GO4 1262D/1-16S - Washing machine CANDY - Free user manual and instructions

USER MANUAL GO4 1262D/1-16S CANDY

Illustration of a white washing machine with control panel and side buttons (no text or symbols)

CZEN

ÚVOD

Vážený zákazníku,

Exterior view of a white washing machine (no visible text or symbols)

CODE 15.170x FRAVING 15.170x Mod N. 3100078XXX XXXX G Type R400000 1982/2016

SL

ČESTITAMO!

With the purchase of this Candy household appliance, you have shown that you will not accept compromises: you want only the best.

Candy is happy to present their new washing machine, the result of years of research and market experience through direct contact with Consumers. You have chosen the quality, durability and high performance that this washing machine offers.

Candy is also able to offer a vast range of other household appliances: washing machines, dishwashers, washer-dryers, cookers, microwave ovens. Traditional ovens and hobs, refrigerators and freezers.

Ask your local retailer for the complete catalogue of Candy products.

Please read this booklet carefully as it provides important guide lines for safe installation, use and maintenance and some useful advise for best results when using your washing machine.

Keep this booklet in a safe place for further consultation.

When contacting Candy or a Customer Services Centre always refer to the Model, No., and G number (if applicable of the appliance see panel).

SK

ÚVOD

The appliance is supplied with a guarantee certificate which allows free use of the Technical Assistance Service.

SK

KAPITÓLA 2

ZÁRUKA

● Turn off the water inlet tap.

- All Candy appliances are earthed. Ensure that the main electricity circuit is earthed. Contact a qualified electrician if this is not the case.

CE Appliance complies with European Directives 73/23/EEC and 89/336/EEC, replaced by 2006/95/EC and 2004/108/EC, and subsequent amendments.

- Do not touch the appliance with wet or damp hands or feet.

- Do not use the appliance when bare-footed.

● Extreme care should be taken if extension leads are used in bathrooms or shower rooms. Avoid this where possible.

WARNING: DURING THE WASHING CYCLE, THE WATER CAN REACH A TEMPERATURE OF 90°C.

● Before opening the washing machine door, ensure that there is no water in the drum.

SK

KAPITOLA 3

POKYNYNA BEZPEČNÉ POUŽÍVANIE PRAČKY

POZOR! NIŽŠIE UVEDENĚ POKYNY PLATIA PRE AKÝKOLVEK DRUH ČISTENIA A ÚDRŽBY

● Vytiahnite vidlicu el. kábla zo zásuvky el. siete

● Uzavrite kohútik privodu vody

Two hand-drawn diagrams showing electrical components with cross marks, no text or symbols present

Illustration of a washing machine with a black-and-white cart handle (no text or symbols)

Illustration of three household appliances: a washing machine, a person using a phone to interact with it, and a washing machine (no text or symbols present)

SI

- Do not use adaptors or multiple plugs.

● This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

- Do not pull the mains lead or the appliance itself to remove the plug from the socket.

● Do not leave the appliance exposed to atmospheric agents (rain, sun etc.)

● In the case of removal, never lift the appliance by the knobs or defensive drawer.

● During transportation do not lean the door against the trolley.

Important!

When the appliance location is on carpet floors, attention must be paid so as to ensure that there is no obstruction to the bottom vents.

● Lift the appliance in pairs as illustrated in the diagram.

- In the case of failure and/or incorrect operation, turn the washing machine off, close the water inlet tap and do not tamper with the appliance. Contact a Candy Technical Assistance Centre for any repairs and ask for original Candy spare parts. Avoidance of these norms may compromise the safety of the appliance.

● Should the supply cord (mains cable) be demaged, this is to be replaced by a specific cable available from the after sales service centre.

SK

Diagram showing a hand using a water pump to clean water, with a dashed outline indicating the process.

max 100 cm +2,6 mt max min 4 cm min 50 cm max 85 cm

SL

Fix the sheet of corrugated material on the bottom as shown in picture.

Connect the fill hose to the tap.

The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused.

IMPORTANT: DO NOT TURN THE TAP ON AT THIS TIME.

