BS 51/1 - Cooker AKO - Free user manual and instructions

USER MANUAL BS 51/1 AKO

Scanned technical diagram showing a multi-layered device with labeled components and an AKO logo in the corner.

CE

GB Assembly and operating instructions P. 5 - 6

Thank you for purchasing this appliance. You have purchased a quality product which has been manufactured to and complies with all of the recognised technical CE safety norms.

To ensure your safety and complete satisfaction with the appliance, please read the operating instructions carefully before using it. Please keep the operating instructions in a safe place and do not pass on the appliance to other persons for use unless it is accompanied by the operating instructions.

CAUTION

The following safety instructions should be observed

• This appliance may only be used for normal domestic use and not for industrial purposes. The appliance has to be fixed horizontally at the wall at least 1.8 m above the floor (see fig. 3).
• A ceiling suspension is not allowed. Wooden ceilings can turn darker due to the generation of heat of the appliance even if the minimum distance to the ceiling is observed.
• Should the appliance be installed in the bathroom, the minimum safety distances (see fig.3,4) must be observed. It must be ensured that the appliance is out of reach of persons in the shower or the bath.
• A minimum distance of 65 cm must be maintained between the front grille and flammable items (e.g. curtains), walls and other structures.
• Make sure that the appliance is not mounted directly below a wall socket.
  • The appliance may not be covered since this could lead to overheating or cause fire.
• The swivel bracket must not be adjusted while the appliance is in use! Risk of burns! Allow the appliance to cool down before adjusting the bracket.
• Permanent connection may only be carried out by a qualified electrician. Observe the respective national requirements.
• Permanent connection may only be implemented to the mains if it is isolated (on all poles). At least 3 mm isolation for the contact opening is required.
  • The appliance must be earthed.
• Do not use the appliance in rooms with easily inflammable vapours or gases.
• Check whether the voltage on the type label agrees with the voltage supply in your home.
  • The appliance may not be operated by children.
• Make sure that no water or other fluids can enter into the appliance.
• Before cleaning disconnect the appliance via the all-polo disconnecting switch.
• Never use easily inflammable cleaning agents, like petrol or ethyl alcohol, for cleaning the appliance.
• The appliance may only be opened up and repaired by qualified personnel.

Technical specifications
Technical specifications may change without prior notice

Type	BS 600/1	BK 1200/2	BK 1200/1	BS 1200/1BS 51/1	BS 1500/1BS 510/2BK 1500/1*	BS 1800/1BS 510/1	BK 2000/1
Nominal voltage	230 V~
Power	600 W	850 W	1200 W	1200 W	1500 W	1800 W	2000 W
Switching levels	0: OFF1: 600 W	0: OFF1: 850 W	0: OFF1: 1200 W	0: OFF1: 600 W1: 600 W2: 1200 W	0: OFF1: 500 W*650 W2: 1000 W*850 W3: 1500 W	0: OFF1: 600 W2: 1200 W3: 1800 W	0: OFF1: 800 W2: 1200 W3: 2000 W
Protection class	I
Type of installation	Stationary installation
Approx. Dimensions (cm;W x D x H)	51x14x8	75x9x7,5	75x9x7,5	51x14x8	51x14x8*75x9x7,5	51x14x8	75x9x7,5
Approx. Weight	2 kg

Your wall radiator warms the object or person without directly heating up the surrounding air. It contains one, two or three heating elements. The power level of the appliance can be adjusted via a switch with pull cord. The selected heating level can be read on the display.

Assembly parts (see diagrams on page 2)

① 1-3 heating elements
⑦ Cover
② Reflector
⑧ Screw
③ Protection grid
⑨ 2 Plugs (in the small bag added)
④ Display of heating levels
⑩ 2 Distance pieces (in the small bag added)
⑤ Pull cord
⑪ 2 Screws (in the small bag added)
⑥ Fixing console with connecting terminals
⑫ 2 Fixing screws

Unpacking the device

• Remove the packaging material and the transport security mechanism which protects the heating elements.
• Check the appliance for visible damage. If you should notice any damage, do not use the appliance. Please contact your dealer immediately.
• Please dispose of the packaging in an environmentally-friendly manner.

Assembling the device (see figs. 1-6)

(You require an 8mm standard screw driver and a size 2 cross-head screw driver).

Loosen screw ⑧ and take off cover ⑦ – Turn the console ⑥ through 90° backwards – Drill two holes with ∅ 6mm into the wall, for dimensions and safety distance see fig. 3 - 5. Make sure there are no other installations close to the drill holes (e. g. electric wirings, water pipes) – Fix the console ⑥ of the appliance to the wall by means of the two distance pieces ⑩, the screws ⑪ and the plugs ⑨. Let an specialist make the electric connections according to figure 6. (If the electric supply line is outside the console it must be laterally introduced into the console through the membrane bushes.) – Install cover ⑦ – Place the appliance that way so the heat is radiated into the direction desired – Fix the position by tightening the fixing screws ⑫.

Operation of the appliance

- Adjust the desired heating level by pulling the pull cord ⑤ once or several times. You can easily read the selected heating level at the display ④. When you selected the highest heating stage and pull the pull cord again, the appliance is reset to position 0 and is turned off.

Display of heating level

0 (OFF) -> 1 (Heating level 1) -> 2* (Heating level 2) -> 3* (Heating level 3) -> 0 (OFF)

*(only certain appliances)

Cleaning the device

Turn off the appliance and let it cool down.
- Disconnect the appliance via the all-polo disconnecting switch.(fuse).
- When needed, wipe the device with a slightly damp cloth.
- To remove dust from the reflector and heating elements you can use a brush with long soft bristles.
- When the device is heavily contaminated, get it cleaned by an expert.

Possible faults and causes

Fault	Cause	Remedy
The heating elements do not radiate any heat.	The device is turned off (Display Position 0).	Adjust the desired heating level.
	The relevant household fuse has blown or the circuit breaker has been activated.	Check the fuse / circuit breaker and make sure that no other high power devices share the same fuse / circuit breaker.

If you have tried all the above and the appliance still does not work, please refer to your dealer or a service centre.

Maintenance

The device is maintenance free.

Disposal

For the safe and environmentally-friendly disposal of the appliance, please contact your dealer or the manufacturer.

Chère cliente, cher client,