NX58M9960PS - Oven SAMSUNG - Free user manual and instructions

★ ★ ★ ★ ★ 8.0/10 📄 132 pages PDF ⬇️ EN 💬 AI Question 🖨️ Print

USER MANUAL NX58M9960PS SAMSUNG

30" Gas Pro Range User manual NX58M9960P* NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 1 2019-02-27 2:26:122 English ANTITIP DEVICE WARNING To reduce the risk of tipping the range, the range must be secured by a properly installed Anti-Tip device. AFTER THE RANGE HAS BEEN INSTALLED, CONFIRM THAT THE ANTI-TIP DEVICE HAS BEEN PROPERLY INSTALLED AND VERIFY THAT THE ANTI-TIP DEVICE IS PROPERLY ENGAGED. Refer to the installation manual for instructions. a) If the anti-tip device is not installed, a child or adult can tip the range and be killed. b) Verify the anti-tip device has been properly installed and engaged at the right rear (or left rear) of the range bottom. c) If you move the range and then move it back into place, ensure the anti-tip device is re-engaged at the right or left rear of the range bottom. d) Do not operate the range without the anti-tip device in place and engaged. e) Failure to do so can result in death or serious burns to children or adults.

WARNING: If the information in this manual is not followed

exactly, a re or explosion may result causing property damage, personal injury, or death.

• DO NOT store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS: - DO NOT try to light any appliance. - DO NOT touch any electrical switch. - DO NOT use any phone in your building. - Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. - If you cannot reach your gas supplier, call the re department.

• Installation and service must be performed by a qualied installer, service agency, or the gas supplier. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 2 2019-02-27 2:26:12English 3 WARNING Do not step, lean, or sit on the oven door of the range. You can cause the range to tip, resulting in burns or serious injuries. Conrm that the Anti-Tip device is installed properly. Then, to verify that the Anti-Tip device is engaged, grasp the top rear edge of the range and carefully attempt to tilt it forward. The Anti-Tip device should prevent the range from tilting forward more than a few inches. If you pull the range out from the wall for any reason, make sure the anti-tip device is properly engaged when you push the range back against the wall. If it is not, there is a risk of the range tipping over and causing injury if you or a child stand, sit or lean on an open door. Never completely remove the leveling legs. If you remove the leveling legs, the range will not be secured to the anti-tip device properly. KEY FEATURES Bigger is better With a capacity of 5.8 cubic feet, this Samsung gas oven range offers more space than many other leading brand in the United States and Canadian markets. The enhanced capacity means a better cooking experience. A cooktop with 4 burners Power burners and simmer burners provide exible cooktop heat for a variety of cookware. Enhanced convenience with easy maintenance The Samsung gas oven range combines all the benets of 2 separate home appliances - gas range and gas oven - to maximize customer convenience with its careful, stylish design. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 3 2019-02-27 2:26:124 English Contents ContentsContents Important safety information 5 Symbols used in this manual 5 Commonwealth of Massachusetts 5 General safety 5 Fire safety 6 Gas safety 7 Electrical and grounding safety 7 Installation safety 8 Location safety 8 Cooktop safety 9 Oven safety 11 Self-cleaning oven safety 11 Overview 12 Layout 12 What’s included 12 Mode selector knob 13 Before you start 13 Oven vent/Cooling vent 13 Gas range 14 Cookware 14 Wok grate 15 Gas burners 15 Ignition 16 Gas oven 17 Cooking mode 17 Recipe guide 19 Racks 20 Special features 21 Other features 22 Using the smart connect feature 23 Using the hood control feature 24 Maintenance 26 Cleaning 26 Gliding rack 26 Door 27 Surface burners 28 Self-cleaning 30 Replacing the oven lights 31 Oven door: remove and re-install 32 Troubleshooting 33 Troubleshooting 33 Information codes 36 Warranty (U.S.A) 37 Warranty (CANADA) 39

• All electrical and gas equipment with moving parts can be dangerous. Please read the important safety information for this appliance in this manual. The instructions must be followed to minimize the risk of injury, death, or property damage.