Position the washing machine next to the wall. Hook the outlet tube to the edge of the bath tub, paying attention that there are no bends or contractions along the tube

It is better to connect the discharge hose to a fixed outlet of a diameter greater than that of the outlet tube and at a height of min. 50 cm. It is necessary to use the plastic sleeve supplied.

SK

©7 KAPITOLA 6 ©1 KEΦΑΛΑΙΟ 6 DN O F E P G H I C L M B A

OVLÁDACÍ PRVKY

Press the "Start/Pause" button to start the selected cycle.

The programme carries out with the programme selector stationary on the selected programme till cycle ends.

Switch off the washing machine by turning the selector to OFF.

NOTE:

THE PROGRAMME SELECTOR MUST BE RETURN TO THE OFF POSITION AT THE END OF EACH CYCLE OR WHEN STARTING A SUBSEQUENT WASH CYCLE PRIOR TO THE NEXT PROGRAMME BEING SELECTED AND STARTED.

SK

VOLIČ PROGRAMOV S OFF

OTOČENÍM OVLÁDAČA PROGRAMOV SA DISPLEJ ROZSVIETI A ZOBRAZIA SA NA NÓM PARAMETRE ZVOLENÉHO PROGRAMU. SUCÁSNE CISTIACE PROSTRIEDKY SU UČINNÉ UŽ AJ PRI NÍZKYCH TEPLOTÁCH. Z TOHTO DÓVODU, AKO AJ Z DÓVODU ÍNTENZIVNYCH PROGRAMOV, PRÁČKA DOPORUČUJE PRANIE PRI NAJNIŽSÍCH TEPLOTÁCH. V KAZDOM PRÍPADE JE VŠAK MOŽNÉ TEPLOTU PRANIA ZVÝŠIT A TO STLAČENÍM TLAČIDLA REGULUJÚCEHO TEPLOTU. PRE MAXIMÁLNU MOŽNÚ TEPLOTU PRI KAZDOM PROGRAME VYCHÁDZAJTE Z TABULKY PROGRAMOV. UPOZORNENIE: PRÁČKU VYPNETE OTOČENÍM OVLÁDAČA PROGRAMOV DO POLOHY "OFF".

Stlačte tlačidlo „Štart/Pauza" a spustite cyklus prania.

By pressing this button you can activate a special new wash cycle in the Colourfast and Mixed Fabrics programs, thanks to the new Sensor System. This option treats with care the fibres of garments and the delicate skin of those who wear them. The load is washed in a much larger quantity of water and this, together with the new combined action of the drum rotation cycles, where water is filled and emptied, will give you garments which have been cleaned and rinsed to perfection. The amount of water in the wash is increased so that the detergent dissolves perfectly, ensuring an efficient cleaning action. The amount of water is also increased during the rinse procedure so as to remove all traces of detergent from the fibres. This function has been specifically designed for people with delicate and sensitive skin, for whom even a very small amount of detergent can cause irritation or allergy. You are advised to also use this function for children's clothing and for delicate fabrics in general, or when washing garments made of towelling, where the fibres tend to absorb a greater quantity of detergent. To ensure the best performance for your wash, this function is always activated on the Delicates and Wooliens/Handwash programs.

SK

TLAČIDLO "AQUAPLUS"

Sliskhere liacilko jeahou

abyste jej aktivovall (ha displeji re obieví b00)

This button allows you to pre-

programme the wash cycle

to delay the start of the cycle

for up to 24 hours.

to delay the start use the following procedure:

following procedure. Set the required programme.

Press the button once to

Press the battery once to activate it (b00 appears on

the display) and then press it

again to set a 1 hour delay

(h01 appears on the display)

the pre-set delay increases

by 1 hour each time t

button is pressed, until h24

appears on the display, at

which point pressing the

button again will reset the delay start to zero.

