DTLS010B - Electric heater Vevor - Free user manual and instructions

USER MANUAL DTLS010B Vevor

EH UHSODFHG EHIRUH XVLQJ

$OZD\V VZLWFK RII EHIRUH UHPRYLQJ SOXJ IURP WKH RXWOHW $OZD\V VZLWFK RII EHIRUH WU\LQJ WR PRYH WKH ZD[ PHOWHU 5HPRYH WKH SOXJ E\ JUDVSLQJ WKH SOXJ 'R 127 SXOO WKH FRUG 'R QRW OHW FRUG KDQJ RYHU HGJH RI FRXQWHU 3ODFH WKH ZD[ PHOWHU VHFXUHO\ LQ FHQWHU RI FRXQWHU RU ZRUN VSDFH˺ ɣ ˺

1HYHU SODFH RQ D WLOWHG VXUIDFH

UHSODFHG UHSDLUHG E\ D TXDOLILHG HOHFWULFLDQ

or lack of experience or knowledge, unless they have been given supervision or instruction concerning the safe use of the appliance by a person responsible for their safety. FCC Information: CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment!This device complies with

Part 15 of the FCC Rules. Operation is subject to the following

two conditions: This product may cause harmful interference. This product must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this product not

expressly approved by the party.responsible for compliance could void the user's authority to operate the product.Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interfer- ence to radio or television reception,which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following mea- sures.

• Reorient or relocate the receiving antenna.

• Increase the distance between the product and receiver.

• Connect the product to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for assistance.- 5 - PRIOR TO FIRST USE: Remove all packaging from the inside and outside of the wax melter

4. Replace the lid and turn clockwise to lock into place.

5. Connect the plug to the socket.

6. Switch ON. The Red "Heating" pilot lamp will light up and the wax

7. The wax will reach the set thermostat temperature.

8. Stand your cup on the hold close to the faucet to prevent splashing

10.When the wax is topped up the wax melter will automatically reboil. 11.When the wax is completely melted,turn the appliance off and unp lug it from the electric outlet,pour out all the wax. 12.Make sure at least 500ml wax in the tank when heating to prevent a boil-dry accident. 13.The melter can be very heavy when filled with wax. Melter should not be carried or moved when full of wax as the weight and unsteady load can cause injury or strain. Melter should be placed in their position of use and filled through several trips with a smaller, manageable container (eg a jug). To ensure operator safety in lifting the mac hines, Melter should never be moved when filled with more than 5L (5L =5Kg approximately).

The appliance is protected by a thermal limiter with automatically re- set function to prevent accidental dry-boil. .If the wax in the tank is boiled dry , this is activated, the appliance will turn itself off, although the lamp with remain on. The appliance must be unplugged before it can be reset. To reset the appliance, wait until the appliance has cooled down, the n power on the appliance again, check if the heating pilot light is on. If the pilot light is on, it indicates the unit has recovered to normal working condition; if the light is still off, unplug the cord and try to power on again. Repeat this operation several times until the appliance is under normal working condition. This facility is for the protection of the user as well as the components. In case of such repeated incidents the bi-metal may malfunction causing damage of ther mal limiter as well as the heating element- 7 - beyond repair. Please note that the manufacturer will not guarantee for such negligent use of appliance. If resetting this thermal cut-out does not switch the appliance back on, please call for service or professional maintenance agent to have further check. This safety device may have been switched off during transport, if so reset the thermal cut-off following the above instructions. THERMAL CUT-OUT The appliance is fitted with a thermal cut-out to have double safety protection .When the wax is boiled dry and the boil dry protections fails to work ,the thermal cut-out will work ,then the appliance stops working. The cut out temperature is 240ć This thermal cut-out is a disposable part. When this part comes into effect, it will be broken and cannot be used again. The appliance should be brought to authorized agent to replace the thermal cut-out.

CLEANING AND MAINTENANCE

A. Only perform cleaning once the plug has been removed and the wax m elter has completely cooled down. B. Never immerse the wax melter into water. C. Pore hot water into the melter, brush sides, Melt the wax completely then pour out the water. D. Do not use any cleaning products which can cause a health hazard. E. Use a soft cloth to wipe the urn body dry. Do not use abrasive materials to avoid scratches.- 8 - items Description 1 Name Wax melting barrel 2 Model DTL-S007(A) DTL-S007(C) DTL-S007(B)

Machine Translated by GoogleCZYSZCZENIE I KONSERWACJA

Machine Translated by GoogleINTERRUTTORE TERMICO

Machine Translated by Google- 6 -

Machine Translated by GoogleTROCKENKOCHSCHUTZ

Machine Translated by GoogleMachine Translated by GoogleMachine Translated by GoogleMachine Translated by Google