• Save this manual. Please Do Not Discard. Symbols used in this manual WARNING Hazards or unsafe practices that may result in severe personal injury or death. CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. NOTE Useful tips and instructions. These warning icons and symbols are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference. California Proposition 65 Warning WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Commonwealth of Massachusetts

• This product must be installed by a licensed plumber or gas tter qualied or licensed by the State of Massachusetts. When using ball-type gas shut-off valves, you must use the T-handle type. Multiple exible gas lines must not be connected in series. General safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Do not touch any part of the range, including but not limited to, oven burners, surface burners, interior surfaces, and exterior surfaces except the knobs and handle during or immediately after cooking.

• Know the location of the gas shut-off valve and how to shut it off.

• Make sure the anti-tip device is properly installed on the range. See the installation instructions for more information.

• Do not let children near the range. Do not let children go into the range or onto the range. Do not let children play with the range or any part(s) of the range. Do not leave children unattended in an area where the range is in use.

• Remove all packaging materials from the range before operating to prevent ignition of these materials. Keep all packaging materials out of children’s reach. Properly dispose the packaging materials after the range is unpacked.

• Do not store any object of interest to children on the cooktop or backguard of the range. Children climbing on the range to reach items could be killed or seriously injured. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 5 2019-02-27 2:26:126 English Important safety information Important safety information

• Do not operate the range if the range or any part of the range is damaged, malfunctioning, or missing parts.

• Do not use the range as a space heater. Use the range for cooking only.

• Do not use oven cleaners or oven liners in or around any part of the oven.

• Use only dry pot holders. Pot holders with moisture in them can release steam and cause burns if they come in contact with hot surfaces. Keep pot holders away from open ames when lifting cookware. Never use a towel or bulky cloth in place of a pot holder.

• Do not use the range to heat unopened food containers.

• Do not strike the oven glass.

• When disposing of the range, cut off the power cord and remove the door to prevent children and animals from getting trapped.

• Unplug or disconnect power before servicing.

• Make sure all meat and poultry is cooked thoroughly. Meat should always be cooked to an internal temperature of 160 °F (71 °C). Poultry should always be cooked to an internal temperature of 180 °F (82 °C).

• Teach children not to touch or play with the controls or any part of the range.

• Do not lean on the range as you may turn the control knobs inattentively.

• Do not stand on top of the appliance or place objects (such as laundry, an oven cover, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance. - Items, such as a cloth, may get caught in the door. - This may result in electric shock, re, problems with the product, or injury. Fire safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Do not store, place, or use ammable or combustible materials such as paper, plastic, pot holders, linens, curtains, gasoline or other ammable vapors or liquids near the range.

• Do not wear loose tting or hanging garments while using the range.

• To avoid grease buildup, regularly clean the vents.

• Do not let pot holders or other ammable materials touch a heating element. Do not use a towel or other bulky cloths in place of a pot holder.

• Do not use water on a grease re. To put out a grease re, turn off the heat source and smother the re with a tight-tting lid or use a multipurpose dry chemical or foam-type re extinguisher.

• If a grease re should occur in the oven, turn off the oven by turning both the mode and temperature selector knobs to the OFF position.

• Keep the oven door closed until the re goes out.

• If necessary, use a multipurpose dry chemical or foam-type re extinguisher.

• Do not heat unopened food containers. The buildup of pressure may cause the container to burst and result in injury.

• Do not put any combustible material or items near the range. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 6 2019-02-27 2:26:12English 7 Important safety information Electrical and grounding safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Plug into a grounded 3-prong outlet.

• Do not remove the ground prong.

• Do not use an adapter or an extension cord.

• Do not use a damaged power plug, power cord, or loose power outlet.

• Do not modify the power plug, power cord, or power outlet in any way.

• Do not put a fuse in a neutral or ground circuit.

• Use a dedicated 120-volt, 60-Hz, 10-amp, AC, fused electrical circuit for this range. A time-delay fuse or circuit breaker is recommended. Do not plug more than one appliance into this circuit.

• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

• This range must be Earth grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path for the electric current. This range is equipped with a cord having a grounding plug. The plug must be rmly plugged into an outlet that is properly installed and grounded in accordance with the local codes and ordinances. If you are unsure whether your electrical outlet is properly grounded, have it checked by a licensed electrician.

• The range is supplied with a 3-pronged grounded plug. This cord must be plugged into a mating, grounded 3-prong outlet that meets all local codes and ordinances. If codes permit the use of a separate ground wire, we recommend that a qualied electrician determine the proper path for this ground wire. Gas safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions. If you smell gas

• Close the valve and do not use the range.

• Do not light a match, candle, or cigarette.

• Do not turn on any gas or electric appliances.

• Do not touch any electrical switches or plug a power cord into an outlet.

• Do not use any phone in your building.

• Evacuate the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department. Checking for gas leaks

• Leak testing of the appliance must be conducted according to the manufacturer’s instructions. Do not use a ame to check for gas leaks. Use a brush to spread a soapy water mixture around the area you are checking. If there is a gas leak, you will see small bubbles in the soapy water mixture at the leak point. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 7 2019-02-27 2:26:138 English Important safety information Important safety information

• Make sure your range is correctly installed and adjusted by a qualied service technician or installer for the type of gas (natural or LP) you will use. For your range to utilize LP gas, the installer must replace the 5 surface burner orices and 2 oven orices with the provided LP orice set, and reverse the GPR adapter. These adjustments must be made by a qualied service technician in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. The qualied agency performing this work assumes the gas conversion responsibility.

• Installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This range has been design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian Gas Association according to CAN/CGA-1.1, latest edition. Location safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• This range is for indoor, household use only. Do not install the range in areas exposed to the weather and/or water.

• Do not install the range in a place which is exposed to a strong draft.

• Electrical service to the range must conform to local codes. Barring local codes, it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions.

• It is the personal responsibility of the range owner to provide the correct electrical service for this range. Installation safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Have your range installed and properly grounded by a qualied installer, in accordance with the installation instructions. Any adjustment and service should be performed only by qualied gas range installers or service technicians.

• Do not attempt to service, modify, or replace your range or any part of your range unless it is specically recommended in this manual. All other service should be referred to a qualied technician.

• Always use new exible connectors when installing a gas appliance. Do not use old exible connectors.

• Make sure the anti-tip device is properly installed on the range. See the installation instructions for more information.

• Due to the size and weight of the range, have two or more people move the range.

• Remove all tape and packaging materials.

• Remove all accessories from the cooktop, oven, and/or lower drawer. Grates are heavy. Use caution when handling them.

• Make sure no parts came loose during shipping. Do not install in an area exposed to dripping water or outside weather conditions. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 8 2019-02-27 2:26:13English 9 Important safety information Cooktop safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Make sure all burners are off when you are not using them.

• Do not use aluminium foil to line the grates or any part of the cooktop.

• Do not leave burners unattended on medium or high heat settings.

• Before igniting the burners make sure all burner caps are properly in place and all burners are level.

• Always use the Lite position when igniting the burners and make sure the burners have ignited. If ignition fails, turn the knob to OFF and wait until the gas has dissipated.

• When you set a burner to simmer, do not turn the knob quickly. Make sure the ame stays on.

• Do not place any objects other than cookware on the cooktop.

• This cooktop is designed for use with a wok or wok ring attachment.

• To ame food, you must have a ventilation hood. When you ame food, the hood must be on.

• Before removing or changing cookware, turn off the burners.

• Remove food and cookware immediately after cooking.

• Before removing any parts of the burner for cleaning, make sure the range is off and completely cool.

• After cleaning the burner spreader, make sure it is completely dry before re- assembling.

• Make sure the spark mark on the dual burner spreader is placed beside the electrode when it is assembled.

• To avoid carbon monoxide poisoning, do not pour water into the cooktop well while cleaning.

• Select a level, well-constructed oor that can support the range’s weight. Synthetic ooring, such as linoleum, must withstand 180 °F (82 °C) temperatures without shrinking, warping, or discoloring. Do not install the range directly over interior kitchen carpeting unless a sheet of ¼ inch plywood or a similar insulator is placed between the range and carpeting. Select a location where a grounded, 3- prong outlet is easily accessible.