Confirm by pressing the

"START/PAUSE" button (the

light on the display starts to

flash). The countdown will

begin and when it has

finished the programme will start automatically.

stan automatically

It is possible to cancel the

delay start by taking the

following action:

Press and hold the button for

5 seconds until the display will

show the settings for the

programme selected. At this stage, it is possible to

At this stage it is possible to start the programme.

start the programme

previously selected by pressing the "START/PAUSE"

pressing the START/FAUSE button or to cancel the

process by setting the

selector to the OFF position

and then selecting another

programme.

SK

TLAČIDLO "POSUNUTÝ

START

The Crease Guard function (Not available on COTTON programmes) minimizes creases as much as possible with a uniquely designed anti-crease system that is tailored to specific fabrics.

MIXED FABRICS - the water is gradually cooled throughout the final two rinses with no spinning and then a delicate spin assures the maximum relaxation of the fabrics.

DELICATE FABRICS - final two rinses with no spinning and then the fabrics are left in water until it is time to unload. When you are ready to unload, press the "Crease Guard" button - this will drain.

WOLLENS/HAND WASH - after the final rinse the fabrics are left in water until it is time to unload and the button indicator blinking.

When you are ready to unload, press the "Crease Guard" button, this will drain and spin ready for emptying.

If you do not want to spin the clothes and activate drain only:

- Turn the programme selector to the "OFF" position;

- Select programme drain only ☐;

- Switch on the appliance again by pressing the "Start/Pause" button.

SK

TLAČIDLO NA "ZABRÁNENIE POKRČENIA"

Press to start the selected cycle.

NOTE: FEW SECONDS AFTER THE START THE WASH CYCLE WILL BEGIN. DURING THE FIRST 4 MINUTES OF THE WASH CYCLE, THE KG DETECTOR (ACTIVE ONLY ON COTTON AND SYNTHETICS PROGRAMMES) WILL WEIGH THE CLOTHES AND UPDATE THE MAXIMUM WASH TIME REMAINING ON THE DISPLAY EVERY FIVE SECONDS UNTIL THE WEIGHT HAS BEEN DETERMINED. WHILE THIS FUNCTION IS OPERATING THE "Kg DETECTOR" INDICATOR IS ON.

CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS STARTED (PAUSE)

Press and hold the "START/PAUSE" button for about 2 seconds, the flashing lights on the options buttons and time remaining indicator will show that the machine has been paused, adjust as required and press the "START/PAUSE" button again to cancel the flashing lights.

If you wish to add or remove items during washing, wait 2 minutes until the safety device unlocks the door. When you have carried out the manoeuvre, close the door, press START button and the appliance will continue working where it left off.

CANCELLING THE PROGRAMME To cancel the programme, set the selector to the OFF position. Select a different programme. Re-set the programme selector to the OFF position.

SK

TLAČIDLÓ ŠTART

3) SPIN SPEED Once the programme has been selected, the maximum spin speed allowed for that programme appears on the display. Pressing the spin button will reduce the speed by 100 rpm each time the button is pressed. The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the spin button repeatedly.

4) DELAY START LIGHT This flashes when delay start has been set.

5) WASH CYCLE TIME When a programme is selected the display automatically shows the maximum cycle duration for a full load, which can vary, depending on the options selected. Once the programme has started you will be kept informed constantly of the time remaining to the end of the wash.

6)Kg DETECTOR Indicator Available on Cotton and Synthetic cycles, during the first 4 minutes of the cycle the intelligent sensor will weigh the laundry and adjust the cycle time, water and electricity consumption accordingly.

7) DEGREE OF SOILING When a programme is selected the relevant indicator will light up to show the minimum possible degree of soiling. Selecting a greater degree of soiling using the special button will cause the corresponding indicator to light up.

SK

Diagram showing a tool interacting with a container labeled '1' and '2', likely illustrating a mechanical or electrical assembly.

Diagram showing a device with labeled parts, including a flower and two tools or components.

Diagram showing a mechanical or electrical component with labeled parts 1 and 2, likely illustrating a process or assembly.

