the direction of arrow.

Hand inserting a component into a computer drive (no text or symbols visible)

- Pull out the filter drawer.

Illustration of a hand inserting a component into a device panel (no text or symbols visible)

- Open the filter drawer by pressing the red button.

Illustration of a hand pressing down on a device with a scroll wheel (no text or symbols)

• Take out the filter drawer sponge.

Diagram of a mechanical device with internal components and directional arrows indicating movement or force (no text or symbols)

- Wash the filter drawer sponge by hand to remove the fiber and lint on the surface. After washing the sponge, squeeze it by hand and remove the excess water. Replace the sponge.

It is not necessary to clean the sponge if lint and fiber accumulation on it is not significant.

- Place the sponge back into its place.

Diagram showing two mechanical components with arrows indicating direction of movement (no text or symbols)

Please place the sponge carefully inside the frame of the filter cassette shown by arrows in order to avoid squeezing when filter drawer closed".:

Open and closed diagram of a multi-compartment container or storage unit (no text or symbols visible)

- Close the filter drawer as to lock the red button.

Illustration of a hand holding a device with an arrow indicating rotation (no text or symbols)

- Place the filter drawer back into its place, turn the filter drawer cover in the arrow direction and close it securely.

Hand inserting a device into a computer case, showing internal components and wiring (no text or symbols)

- Close the kick plate cover.

Line drawing of a hand holding a device with a red arrow pointing to it, next to a curved line (no text or symbols)

	Drying without the filter drawer sponge in place will damage the machine!
	A dirty lint filter and filter drawer will cause longer drying periods and higher energy consumption.
	The sponge filter must not be replaced dripping wet as this can cause a fault.

7.5 Cleaning the evaporator

Clean the lint accumulated on the fins of the evaporator located behind the filter drawer with a vacuum cleaner.

Diagram of a hand crossed out of a device panel with no visible text or symbols

Diagram showing a car interior with a black tool applying material to a textured surface (no text or symbols)

You can also clean by hand provided that you wear protective gloves. Do not attempt to clean with bare hands. Evaporator fins can harm your hand.

8. Troubleshooting

Drying process takes too much time.

• Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
• Filter drawer may be blocked>>>clean the foam inside the filter drawer.
• Ventilation grids on the front side of the machine are blocked. >>> Remove the objects (if any) that block ventilation in front of the ventilation grids.
• Ventilation is not sufficient since the room where the machine is installed is very small. Open the door and window of the room to avoid the room temperature increase too much.
• Lime deposit has built up on the dampness sensor. >>> Clean the dampness sensor.
• Excessive laundry is loaded. >>> Do not load the dryer in excess.
• Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.

Laundry comes out wet at the end of drying.

After drying, the hot clothes feel damper than their actual dampness level.

• It is likely that the selected programme did not suit the laundry type.>>>Checking the care labels on clothes, select appropriate programme for the laundry type or use timer programmes in addition.
• Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
• Filter drawer may be blocked>>>clean the foam inside the filter drawer.
• Excessive laundry is loaded. >>> Do not load the dryer in excess.
• Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.

Dryer does not switch on or the programme does not start. Dryer does not start when it is set.

• It is not plugged in. >>> Make sure that the machine is plugged in.
• The loading door is ajar. >>> Make sure that the loading door is closed securely.
• Programme is not selected or the Start / Pause / Cancel button is not pressed. >>> Make sure that the programme is selected and the machine is not in Pause mode.
• Childproof Lock is activated. >>> Deactivate the Childproof Lock.

Programme is interrupted without any cause.

Loading door is ajar. >>> Make sure that the loading door is closed securely.There was a power failure. >>> Press Start / Pause / Cancel button to start the programme.Water tank is full. >>> Drain the water tank.

Laundry has shrunk, become felted or deteriorated.

A programme suitable for the laundry type is not used. >>> Check the garment tag and select a programme suitable for the fabric type.

Drum lighting does not turn on. (On models with lamp)

Dryer is not switched on with the On / Off button. >>> Make sure that the dryer is switched on.Lamp is defective. >>> Call Authorized Service Agent to have the lamp replaced.

End/Anti-creasing symbol is on.

Anti-creasing programme is activated in order to prevent laundry that has remained in the machine from creasing. >>> Turn off the dryer and take out the laundry.

End symbol is on.

Programme is over. Turn off the dryer and take out the laundry.

Lint Filter Cleaning symbol is on.

Lint filter is not cleaned. >>> Clean the lint filter.

Lint Filter Cleaning symbol is flashing.

Filter housing is clogged with lints. >>> Clean the lint filter housing.A deposit has built up on the lint filter pores that may cause clogging. >>> Wash the lint filter with warm water.Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.

Water leaks from the loading door

Lint has accumulated on the inner surfaces of the loading door and on the surfaces of the loading door gasket. >>> Clean the inner surfaces of the loading door and the surfaces of the loading door gasket.