• If the range is located near a window, do not hang long curtains or paper blinds on that window.

• For the range to ventilate properly, make sure the range’s vents are not blocked or covered, and that there is enough clearance at the top, back, sides, and underneath the range. The vents allow the necessary exhaust for the range to operate properly with correct combustion and get the good cooking result.

• Make sure the wall coverings around the range can withstand heat up to 200 °F (93 °C) generated by the range.

• Cabinet storage above the surface of the range should be avoided. If cabinet storage above the range is necessary: allow a minimum clearance of 40 inches (102 cm) between the cooking surface and the bottom of the cabinet or install a range hood that projects horizontally a minimum of 5 inches (12.7 cm) beyond the bottom of the cabinets.

• Locate the range out of kitchen trafc paths and drafty locations to prevent poor air circulation.

• If the range is located near a window, NEVER hang long curtains or paper blinds on that window. They could blow over the surface burners and ignite, causing a re hazard. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 9 2019-02-27 2:26:1310 English Important safety information Important safety information

• Place pots in the center of the grate. Do not place a pot larger than 9" in diameter on the left rear burner. If you place an oversized pot in the wrong position, it might disrupt necessary air circulation and make the ame on the burner sputter and burn inefciently.

• To warm liquids such as sauces, stir them while warming.

• Do not wear loose or hanging garments when using the range. They could ignite and burn you if they touch a surface burner.

• Never leave plastic items on the cooktop. Hot air from the vent can melt or ignite plastic items or cause build up of dangerous pressure in closed plastic containers. You may get severe burns if you touch the surfaces near the vent while the oven is operating.

• Do not place portable appliances, or any other object other than cookware on the cooktop. Damage or re could occur if the cooktop is hot.

• Always make sure foods being fried are thawed and dried. Moisture of any kind can cause hot fat to bubble up and over the sides of the pan.

• Always make sure the controls are OFF and the grates are cool before you remove them to prevent any possibility of burning.

• Do not put any combustible material or items around the range.

• Take care that your hands do not touch the burners when they are on. Turn off the burners when you change a pan or pot.

• Select cookware that is designed for top-range cooking. Use cookware that is large enough to cover the burner grates. Adjust the burner ames so that the ames do not extend beyond the bottom of the cookware.

• To avoid cookware discoloration, deformity, and/or carbon monoxide poisoning, do not use cookware that is substantially larger than the grate.

• Make sure cookware handles are turned to the side or rear of the cooktop, but not over other surface burners.

• Stand away from the range while frying.

• Always heat frying oils slowly, and watch as they heat. If you are frying foods at high heat, carefully watch during the cooking process. If a combination of fats or oils is to be used during frying, mix them together before heating.

• Use a deep-fryer thermometer whenever possible. This prevents overheating the fryer beyond the smoking point.

• Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid cooking unthawed food or food with excessive amounts of ice.

• Before moving cookware full of fats or oils, make sure it has completely cooled.

• To prevent delayed eruptive boiling, always allow heated liquids to stand at least 20 seconds after you have turned off the burner so that the temperature in the liquid can stabilize. In the event of scalding, follow these rst aid instructions: a. Immerse the scalded area in cool or lukewarm water for at least 10 minutes. b. Do not apply any creams, oils, or lotions. c. Cover with a clean, dry cloth. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 10 2019-02-27 2:26:13English 11 Important safety information Self-cleaning oven safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• The self-cleaning feature operates the oven at temperatures high enough to burn away food soils in the oven. The range is extremely hot during a self-cleaning cycle. Do not touch any surfaces of the range during a self- cleaning cycle.

• Keep children away from the oven during a self-cleaning cycle.

• Before starting a self-cleaning cycle, remove all racks, cookware, and utensils from the oven. Only porcelain-coated oven racks may be left in the oven.

• Before starting a self-cleaning cycle, wipe grease and food soils from the oven.

• When opening the door after a self-cleaning cycle, stand away from the oven.

