THERMO FH2 - Thermometer THOMSON - Free user manual and instructions

Product type	Non-contact infrared forehead thermometer
Brand	Thomson
Model	THERMO FH2
Dimensions	34 x 160 x 50 mm
Weight (without batteries)	Approx. 68 g
Power supply	2 AAA alkaline batteries (not included)
Body measurement range	34.0 °C to 43.0 °C (93.2 °F to 109.4 °F)
Object measurement range	0 °C to 93.2 °C (32 °F to 199.7 °F)
Accuracy (body 35-42 °C)	±0.2 °C
Resolution	0.1 °C / °F
Measurement time	Approx. 1 second
Memory	Last 9 measurements
Display	Backlit LCD screen with 3 colors (green, orange, red)
Sound signal	Can be disabled
Automatic shut-off	After 30 seconds
Recommended measuring distance	3 to 5 cm from the forehead
Units of measurement	°C or °F (switchable)
Operating ambient temperature	10 °C to 40 °C, humidity 15%-93%
Storage temperature	-25 °C to 55 °C, humidity 0%-93%
Care and cleaning	Clean the sensor with a cotton swab dipped in 70% isopropyl alcohol
Safety	Do not disassemble, do not immerse, keep out of reach of children
Spare parts and repairability	No detachable parts, sealed device
General information	Intended use: measurement of human body temperature on the forehead. Does not replace a medical diagnosis.

Frequently Asked Questions - THERMO FH2 THOMSON

How to turn on the THERMO FH2 thermometer?

Press the power button (square icon with a circle). The screen lights up and briefly shows the last measurement, then three dashes appear indicating the device is ready.

How to install or replace the batteries?

Press the curved part of the battery compartment cover to open it. Insert two AAA alkaline batteries following the indicated polarities. Close the cover.

What do the error messages 'HI' and 'LO' mean?

'HI' appears if the measured temperature exceeds 43 °C (body) or 93.2 °C (object). 'LO' appears if it is below 34 °C (body) or 0 °C (object). Check the distance and cleanliness of the sensor.

How to clean the infrared sensor?

Use a cotton swab or a soft cloth moistened with 70% isopropyl alcohol to gently clean the sensor lens. Do not use abrasive paper and do not let liquid enter the thermometer.

At what distance should I place the thermometer from the forehead?

Hold the thermometer at a distance of 3 to 5 cm from the center of the forehead, just above the eyebrows. Press the measurement button and wait for the beep (if enabled).

What do the screen colors mean after a measurement?

Green: normal temperature (34-37.2 °C). Orange: mild fever (37.2-38.2 °C). Red: high fever (38.2-43 °C). A red screen with 'HI' indicates a temperature above 43 °C.

How to view the last 9 measurements in memory?

When the device is off, press the memory button (folder icon). Each press displays the previous measurement. The device turns off automatically after 30 seconds or by pressing the power button.

Can I measure the temperature of food or a bath?

Yes, hold down the measurement button for 6 seconds to switch to 'non-body' mode. The screen displays an appropriate symbol. Point at the object and briefly press the measurement button.

How to switch between Celsius and Fahrenheit?

Turn off the device. Press the memory button for 6 seconds until the unit blinks. Press memory again to change the unit, then wait 8 seconds or press the power button to confirm.

What does the warranty cover and how to claim it?

The warranty is 2 years from the date of purchase. It covers defects in materials and workmanship under normal use. To claim it, contact the distributor where you purchased the product with the receipt as proof of purchase.

USER MANUAL THERMO FH2 THOMSON

Shenzen Pango Electronic Co., Ltd

N°25 1st industry zone, Fenghuang road, Xikeng village, Henggang town,

Longgang district, Shenzhen, Guangdong China

Authorised representative :

Imported and distributed by :

STAB XTOM SARL, 46 avenue des Frères Lumière, 78190 Trappes - France.

This product has been manufactured and sold under the responsibility of Bigben Interactive, THOMSON, and the THOMSON logo are trademarks of Technicolor (S.A.) or its affiliates and are used under license by Bigben Interactive.

Any other product, service, company, trade or product name and logo referenced herein are neither endorsed nor sponsored by Technicolor (S.A.) or its affiliates.

