AT-VM95ML - DJ Mixer Audio-Technica - Free user manual and instructions

Product Type	Moving Magnet Phono Cartridge
Model	AT-VM95ML
Frequency Response	20 – 22,000 Hz
Output Voltage	4.0 mV (1 kHz, 5 cm/sec)
Channel Separation	≥ 25 dB (1 kHz)
Channel Balance	≤ 1.5 dB (1 kHz)
Impedance	47 kΩ
Load Capacitance	100 – 200 pF
Stylus Type	MicroLine
Stylus Shape	Nude mounted, microlinear
Tracking Force Range	1.8 – 2.2 g
Recommended Tracking Force	2.0 g
Cartridge Weight	6.1 g
Dimensions (W x H x D)	17.6 x 21.2 x 30.0 mm
Compatible Headshell	Standard 1/2-inch mount
Power Supply	No internal power; passive
Included Accessories	Mounting screws, stylus guard
Maintenance	Clean stylus with brush; replace stylus when worn
Safety Precautions	Handle with care; avoid dropping; keep away from magnetic fields
Repairability	Replaceable stylus (AT-VMN95ML)

Frequently Asked Questions - AT-VM95ML Audio-Technica

What is the tracking force for the AT-VM95ML?

The recommended tracking force is 2.0 g, with an acceptable range of 1.8 - 2.2 g.

What type of stylus does the AT-VM95ML use?

It uses a MicroLine stylus, which is nude-mounted for improved detail retrieval.

Is the stylus replaceable?

Yes, the stylus is replaceable. The replacement stylus model is AT-VMN95ML.

What is the output voltage of this cartridge?

The output voltage is 4.0 mV at 1 kHz and 5 cm/sec.

What load impedance should I set my phono preamp to?

The cartridge is designed for a load impedance of 47 kΩ and capacitance of 100-200 pF.

Can I use the AT-VM95ML with any turntable?

It fits any turntable with a standard 1/2-inch mount and appropriate tonearm.

How do I clean the stylus?

Use a stylus brush gently from back to front. Avoid liquids.

What is the frequency response?

The frequency response is 20 – 22,000 Hz, providing wide range.

How much does the cartridge weigh?

The cartridge weighs 6.1 g, which is typical for these models.

Does the AT-VM95ML require a battery or external power?

No, it is a passive moving magnet cartridge and does not require power.

USER MANUAL AT-VM95ML Audio-Technica

Audio-Technica Corporati

2-46-T Nish-Harulse, Machida, Tokyo 194-8606, Japan www.audio-technica.com

©2018 Audio-Technica

Global Support Contact: www.at-globalsupport.com

112301441.01.01 var.1 2018.07.01

日本語

Thank you for purchasing this Audio-Technica product. Before using the product, read through this year manual to ensure that you will use

the product, held through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference.

■ Safety precautions

- Keep the plastic bag provided with the product out of the

reach of small children and away from open flames to avoid accidents or fire.

- Keep the product out of the reach of small children to avoid accidents or malfunction.

- Do not put the product in a location where it is exposed to

direct sunlight, near heating devices, or in places with high temperatures, high humidity, or high concentrations of dust to

avoid malfunction. • Do not touch the product's contilvers, stivus tin, and magnets

- DO NOT TOUCH THE PRODUCT A CANSEVER, AYLIDE UP, AND MAGNETA TO avoid malfunction.

- Do not attempt to disassemble or modify the product to avoid malfunction.

• Do not subject the product to strong impact to avoid malfunction.

manufacture.

■ N

Become familiar with each part before using the product.

1 Protector 5 Cantilever 2 Cartridge body 6 Studus tin

2 Cartridge body 6 Stylus up 3 Output terminals 7 Magnets

4 Stylus (Replacement stylus)

■

■ How to use Remove the (replacement) style before mounting the product

1. Mount the product onto the headshell or headshell-

integrated tonearm.

1. Connect the lead tips, noting output polarity. a
2. Connect headshell lead tips to the product output terminals (a

Connect robustness load tips to the product output terminals (a shown in the figure).

- Never apply heat (from solder, etc.) to the output terminals. 3. Determine the correct position for installing the product

1. Determine the correct position for obtaining the product (adjust overhang).

- Adjust overhang following the instructions in the tonearm's, turntable's, or headshell's user manual.

If you are unsure, align the stylus tip to the cartridge originally attached to the toparm (as shown in the flexural

1. Adjust tracking force

- Confirm the tracking force for the product in "Specifications."

- Do not apply stylus pressure unnecessarily. It may not only damage the record and stylus but impair audio quality.

1. Adjust tonearm height.

- Adjust the height so that the bottom surface of the headshell is the record surface are parallel, as seen from the side. An

improper tonearm height may cause the body of the product to make contact with the record and could impair audio quality or

make contact with the record and could impair a record quality of damage the record.

1. Connect directly to the PHONO (MM) terminal of the preamplifier/amplifier

· If your preamplifier/amplifier does not have a PHONO termina

use a phono equalizer (sold separately).

71 ■ Care

- Use a brush to remove dirt and dust from the stylus tip.

· Always move the brush in the direction in which the record rotates

- A stylus cleaner (sold separately) is recommended to remo

stubborn dirt.

■ Replacing the stylus

1. Remove the replacement stylus by pulling in the direction

of the arrow without touching the cantilever, stylus tip, a magnets.

1. Install a new replacement stylus onto the cartridge body.

- Lifetime of the replacement stylus is approx. 1,000 hours.

■ Specifications

■ Specifications Type: VM

Frequency response: 20 to 25,000 Hz

Output voltage: 3.5 mV (1 kHz, 0 omsec.)
Channel separation: 23 dB (1 kHz)

Output balance: 1.5 dB (1 kHz) Tracking force: 1.8 to 2.2 n (2.0 n standard)

Coil impedance: 3.3 k ohms (1 kHz)

DC Resistance: 485 ohms Recommended load impedance: 47 k ohms

Recommended load capacitance: 100 to 200 pF Coil capacitance: 550 mH (1 kHz)

Solid substance: 500 mm (1 kg) Static compliance: 20 x 10 ^-6 cm/dyne

Dynamic complanoic: 10 x 10 ^-6 cm/syné (100 Hz) Stylus: Nude MicroLinear

Stylus curvature radius: 2.2 × 0.12 mil

Latticever: Aluminum pipe Vertical tracking angle: 23°

Dimensions: 17.2 mm (0.68") × 18.9 mm (0.74") × 28.3 mm (1.20") (H × W × D)

Weight: 6.1 g (0.22 oz)

Replacement (cylus (solid separately) ). AT-VIMRUSMC Accessories: Cartridge installation slotted screws 11.0 mm (0.43") × 2 and

8.0 mm (0.31") × 2, Washer × 2, Non-magnetic screwdriver : The replacement status of this product is used for AT-UH495 series products. In t

The replacement style in this product is easy for Mr. Wild (see) products. In a series, we offer replacement style with different stylus tip structures and point

enapet. For more details, please visit our Audio-technical website.

For product improvement, the product is subject to modification without not

Français

The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a rule line on paper). According to Rule 2, such lines must be ignored by the OCR result. The provided OCR content is "____", which consists of underscores. Underscores are not equivalent to a solid line and are not permitted under the “Stylistic/Background Lines (Ignore)” rule. Outputting underscores for a stylistic line is incorrect because it misinterprets the line as a placeholder fill-in-the-blank area. Since the OCR output incorrectly rendered a stylistic line as underscores (which should be ignored), this violates the rule. Therefore, the OCR result is inconsistent with the Ground Truth.

aob-coalt Audio-Technica.