• If the self-cleaning cycle malfunctions, turn off the oven, disconnect the power supply, and contact a qualied service technician. Oven safety WARNING To reduce the risk of re, electric shock, personal injuries, and/or death, observe the following precautions.

• Do not use the oven for non-cooking purposes such as drying clothes or storage. Use the oven for cooking only.

• Make sure the inner portion of the split oven-rack is in the proper position within the outer rack.

• Make sure the oven racks are placed on the same level on each side.

• Do not damage, move, or clean the door gasket.

• Do not spray water on the oven glass while the oven is on or just after you have turned it off.

• Do not use aluminium foil or foil liners anywhere in the oven. Do not use aluminium foil or like material to cover any holes or passages in the oven bottom or to cover an oven rack.

• Stand away from the oven when opening the oven door.

• Keep the oven free from grease buildup.

• When repositioning the oven racks, make sure the oven is completely cool.

• Only use cookware that is recommended for use in gas ovens.

• To avoid damaging the burner control knobs, always bake and/or broil with the oven door closed.

• Do not broil meat too close to the burner ame. Trim excess fat from meat before cooking.

• When using cooking or roasting bags in the oven, follow the manufacturer’s directions.

• Do not touch any surfaces of the range during oven cooking. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 11 2019-02-27 2:26:1412 English Overview Overview Layout

• Surface burner grates (2) * Surface burners and caps (4)

• Flat rack (2) * Wok grate (1)

• Gliding rack (1) * Front leg cover (2) NOTE If you need an accessory marked with a *, you can buy it from the Samsung Contact Center (1-800-726-7864). NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 12 2019-02-27 2:26:14English 13 Before you start Before you start You should know about the following features and components before you use your range for the rst time. Oven vent/Cooling vent Cooling vent Oven vent Both the oven vent and the cooling vent are located at the back of the oven range. Proper air circulation prevents combustion problems and ensures good performance.

• Do not block the vent or its surroundings with objects.

• Use caution when placing items near the vent. Hot steam can cause them to overheat or melt. Bottom of oven vent cover

• Make sure that the oven vent cover sits securely on the cooktop. You can verify that the oven vent cover is in the correct position by conrming that the tabs on the bottom side of the oven vent cover t into the corresponding slots on the cooktop. Mode selector knob

The Modes are printed on the knob itself. To select a mode, turn the knob so that the mode you want is aligned with the line on the knob frame. See Baking and Roasting on page 17 for an example. 01 OFF: Cancel the current operation. 02 Bake: Bake food evenly using the lower oven burner. 03 Broil: Broil food using the upper oven burner only. 04 Roast: Roast meat evenly using the lower oven burner.

Convection Bake: Activates convection baking for large amounts of food on multiple racks. 06 Convection Roast: Activates convection roasting for large cuts of meat. 07 Dehydrate: Activates the Dehydrate function. 08 Keep Warm: Keep cooked food warm at a lower temperature of 170 °F (77 °C). 09 Proof: Activates the Bread proof function. 10 Clean: Burn off food residues at very high temperatures. Important: To set the oven temperature in most modes, you must turn the separate temperature selector knob to the temperature you want. NOTE The temperature selector knob turns freely. Pushing the knob in is not necessary to turn it. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 13 2019-02-27 2:26:1514 English Gas range Gas rangeGas range Step 1 Put all ingredients into a cooking container (pan, pot, etc.). Step 2 Place the container on a surface burner. Step 3 Ignite the surface burner. Cookware Requirements

• Flat bottom and straight sides

• Well-balanced with the handle weighing less than the main portion of the pot or pan. Material characteristics

• Aluminum: An excellent heat conductor. Some types of food may cause the aluminum to darken. However, anodized aluminum cookware resists staining and pitting.

• Copper: An excellent heat conductor but discolors easily.

• Stainless steel: A slow heat conductor with uneven cooking performance but is durable, easy to clean, and resists staining.

• Cast-Iron: A poor conductor but retains heat very well.

• Enamelware: Heating characteristics depend on the base material.

