cruZer 2 2778 - Shaver BRAUN - Free user manual and instructions

USER MANUAL cruZer 2 2778 BRAUN

5734320_Cruzer2778_MN.indd 85734320_Cruzer2778_MN.indd 8 22.09.2006 11:17:23 Uhr22.09.2006 11:17:23 Uhr9 English Our products are designed to meet the highest standards of quality, functionality and design. We hope you entirely enjoy your new Braun shaver. Warning Your shaver is provided with a special cord set with an integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it. Otherwise there is risk of electric shock. Description 1 Foil protection cap 2 Shaver foil 3 Cutter block 4 Rotating styler 4a Wide shaper (28 mm) 4b Narrow shaper (14 mm) 5 Charging light 6 On/off switch 7 Special cord set Charging The best environmental temperature for charging is between 15 °C and 35 °C. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time. Using the special cord set, connect the shaver to an electrical outlet with the motor switched off. When charging for the first time, leave the shaver to charge continuously for 4 hours. The green charging light (5) shows that the shaver is being charged. When the battery is fully charged, the charging light intermittently blinks on and off. This indicates that the battery maintains its full capacity. A full charge provides 30 minutes of cordless shaving time depending on your beard growth. Once the shaver is completely charged, discharge the shaver through normal use. Then recharge to full capacity. Subsequent charges will take about 1 hour. Maximum battery capacity will only be reached after several charging/discharging cycles. If the rechargeable batteries are discharged, you may also shave by connecting the shaver to an electrical outlet via the special cord set.

5734320_Cruzer2778_MN.indd 95734320_Cruzer2778_MN.indd 9 22.09.2006 11:17:23 Uhr22.09.2006 11:17:23 Uhr10 Shaving Remove the foil protection cap (1). Activate the on/off switch (6). The floating foil frame automatically adapts to your skin surface for a close, smooth shave. For best results: Always shave before washing your face. At all times, hold the shaver at right angles (90°) to the skin (b). Stretch the skin and shave against the direction of hair growth. For pre-shaving after a few days of not having shaved, use the wide shaper (4a) to pre-cut long hairs. For a close, smooth shave, finish with the foil. To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. Using the rotating styler (4) The wide shaper (4a) evenly cuts and trims large areas (c). It is ideal for shaping sideburns, moustaches and partial short beards. The wide shaper is provided with safety rips and a gliding strip for less irritation and easy gliding. Press the green stripes to push up the rotating styler (4). While stretching the skin, guide the wide shaper against the direction of hair growth. The narrow shaper (4b) precisely defines lines and edges (d), being ideal for precise contouring. To use the narrow shaper, push up the styler and turn it 180°. Frequent use of the styler (4) will reduce the battery capacity. Cleaning This appliance is suitable for cleaning under an open water tap.

Warning: Detach the hand-held part from the power

supply before cleaning it in water. Regular cleaning ensures better shaving performance. Rinsing the shaving head after each shave under running water is an easy and fast way to keep it clean: Switch the shaver on (cordless) and rinse the shaving head under hot running water (e). A natural based soap may also be used provided it contains no particles or abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

5734320_Cruzer2778_MN.indd 105734320_Cruzer2778_MN.indd 10 22.09.2006 11:17:23 Uhr22.09.2006 11:17:23 Uhr11 Next, switch off the shaver, remove the shaver foil and the cutter block. Then leave the disassembled shaving parts to dry. If you regularly clean the shaver under water, then once a week apply a drop of light machine oil onto the long hair trimmer and shaver foil (g). Alternatively, you may clean the shaver using the brush provided (f): Switch off the shaver. Remove the shaver foil. Using the brush, clean the cutter block and the inner area of the shaver head. However, do not clean the shaver foil with the brush as this may damage the foil. Keeping your shaver in top shape Replacing the shaving parts To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil and cutter block: 2000 series) Preserving the batteries In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every 6 months approximately. Then recharge the shaver to full capacity. Environmental notice This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country. Subject to change without notice. This product conforms to the European Directives EMC 89/336/EEC and Low Voltage 73/23/EEC. For electric specifications, see printing on the special cord set.