NorBreeze MISTRAL 70 SW - Range hood NODOR - Free user manual and instructions

Product Type	Kitchen Hood
Brand	Nodor
Model	NorBreeze MISTRAL 70 SW
Width	70 cm
Control Type	Touch
Display	LED
Number of Speeds	5 speeds + Boost (full power 5 min)
Lighting	LED adjustable brightness (L1 to L5) and temperature (cool/warm)
Timer	Yes, progressive automatic shut-off (max cycle 15 min)
Evacuation Mode	Extraction or recirculation with charcoal filter
Grease Filter	Reusable, washable
Charcoal Filter	Optional, disposable or reusable depending on model
Filter Cleaning Alert	Yes, flashing timer icon
Material	Stainless steel
Installation	Wall-mounted, exhaust duct or recirculation
Power Supply	220-240 V, 50 Hz
Maintenance	Regular cleaning of grease filters, replacement of charcoal filter if recirculation

Frequently Asked Questions - NorBreeze MISTRAL 70 SW NODOR

How to set the timer on the NorBreeze MISTRAL 70 SW hood?

To activate the timer, press the timer icon (ⓣ) when the motor is running. The cycle starts with 5 minutes at the current speed, then decreases by one level every 2 minutes until stop. To cancel, press the icon again.

How to change the lighting temperature (cool/warm)?

Put the hood in setting mode (hood off, simultaneously press the ∧ and ∨ icons). Then press the lighting icon (☐) until it turns red. Use ∨ or ∧ to choose between cool (_) or warm (≡) mode, then press the lighting icon to confirm.

What does the red flashing of the timer icon mean?

It is a filter cleaning alert. If the display shows — (extraction mode), clean the grease filters. If the display shows ≡ (recirculation mode), clean or replace the charcoal filter. After intervention, press the timer icon to turn off the alert.

How to switch from extraction mode to recirculation mode?

Access the setting mode (hood off, simultaneously press ∧ and ∨). Press the timer icon (ⓣ) which lights up red. The screen displays the current mode: — for extraction, ≡ for recirculation. Use ∨ or ∧ to change, then press ⓣ to confirm.

How to activate the Boost function?

At any speed (1 to 5), press the speed increase icon (∧) for more than 2 seconds. The hood goes to full power (P) for 5 minutes, then automatically returns to speed 5.

Why is the hood vibrating excessively?

Possible causes are: incorrect installation on the supports (check the mounting), a damaged fan blade, or a poorly fixed motor. Remove the appliance and ensure it is correctly installed.

The lighting works but the fan does not turn, what to do?

Check that the fan blade is not blocked (object or grease). If it is free, the motor may be damaged. Contact customer service if the problem persists.

How to adjust the brightness of the lighting?

Press and hold the lighting icon (☐) until the screen displays a level from L1 to L5. Release when the desired brightness is reached. The setting is saved.

Cooking odors persist despite the hood running, why?

In recirculation mode, the charcoal filter may be saturated or missing. Install or replace the charcoal filter. Also check that the exhaust duct is not blocked or deformed.

How to clean the grease filters?

The grease filters are reusable. Wash them by hand with mild detergent or in the dishwasher (max temperature 65°C). Dry them well before reinstalling.

USER MANUAL NorBreeze MISTRAL 70 SW NODOR

EN IMPORTANT - Please read carefully the separate safety guide before use.

WARNING: Read the instructions before using the appliance

FUNCTIONS & SETTINGS

CONTROL PANEL

To obtain the best results from your cooker hood it is recommended that you leave it switched on for a short time after you have finished cooking.

	Timer
	ON, Fan Boost Function and Fan speed increase
	LED display
	OFF and Fan speed decrease
	Light ON /OFF

SETTINGS

Once the appliance is switched off press both, increase ( ) and decrease fan speed ( ) icons. All icons will start blinking in White. The hood is now in setting mode.

IMPORTANT: Once in settings mode, you can adjust the recirculation and lighting options in any order. However, all actions must be completed within two minutes.

SETTING THE DUCTED OR RECIRCULATION MODE

Once in setting mode, press the Timer (💡) icon and it will blink in red. The LED display will show the current Ducted or Recirculation mode.

Ducted mode: (−) Default setting to extract air to the outside.

Recirculation mode: (≡) Setting to recirculate the air with carbon filters installed.

To change this option press either (∨) or (∧) to select the correct mode and then press Timer(💡) icon to accept the change.

SETTING THE LIGHTING MODE

Once in setting mode, press the Light ( ) icon and it will blink in red. The LED display will show the current lighting mode.