• Glass: A slow heat conductor. Use only glass cookware that is specied for range top cooking or oven use. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 14 2019-02-27 2:26:15English 15 Gas range Wok grate Woks are often used for stir frying, pan frying, deep frying, and poaching. The provided wok grate supports 12" to 14" woks.

1. Turn off all burners, and wait until the

grates completely cool down.

2. Place the wok grate on either side

3. Put a wok on the wok grate. Make sure

the wok settles securely on the work grate.

4. Turn on the burner, and adjust the

ame level as appropriate. CAUTION

• Do not remove the wok grate until the cooktop grates, surfaces, and wok grate completely cool down.

• When using the cooktop or oven, the wok grate on the cooktop may become very hot. Use oven gloves when placing or removing the wok grate.

• Do not use cookware with a at bottom or with a diameter less than the wok ring diameter. The cookware may tip over.

• Do not use an oversized wok. The burner ames may spread out, causing damage nearby.

• Use only the supplied wok grate. This cooktop is not compatible with other manufacturers' wok rings or wok grates.

• This cooktop is not designed to ame food. Gas burners

Each burner has a corresponding knob that enables you to set the ame level from LO to HI. In addition, each burner has a Lite setting. Turning a knob to Lite ignites the corresponding burner. The burner indicators are located above the corresponding knob and show which burner the knob controls. Each burner is designed for specic cooking purposes. Position Purpose Food type Characteristics Right Front (RF) 22,000 BTU Power heating/ Low simmering Boiling food, tomato sauce Maximum output Right Rear (RR) 5,000 BTU Low simmering Chocolate, casseroles, sauces Delicate food that requires low heat for a long time Left Front (LF) 15,000 BTU Quick heating General General-purpose cooking Left Rear (LR) 15,000 BTU Quick heating General General-purpose cooking NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 15 2019-02-27 2:26:1616 English Gas range Gas range Ignition

Make sure all surface burners are properly installed.

1. Push in and turn the control knob to the

Lite position. You will hear a "clicking" sound indicating the electronic ignition system is working properly.

2. After the surface burner lights, turn

the control knob to shift it out of the Lite position and turn off the electronic ignition system.

3. Turn the control knob to adjust the

ame level. Manual ignition You can ignite the burner manually in case of a power failure. Use caution when doing this.

1. Hold a long gas grill lighter to the surface burner you want to light.

2. Push in and turn the control knob for that burner to the Lite position. Turn on

the grill lighter to ignite the burner.

3. After the burner is lit, turn the control knob to adjust the ame level.

Flame level The ames on the burners should always stay under the cookware, and should not extend beyond the cookware bottom at any time. WARNING

• Flames larger than the cookware bottom may result in a re or physical injury.

• When you set a burner to simmer, do not turn the burner knob quickly. Watch the ame to make sure it stays on.

• After turning on a surface burner, check to make sure that the burner has ignited. Adjust the level of the ame by turning the burner knob.

• Always turn off the surface burner controls before removing cookware. All surface burner controls should be turned OFF when you are not cooking.

• Always turn the burners off before you go to sleep or go out.

• If you smell gas, turn off the gas to the range and call a qualied service technician. NEVER use an open ame to locate a leak. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 16 2019-02-27 2:26:16English 17 Gas oven Gas oven Step 1 Put all ingredients in a heat-safe container. Step 2 Select a cooking mode and temperature, and then start preheating. Step 3 Place the container on a rack. Step 4 Close the door and start cooking. Cooking mode

• Make sure to close the door before you start cooking.

• If you leave the door open for 30 seconds while the oven is in convection baking/roasting, baking, roasting, or broiling modes, the oven burner shuts off. To restart the burner, close the door. Baking and roasting

1. Turn the mode selector knob from OFF

to Bake, Roast, Convection Bake or Convection Roast.

2. Rotate the temperature selector knob

to set the temperature from the OFF position. You can set the oven to any temperature from LO to 550 °F.

• The gas oven preheats and the preheating LED turns on and then stays on until the oven reaches the temperature you set.

• When preheating is complete, place the food in the gas oven, and then close the door.

