LEDWAVE - Lamp BeamZ - Free user manual and instructions

Product type	LED effect light lamp
Brand	BeamZ
Model	LEDWAVE
Category	Lamp
Power supply	Mains (voltage according to label on device, do not use a dimmer)
Main functions	Automatic mode, color mode, UV mode, active sound mode, flash mode, motor mode, speed and sensitivity adjustment
Control modes	Standalone (automatic programs) and infrared remote control
Remote control	Infrared with CR2025 button cell battery, remove the protective film before first use
Safety	Do not look directly at the beam, minimum distance 50 cm around the device, secure with safety cable if mounted >100 cm, do not expose to moisture or extreme heat
Maintenance	Dust regularly, clean glass components with a soft cloth and mild detergent solution, do not use solvents or abrasives
Fuse	Replaceable fuse of identical type and rating, replace after disconnecting the device
Operating conditions	Indoor only, ambient temperature between -5°C and +45°C, do not use continuously without breaks
Environmental protection	Do not dispose of with household waste, take to appropriate collection point for electrical and electronic equipment
Repairs	Repairs and electrical maintenance reserved for qualified technician

Frequently Asked Questions - LEDWAVE BeamZ

How to turn the device on and off?

Press the red button on the remote control to turn on the device, press again to switch to standby mode. Make sure the remote control is powered (remove the protective film from the battery).

How to use the remote control?

The infrared remote control allows you to select modes (Auto, Color, UV, Sound, Flash, Motor) and adjust speed and sensitivity. Point it at the device's receiver. The CR2025 button cell battery must be installed with correct polarity.

What to do if the device does not respond?

First check that the device is plugged in and powered on. If the fuse has blown, replace it with a fuse of the same type and rating. If the problem persists, contact BeamZ customer service.

How to replace the fuse?

Unplug the device. Open the fuse holder on the rear panel with a small screwdriver, remove the old fuse and insert a new identical fuse. Close the fuse holder.

How to clean the device?

Unplug the device and let it cool down completely. Use a vacuum cleaner or low-pressure compressed air to remove dust. Clean glass surfaces with a soft cloth slightly moistened with a mild detergent solution. Dry before reconnecting.

What are the operating modes?

Modes include: Auto (automatic programs), Color, UV (ultraviolet light), Active Sound (reacts to music), Flash (strobe), Motor (derby effect). You can also adjust speed and sound sensitivity.

Can I use the device outdoors?

No, this device is designed exclusively for indoor use. It must not be exposed to moisture, rain or extreme temperatures.

How to adjust sound sensitivity?

In Active Sound mode, press the SEN button on the remote control, then use the + and - buttons to increase or decrease sensitivity.

What to do if the remote control does not work?

Check that the battery protective film has been removed. If the range decreases, replace the battery with a CR2025 respecting polarity (positive pole facing up). Make sure there is no obstacle between the remote control and the device.

How to install the device at height?

For mounting height >100 cm, secure the device with a suitable safety cable to the intended attachment points. Never attach the safety cable to the transport handles. Leave at least 50 cm free space around the device for ventilation.

USER MANUAL LEDWAVE BeamZ

SAFETY INSTRUCTIONS....3

UNPACKING INSTRUCTION....4

POWERSUPPLY 4

REMOTE CONTROLLER....4

CLEANING....5

REPLACING THE FUSE 5

TROUBLE SHOOTING 6

NEDERLANDS

VEILIGHEIDSINSTRUCTIES 7

UITPAKKEN 8

AANSLUITSPANNING....8

AFSTANDSBEDIENING 8

REINIGEN 9

VERVANGEN ZEKERING....9

PROBLEMEN OPLOSSEN 10

DEUTSCH

WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation, usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit
- Please read these instructions carefully and follow the instructions.
- Observe all safety warnings. Never remove safety warnings or other information from the equipment.
- Be sure that no ventilation slots are blocked; otherwise the unit will overheated.

WARNING! Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
• Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
- Always disconnect power from the mains, when unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

- Do not switch the unit on and off in short intervals.

- Do not connect the unit to a dimmerpack.

• Install the unit in a well ventilated place.

- Never place any material over the lens.

- Never let the sunlight lights directly to the front lens, even when the unit is not working.

• Always allow free air space of at least 50 cm around the unit for ventilation.

• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the unit.

- For mounting height >100 cm, always fix the unit with an appropriate safety-rope. Fix the safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!

- Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.

- This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.

WARNING! If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat, moisture or dust.
- Clean the unit using a dry cloth.
- Do not touch the unit bare-handed during its operation (housing becomes very hot). Allow the unit to cool for at least 5 minutes before handling.
- This unit is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of fluid (does not apply to special outdoor equipment - in this case, observe the special instructions noted below). Do not expose this unit to flammable materials, fluids or gases.
- If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

- Never attempt to bypass the thermostatic switch or fuses.

- Do not dismantle or modify the unit.

- For replacement use fuses/bulb of same type and rating only.