PROGRAM FOR:	PROGRAMME SELECTOR ON:	WEIGHT MAX kg*			RECOMMENDED TEMP. °C	MAX TEMP. °C	CHARGE DETERGENT
							2	8	1
Resistant fabrics Cotton, linen	1)	6	8	9	60°	Up to: 90°	●	●	(●)
Cotton, mixed resistant, Coloureds	1) **	6	8	9	40°	Up to: 60°	●	●	(●)
Mixed fabrics and synthetics Cotton, mixed fabrics, synthetics	1)	3	4	4,5	40°	Up to: 60°	●	●	(●)
Very delicate fabrics		2	2,5	2,5	40°	Up to: 40°	●	●
Rlnse	[0302]	-	-	-	-	-		●
Fast spin		-	-	-	-	-
Drain only	[ABCK]	-	-	-	-	-
Resistant fabrics Mixed fabrics and synthetics Rapid 14 minute	2) Rapid 14'-3'44'	1	1,5	1,5	30°	Up to: 30°	●	●
Resistant fabrics Mixed fabrics and synthetics Rapid 30 minute		2	2,5	2,5	30°	Up to: 40°	●	●
Resistant fabrics Mixed fabrics and synthetics Rapid 44 minute		3	3,5	3,5	30°	Up to: 40°	●	●
Hand wash		1	1,5	1,5	30°	Up to: 30°	●	●
"MACHINE WASHABLE" woollens	[2KZW]	1	2	2	40°	Up to: 40°	●	●
Mix & Wash system programme	MIX & WASH	6	8	9	40°	Up to: 40°	●	●

Diagram showing a mechanical device with labeled parts 1 and 2, likely illustrating a process or assembly.

Please read these notes

* Maximum load capacity of dry clothes, according to the model used (see rating plate).

When washing heavily soiled laundry it is recommended the load is reduced to 3/4 kg maximum.

**Programme also recommended for low-temperature washes (lower than the max. shown). Programme tested in accordance with CENELEC EN 60456 with the maximum Degree of Soiling selected and a temperature of 60°C.

The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or for very delicate fabrics cancel the spin completely this option is available with a spin speed button.

(●) Only with the Prewash button selected. (Programmes with Prewash button available)

- Pressing the wash temperature button makes it possible to wash at any temperature below the maximum allowed.

1) For the programmes shown you can adjust the duration and intensity of the wash using the degree of soiling button.

2) Using the Degree of soiling button on the Rapid cycle will enable you to select either a 14, 30 or 44 minute wash cycle.

OFF MIX & WASH Rigid 14' - 30' - 44'

KAPITOLA 77

TABULKA PRACÍCH PROGRAMOV

PROGRAM PRE	VOLBA UKAZOVATELA VOLICA PROGRAMOV NA:		MAX. NAPLN kg *			ODPORUČANÁ TEPLOTA °C	MAXIMÁLNA TEPLOTA °C	NÁSYPKA PRACÍCH PROSTRIEDKOV
								2	☀	1
Odolné tkaniny Bavlna, fan	1)		6	8	9	60°	Do: 90°	●	●	(●)
Bavlna zmesové odolné	1)	**	6	8	9	40°	Do: 60°	●	●	(●)
Zmesové a syntetické tkaniny Bavlna, zmesové a syntetické tkaniny	1)		3	4	4,5	40°	Do: 60°	●	●	(●)
Veřmi jemné tkaniny			2	2,5	2,5	40°	Do: 40°	●	●
Plákanie			-	-	-	-	-		●
Intenzívne odstredenle			-	-	-	-	-
Jednoduché vypůšťanie vody			-	-	-	-
Odolné tkaniny Zmesové a syntetické tkaniny Rýchloprogram 14'	2) Rapid 14'- [CDWWI]14'		1	1,5	1,5	30°	Do: 30°	●	●
Odolné tkaniny Zmesové a syntetické tkaniny Rýchloprogram 30'			2	2,5	3,5	30°	Do: 40°	●	●
Odolné tkaniny Zmesové a syntetické tkaniny Rýchloprogram 44'			3	3,5	3,5	30°	Do: 40°	●	●
Ručné Pranie			1	1,5	1,5	30°	Do: 30°	●	●
Vlna určená na pranie v práčke			1	2	2	40°	Do: 40°	●	●
„MIX & WASH SYSTEM“ program	MIX & WASH		6	8	9	40°	Do: 40°	●	●

Diagram showing a mechanical or electrical component with labeled parts 1 and 2, including a flower symbol.