Cool light: (_) Default setting for all lights.

Warm light: (≡) Optional setting for all lights.

To change these settings press (∨) or (∧) and press the Light (💡) icon to accept the change.

GENERAL USE

ON/OFF AND INCREASE/DECREASE THE FAN SPEED

Press the decrease fan speed ( √ ) icon and the fan will turn on at speed 1.

Press the increase fan speed icon ( ) and the fan will turn on at maximum speed (Booster)

If the fan motor is set at speeds 2,3,4, 5 or P, pressing the Fan Decrease (√) Icon will reduce the speed by one level at a time. If you press the Fan Decrease (√) Icon for more than three seconds, the fan will turn down. However, the downlight will remain on 8 if enabled).

If the fan motor is set at speed 1, pressing the Fan Decrease ( ) Icon the motor will switch off. However, the downlight will remain on (if enabled) and the display will show the current brightness level.

Boost Function

If the fan motor is set at speeds 1,2,3,4 or 5, pressing the Fan Increase ( ) Icon will increase the speed by one at a time. If you press the Fan Increase ( ) Icon for more than two seconds, the speed will increase to full power from any level and the display will flash “P”

NOTA: Full power or Boost (P) only operates for five minutes maximum to conserve energy and the fan speed will automatically drop to speed level 5 after this time.

Light On/Off ( )

Touch the Light ( 🔊 ) Icon to turn on the downlight.

To change the brightness of the downlight, touch and hold the Light (💡) Icon until the display show the brightness sequence. Remove your finger from the Light (💡) Icon when the desired brightness is achieved. The sequence runs from L1 to L5 and back to L1 in steps. The selected brightness will flash for a few seconds and revert to the fan speed display. This lighting setting will be kept for future uses.

Setting the timer ( ⏚ )

- When the fan motor is on and the Timer ( ), icon is pressed the icon will turn in red and the display will show the current fan speed.

- The chosen speed level will remain in use for five minutes before dropping down

EN

to the next lowest speed. This speed will remain in operation for two minutes before dropping down again. This will be repeated every two minutes unless the speed is already at level 1 and then the fan will turn off. If the light is already on, this will also be turned off.

• Pressing the Fan Decrease ( ) Icon or Fan Increase ( ^ ) Icon during a current timer program will restart the countdown process again with the first five minutes cycle.
• If the Timer (💡) icon is pressed again during a current timer program, the cycle will be cancelled. The Timer (💡) Icon will revert to white and the current fan speed will remain on indefinitely.
• The maximum timer program cycle is 15 minutes: 5 minutes: 5 minutes on 0 and then 2 minutes each on speed 5 down to speed 1.

Filter cleaning warning

Once the cooker hood is off, if the Timer icon (💡) blinks in red and LED display shows “(−)”, you should clean the filters. Once they are cleaned or replaced, press the Timer (💡) icon again and the icon will turn off.

(Only in Recirculation mode). Once the cooker hood is off, if Timer (💡) icon blinks in red and the LED display shows “(≡ )”, you should clean the carbon filters (in case you are using washable carbon filters) or replace them ( in case you are using disposable carbon filters). Once they are cleaned or replaced, press the Timer (💡) icon again and the icon will turn off.

Problem Possible cause Solution
Excessive vibration. The appliance	ce is not installed properly on the brackets.	Take down the appliance and check it is properly fixed.
	The fan blade is damaged. Switch	ch off the appliance. Repair to be carried out by qualified service personnel only.
	The fan motor is not fixed tightly.
The light is on, but the fan does not work.	The fan blade is jammed.
	The motor is damaged.
Both the light and motor do not work.	Light bulb blown. Contact Customer Services on.
	Power connection loose. Check power supply.
Suction performance reduced.	Speed may be too low. Select a higher speed.
	Optional vent kit might be twisted.	Ensure that the vent kit is fitted according to the manufacturer's instructions.
	Top vent might be obstructed.	Clear any obstruction.
	The installation may not comply with the manufacturers instructions.	The vent hose should be correct diameter throughout with no reductions or restriction. (See installation section).
Works normally but cooking smells linger.	Carbon filter is not fitted in recirculation mode or is full of grease.	Fit carbon filter or replace the carbon filter (See Care and maintenance section).
The hood does not work Check	that the hood is connected to power. Check that the fuses or automatic have not jumped.
The hood still does not work	If, after having checked the points mentioned above, your problem has not yet been solved, contact the technical service or your distributor.