Date: 2019-01-09

Rev : A/1

0197

Appendix 1 Guidance and Manufacturer Declaration Tables

Guidance and manufacturer's declaration-electromagnetic emissions
The Model THERMO F42 Infrared Thermometer the electromagnetic environment specified below. The customer or the user of the Model THERMO FH2 Infrared Thermometer should assure that it is used in such an environment.
Emissions	Compliance	Electromagnetic environment-guidance
RF emissions CISPR 11	Group 1	The Model THERMO FH2 Infrared Thermometer uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF emissions CISPR 11	Class B	The Model THERMO FH2 Infrared Thermometer is used in home and it's powered by DC 3V
Harmonic emissions IEC 61000-3-2	N. A.
Voltage fluctuations/ flicker emissions IEC 61000-3-3	N. A.

Guidance and manufacturer's declaration – electromagnetic immunity
The Model THERMO For Use Infrared Thermometer the electromagnetic environment specified below. The customer or the user of the Model THERMO FH2 Infrared Thermometer should assure that it is used in such an environment.
Immunity test	IEC 60601 test level	Compliance level	Electromagnetic environment-guidance
Electrostatic discharge (ESD)IEC 61000-4-2	±8 kV contact ±2 kV, ±4 kV, ±8 kV, ±15 KV air	±8 kV contact ±2 kV, ±4 kV, ±8 kV, ±15 KV air	Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %.
Power frequency (50/60 Hz) magnetic field IEC 61000-4-8	30 A/m, 50/60Hz	30 A/m, 50/60Hz	Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
NOTE U is the a.c. mains voltage prior to application of the test leve

Guidance and manufacturer's declaration – electromagnetic immunity
The Model THERMO FHK2 Infrared Thermometerthe electromagnetic environment specified below. The customer or theuser of the Model THERMO FH2 Infrared Thermometer should assurethat it is used in such an environment.
Immunity test	IEC 60601test level	Compliance level	Electromagnetic environment - guidance
Conducted RF IEC61000-4-6	3 Vrms150 kHz to 80 MHz 6 Vrms150 kHz to 80 MHz outside ISM bandsa	N/A	Portable and mobile RF communications equipment should be used no closer to any part of the Model THERMO FH2 Infrared Thermometer, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.Recommended separation distance d = [ 3.5V_1 ] d = [ 3.5E_1 ] 80MHz to 800MHz d = [ 7E_1 ] 800MHz to 2.7GHzwhere P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres(m).Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, ^a should be less than the compliance level in each frequency range ^b Interference may occur in the vicinity of equipment marked with the following symbol:
Radiated RF IEC61000-4-3	10 V/m80 MHz to 2.7 GHz	10 V/m

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

a The ISM (industrial, scientific and medical) bands between 0,15 MHz and 80 MHz are 6,765 MHz to 6,795 MHz; 13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz. The amateur radio bands between 0,15 MHz and 80 MHz are 1,8 MHz to 2,0 MHz, 3,5 MHz to 4,0 MHz, 5,3 MHz to 5,4 MHz, 7 MHz to 7,3 MHz, 10,1 MHz to 10,15 MHz, 14 MHz to 14,2 MHz, 18,07 MHz to 18,17 MHz, 21,0 MHz to 21,4 MHz, 24,89 MHz to 24,99 MHz, 28,0 MHz to 29,7 MHz and 50,0 MHz to 54,0 MHz.

b The compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency range 80 MHz to 2,7 GHz are intended to decrease the likelihood that mobile/portable communications equipment could cause interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 has been incorporated into the formulae used in calculating the recommended separation distance for transmitters in these frequency ranges.

c Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Model THERMO FH2 Infrared Thermometer is used exceeds the applicable RF compliance level above, the Model THERMO FH2 Infrared Thermometer should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the Model THERMO FH2 Infrared Thermometer.

d Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Recommended separation distances between portable and mobile RF communications equipment and the Model THERMO FH2 Infrared Thermometer
The Mode in THERMO or FH2 Infrared Thermometer an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the Model THERMO FH2 Infrar Thermometer can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Model THERMO FH Infrared Thermometer as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output of transmitter W	Separation distance according to frequency of transmitter m
	150 kHz to 80 MHz d = [ 3.5V_1 ]	80 MHz to 800 MHz d = [ 3.5E_1 ]	800 MHz to 2.7 GHz d = [ 7E_1 ]
0.01	0.12	0.12	0.23
0.1	0.38	0.38	0.73
1	1.2	1.2	2.3
10	3.8	3.8	7.3
100	12	12	23
For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, when P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.NOTE 2 These guidelines may not apply in all situations.Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Garantie :