PROSİM, PREČÍTAJTE SI TIETO POZNÁMKY:

PROGRAM ZA VOLNO "WOOLMARK"

To je program, ki ga je potrdil WOOLMARK, in ki omogoča temeljito pranje perila, ne da bi ga poškodoval. Tekom programa se izmenjujejo fože aktivnosti in premorov pri temperaturi do 40°C, zaključi pa se s 3 izpiranji in kratkotrajnim ožemanjem.

PROGRAM »MIX & WASH«

The special cycle, certified by WOOLMARK, enables to thoroughly wash garments without damaging them. The cycle comprises of alternate periods of activity and pauses with a maximum temperature of 40°C and concludes with 3 rinses and a short spin.

"MIX & WASH SYSTEM" PROGRAMME

This is an exclusive Candy system and involves 2 great advantages for the consumer:

• to be able to wash together different type of fabrics (e.g. cotton + synthetic etc...) FAST COLOUREDS;

• to wash with a considerable energy saving.

The "Mix & Wash" programme has a temperature of 40^ and alternate dynamic phases (the basket that turns) to static phases (fabrics in soak in phase of rest) with a duration programme that almost reaching the 2 hours. The energy consumption for the complete cycle is only 850 W/h.

Important:

• the first washing of new coloureds fabrics must be done separately:

• In every case, never mix NON-FAST COLOUREDS fabrics.

SK

PROGRAM PRE VLNU

Diagram showing two labeled parts (1 and 2) of a mechanical device with tool-like components and a flower symbol, likely illustrating a process or assembly.

ΠΡΟΣΟΧΗ :

The detergent draw is split

to 3 compartments:

the compartment labelled

"1" is for prewash

detergent;

the compartment

Inghalled "◇" is for an equivalent

additives, fabric softeners

fragrances starch

brighteners etc:

the compartment labelled

"2" is for main wash.

detergent.

SK

KAPITÓLA 9

ZÁSOBNÍK PRACÍCH PROSTRIEDKOV

When washing heavy rugs, bed spreads and other heavy articles, it is advisable not to spin.

To be machine-washed, woollen garments and other articles in wool must bear the "Machine Washable Label".

IMPORTANT:

When sorting articles ensure that:

there are no metal objects in the washing (e.g. brooches, safety pins, pins, coins etc.). cushion covers are buttoned, zips and hooks are closed, loose bells and long tapes of dressing gowns are knotted.

runners from curtains are removed. attention is paid to garment labels, when sorting, any tough stains should be removed prior to washing using stain removers only recommended on label.

SK

KAPITÓLA 10

BIELIZEŇ

DÖLEŽITÉ:

A guide environmentally friendly and economic use of your appliance.

MAXIMISE THE LOAD SIZE

Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. Save up to 50% energy by washing a full load instead of 2 half loads.

DO YOU NEED TO PRE-WASH?

For heavily soiled laundry only! SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry.

IS A HOT WASH REQUIRED?

Pretreat stains with stain remover or sock dried in stains in water before washing to reduce the necessity of a hot wash programme. Save up to 50% energy by using a 60°C wash programme.

SK

KAPITOLA 11

UŽITO NÉ RADY PRE UŽÍVATELA

Mechanical component diagram showing a bolt and nut assembly with a black arrow indicating rotation (no text or symbols)

SL

● Ensure that the water inlet tap is turned on.

● And that the discharge tube is in place.

PROGRAMME SELECTION

Refer to the programme guide to select the most suitable programme.

Turning the selector knob required programme is activate.

The display will show the settings for the programme selected.

Adjust the wash temperature if necessary.

Press the option buttons (if required)

Then press the START button. When the START button is pressed the machine sets the working sequence in motion.