Loading door opens spontaneously.

Loading door is ajar. >>> Push the loading door to close until you hear a locking sound.

Water Tank warning symbol is on/flashing.

Water tank is full. >>> Drain the water tank.Water draining hose is bent. >>> If the product is connected directly to a wastewater drain, check the water drain hose.

Filter Drawer Cleaning warning symbol is flashing.

- Filter drawer is not cleaned. >>> Clean the sponge and the filter cloth in the filter drawer.

If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.

PRODUCT FICHE
Complying Commission Delegated Regulation (EU) No 392/2012
Supplier name or trademark		Grundig
Model name		GTN 38267 GC
Rated capacity (kg)		8
Type of Tumble Dryer	Air Vented	-
	Condenser	●
Energy efficiency class (1)		A+++
Annual Energy Consumption (kWh) (2)		177
Type of Control	Automatic	●
	Non-automatic	-
Energy consumption of the standard cotton programme at full load (kWh)		1,42
Energy consumption of the standard cotton programme at partial load (kWh)		0,83
Power consumption of the off-mode for the standart cotton programme at full load, P_o (W)		0,4
Power consumption of the left-on mode for the standart cotton programme at full load, P_L (W)		1,0
The duration of the left on mode (min)		30
Standard cotton programme (3)
Programme time of the standard cotton programme at full load, T_dry (min)		152
Programme time of the standard cotton programme at partial load, T_dry1/2 (min)		95
Weighted programme time of the standard cotton programme at full and partial load ( T_t )		119
Condensation efficiency class (4)		A
Average condensation efficiency of the standard cotton programme at full load, C_dry		91%
Average condensation efficiency of the standard cotton programme at partial load, C_dry1/2		91%
Weighted condensation efficiency of the standard cotton programme at full load and partial load, C_t		91%
Sound power level for the standard cotton programme at full load (5)		66
Built-in		-

• : Yes - : No
(1) Scale from A+++ (most efficient) to D (least efficient)
(2) Energy consumption based on 160 drying cycles of the standard cotton programme at full and partial load, and the consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used.
(3) "Cotton cupboard dry programme" used at full and partial load is the standard drying programme to which the information in the label and the fiche relates, that this programme is suitable for drying normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption for cotton
(4) Scale from G (lest efficient) to A (most efficient)

USCĂTOR

MANUAL DE UTILIZARE

RO

CUPRINS

Simple line drawing of an open book with no text or symbols visible

Line drawing of a hand inserting a component into a circular device (no text or symbols)

Technical diagram of a mechanical or electrical component with no visible text, numbers, or symbols

Hand inserting a cable into a device component (no text or symbols visible)

Hand inserting a component into a device frame (no visible text or symbols)

Technical diagram of a mechanical assembly with coiled tubing and mounting brackets (no text or symbols)

Hand holding a mechanical component with a curved arrow indicating rotation (no text or symbols)

Line drawing of a washing machine with a circular vent and a rectangular base, showing sound waves (no text or symbols)

Technical line drawing of a mechanical device with internal components and a magnified inset showing sound waves (no text or symbols)

Diagram of a washing machine with internal components and lid, showing no text or symbols

6.4 Selectare program

Technical diagram of a circular fan or vent with internal blades and a red arrow indicating a specific component (no text or symbols present)

Illustration of hands holding a cylindrical object with red arrows indicating force or movement (no text or symbols)

Line drawing of a hand pressing down on a curved mechanical component (no text or symbols)

Illustration of hands cleaning a car air conditioner cover (no text or symbols)

Line drawing of a hand using a tool to clean or prepare food items in a tray (no text or symbols)

Line drawing of hands cleaning a circular mechanical component (no text or symbols)

Line drawing of a hand cleaning a circular mechanical component with tools (no text or symbols)

Line drawing of a hand placing a small object into a circular mechanical component (no text or symbols)

Line drawing of hands installing or adjusting a mechanical component with a tray and mounting bracket (no text or symbols)

Line drawing of a mechanical component with a tool inserted, no text or symbols present

Hand cleaning a kitchen sink with a tiled wall and spray bottle (no text or symbols visible)

Line drawing of a hand inserting a component into a computer case (no text or symbols visible)

Illustration of a hand inserting a component into a device panel (no text or symbols visible)

Illustration of a hand pressing down on a device with a curved arrow indicating rotation (no text or symbols)

Diagram of a mechanical component with arrows indicating direction, no text or symbols present

Diagram showing a device being processed into a closed notebook (no text or symbols visible)

Diagram of an open and closed mechanical device with internal compartments (no text or symbols)

Illustration of a hand holding a device with an arrow indicating rotation (no text or symbols present)

Hand inserting a device into a computer case (no text or symbols visible)

Illustration of a hand pressing down on a device panel with a red arrow indicating the handle (no text or symbols present)