• Repairs, servicing and electric connection must be carried out by a qualified technician.

- The ambient temperature must always be between -5^ and +45^ .

- If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.

- Plastic bags must be kept out of reach of children.

- Unit must be installed out of the reach of children. Never leave the unit running unattended.

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and

have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from

shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.

If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWERSUPPLY

The label on the backside of the unit indicates the mains voltage to which it must be connected. Check that the mains voltage corresponds to this. Any other voltage than the one indicated may cause irreparable damage to the unit. The unit must also be connected directly to the mains voltage and no dimmer or adjustable power supply may be used.

WARNING! Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to

avoid the risk of electrocution or fire.

REMOTE CONTROLLER

ON/OFF

Press the red button to turn the device on, press again to turn in standby mode.

AUTO MODE

Automatic mode will enable you to run the automatic programs on the product.

To turn on Automatic mode, press remote controller.

COLOUR MODE

To change the colour of the strobe, press

UV MODE

To put the UV light on press put the UV light off press oncein.

SOUND MODE

To turn on Sound-Active mode, press remote controller.

LASER MODE

No function.

FLASH MODE

To change the strobe with LEDs, press

MOTOR MODE

To change the derby effect.

1. Press remote controller.

2. Press <→> to change effect.

SPEED MODE

To change the speed of colour change, colour fade, sound active and strobe modes.

1. Press remote controller.

2. Press <→ to increase or decrease the speed of colour change.

SENSITIVITY MODE

To adjust sound sensitivity for in Sound-Active mode

1. Press remote controller.

2. Press + or - to either increase or decrease sound sensitivity (note: only available in sound active mode).

CAUTION! The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the

remote control. Otherwise operation of the remote control is not possible.

If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.

CLEANING

The buildup of dust, dirt and other airborne particles will reduce the unit's light output. It will also prevent the unit from cooling correctly, and this will reduce the unit's lifetime. The rate of dirt buildup will vary depending on environmental factors such as airborne dust, use of smoke machines, airflow from ventilation systems, etc. The unit's cooling fans will accelerate buildup, and any smoke particles that are present in the atmosphere will increase the tendency for dirt to clog.

To get the best performance and lifetime from the unit, inspect it regularly and clean it as soon as you see signs of dirt buildup.

Assess the operating environment each time you begin to use the unit. In dusty or smoky conditions, inspect the unit after a few hours and check it frequently the unit may attract dirt faster than you expect. Draw up a cleaning schedule that will make sure that dirt is removed before it can build up.

Use the following guidelines:

• Disconnect the unit from power and allow it to cool completely before cleaning.
• Do not use solvents, abrasives or any other aggressive product to clean the unit.
• Vacuum or use low-pressure compressed air to remove dust and loose particles from surfaces and air vents. Prevent the blades of cooling fans from turning before you aim a vacuum or air jet at the fan, or you may spin the fan too fast and damage it.
• Clean glass components by wiping gently with a soft, clean, lint-free cloth moistened with a weak detergent solution. Put the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit with a soft, clean, lint-free cloth or low-pressure compressed air before reapplying power.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

TROUBLE SHOOTING

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

SYMPTOM	POSSIBLE CAUSE	SUGGESTED ACTION
No response from unit.	No power to unit.Fuse blown or internal fault.	Check that power is turned on.Check cables and connections.Replace mean fuse or contact Beamz support or Beamz authorized service partner. Do not remove base or yoke covers. Do not attempt to replace a fuse or carry out any repairs or service that are not described in this User Manual unless you have both authorization from Beamz support or Beamz authorized service partner.
Light output cuts out intermittently.	Unit too hot.LEDs damaged.The power supply settings do not match local AC voltage and frequency.	Allow unit to cool. Reduce ambient temperature. Ensure free airflow around unit.Clean unit if necessary.Disconnect unit and contact Beamz support or Beamz authorized service partner.Disconnect unit. Check settings and correct if necessary.

VEILIGHEIDSINSTRUCTIES

REPLACEMENT DU FUSIBLE

Light source : 5-in-1 LED

LED colours : Red, Green, Blue, White, Ultra Violet

Quantity of strobe LEDs : 4

Beam angle : 6

Modes : Automatic programs

Power consumption : 0.5 - 0.2A

Power supply : 100-240VAC 50/60Hz

Dimensions (L x W x H) : 240 x 130 x 112

Weight : 1.60 kg

Design and product specifications are subject to change without prior notice.

The products referred to in this manual conform to the European Community Directives to which they are subject:

European Union

Tronios B.V.,

7602KR Almelo, The Netherlands

2014/35/EU

2014/30/EU

2011/65/EC

United Kingdom

Tronios Ltd.,

130 Harley Street,

London W1G 7JU, United Kingdom

S.I. 2016:1101

S.I. 2016:1091

S.I. 2012:3032

BEAMZ

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX effects, static washes, sound-activated club effects, strobes & blacklights, LED lighting, fog and special effects machines, lasers and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.