The programme carries out with the programme selector stationary on the selected programme till cycle ends.

Warning: If there is any break in the power supply while the machine is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off.

- When the programme has ended the word "End" will appear on the display

● Wait for the door lock to be released (about 2 minutes after the programme has finished).

- Switch off the machine by turning the programme selector to the "OFF" position.

● Open the door and remove the laundry.

FOR ALL TYPES OF WASH CONSULT THE PROGRAMME TABLE AND FOLLOW THE OPERATIONS IN THE ORDER INDICATED.

SK

- Skontrolujte, či máte pustenú vodu a či je odtoková hadica na mieste.

VOLBAPROGRAMU

Diagram showing hand operating a valve mechanism with directional arrows indicating motion (no text or symbols)

Illustration of a hand using a tool to adjust or install a wall socket, with a magnified inset showing the cable (no text or symbols present)

SI.

ČIŠČENJE FILTRA

The washing-machine is equipped with a special filter to retain large foreign matter which could clog up the drain, such as coins, buttons, etc. These can, therefore, easily be recovered. The procedures for cleaning the filter are as follows:

- Open the flap

- Only available on certain models: Pull out the corrugated hose remove the stopper and drain the water into a container.

● Before removing the filter, place an absorbent towel below the filter cap to collect the small amount of water likely to be inside the pump

● Turn the filter anticlockwise till it stops in vertical position.

- Remove and clean.

● After cleaning, replace by turning the notch on the end of the filter clockwise. Then follow all procedures described above in reverse order.

REMOVALS OR LONG PERIODS WHEN THE MACHINE IS LEFT STANDING

For eventual removals or when the machine is left standing for long periods in unheated rooms, the drain hose should be emptied of all remaining water.

The appliance must be switched off and unplugged. A bowl is needed. Detach the drainage hose from the clamp and lower it over the bowl until all the water is removed.

Repeat the same operation with the water inlet hose.

SK

ČISTENIE FILTRA

FAULT	CAUSE	REMEDY
1. Does not function on any programme	Mains plug not plugged in	Insert plug
	Mains switch not on	Turn on mains switch
	No power	Check
	Electric circuit fuses failure	Check
	Load door open	Close load door
2. Does not load water	See cause 1	Check
	Inlet tap turned off	Turn on water inlet tap
	Timer not set correctly	Set timer on correct position
3. Does not discharge water	Discharge tube bent	Straighten discharge tube
	Odd material blocking filter	Check filter
4. Water on floor around washing machine	Leak from the washer between the tap and inlet tube	Replace washer and tighten the tube on the tap
5. Does not spin	The washing machine has not discharged water	Wait a few minutes until the machine discharges water
	“No spin” setting (some models only)	Turn the programme dial onto spin setting
6. Strong vibrations during spin	Washing machine not perfectly level	Adjust special feet
	Transport bracket not removed	Remove transport bracket
	Washing load not evenly distributed	Distribute the washing evenly
7. Display reads error 0, 1, 5, 7, 8, 9	-	Call service.
8. Display reads error 2	No water fill.	Check water supplies are on.
9. Display reads error 3	No pump out.	Check drain is clear.Check drain hose is not kinked.
10. Display roads error 4	Machine overfilled with water.	Turn off water supply to machine.Call service.

If the fault should persist, contact a Candy Technical Assistance Centre. For prompt servicing, give the model of the washing machine, to be found on the label placed on the cabinet inside of the porthole or on the guarantee certificate.
Important
1 The use of environment friendly detersives without phosphates may produce the following effects: - The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing. - The non-ionic surface-active agents present in the composition of washing machine defersives are often difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine falls to function, carry out the above-mentioned checks before calling the Candy Technical Assistance Service.

SK

KAPITOLA 1133

The manufacturer declines all responsibility in the event of any printing mistakes in this booklet. The manufacturer also reserves the right to make appropriate modifications to its products without changing the essential characteristics.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

09.05 - 41031228 - www.grahffcaestampaul - Printed in Raily - Imprise en Raille