3. When cooking is complete, rotate both

the mode and temperature selector knobs to the OFF position, and then take out the food. NOTE To change the temperature during cooking, use the temperature selector knob. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 17 2019-02-27 2:26:1718 English Gas oven Gas oven Convection cooking The convection fan at the back of the gas oven circulates hot air evenly throughout the oven cavity so that food is evenly cooked and browned in less time than with regular heat. Convection baking

• Ideal for foods being cooked using multiple racks.

• Good for large quantities of food.

• Provides the best performance for cookies, biscuits, brownies, cupcakes, cream puffs, sweet rolls, angel food cake, and bread.

• Cookies bake best when cooked on at cookie sheets.

• When convection baking using a single rack, place the rack in rack position 3 or 4.

• When convection baking using multiple racks, place the racks in positions 3 and 5 (for cake) or 2 and 5 (for cookies).

• The oven automatically adjusts the temperature for convection baking. Convection roasting

• Good for larger, tender cuts of meat, uncovered.

• For best performance, place a broiler pan and grid under the meat or poultry. The pan catches grease spills and the grid prevents grease spatters.

• Heated air circulates over, under, and around the food. Meat and poultry are browned on all sides as if they were cooked on a rotisserie. Limitations Feature Minimum Maximum Bake LO 550 °F (288 °C) Broil LO HI Roast LO 550 °F (288 °C) Clean - 3 hours Convection Bake LO 550 °F (288 °C) Convection Roast LO 550 °F (288 °C) Keep Warm - 3 hours NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 18 2019-02-27 2:26:17English 19 Gas oven Recipe guide Broiling guide NOTE

• This is for reference only.

• Preheating for 5 minutes before broiling is recommended.

• The size, weight, thickness, starting temperature, and your doneness preference will affect broiling times.

• This guide is based on meats at refrigerator temperature.

• If you have covered the meat with aluminum foil and you let it stand covered for 10 minutes after cooking is complete, the internal temperature increases by 5-10 °F degrees. Food Doneness Size Thickness Broil setting Rack position Cooking time 1st side 2nd side Hamburgers Medium 9 patties 1" HI 6 5:00 4:00 Beef steak Medium - 1" HI 5 7:00- 8:00 4:00- 6:00 Medium - 1½" HI 5 12:00- 16:00 11:00- 14:00 Chicken pieces Well done 2-2½ lbs. ¾"-1" HI 3 18:00- 20:00 12:00- 15:00 Chicken breasts Well done 2-3 pcs - HI 4 15:00- 20:00 7:00- 12:00 Pork chops Well done 1 lb. ½" HI 5 9:00- 11:00 6:00- 9:00 Lamb chops Medium 10 oz. 1½" HI 4 8:00- 12:00 5:00- 8:00 Well done 10 oz. 1½" HI 4 10:00- 16:00 7:00- 11:00 Broiling Broiling uses the oven broil burner at the top of the oven to cook and brown food. Meat or sh must be put on a broiling grid in a broiling pan. Preheating for 5 minutes before broiling is recommended.

2. Rotate the mode selector knob from

OFF to the Broil position, and then turn the temperature selector knob to set the broiling temperature from OFF to HI or LO.

3. Let the oven pre-heat for 5 minutes,

and then place the pan with the food on the desired rack. Close the oven door.

4. When one side of the food is browned,

turn it over and start cooking the other side.

5. When broiling on both sides is

complete, turn both knobs to the OFF position. NOTE

• Use the Broil LO for poultry or thick cuts of meat to prevent overbroiling.

• Use caution when you open the oven door to turn over the food. The air escaping from the oven will be very hot.

• This oven is designed for closed door broiling. While broiling, keep the door closed. Only open the door to put food in, turn food over, or take food out. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 19 2019-02-27 2:26:1720 English Gas oven Gas oven Multi-rack Baking

• When baking cakes on two racks, place the racks in positions 3 and 5 for the best performance.

• When baking cookies on two racks, place the oven racks in positions 2 and

• For 4 baking pans on two racks: Place two pans in the rear of the upper rack and the other two in the front of the lower rack.

• When baking multiple items on one rack, maintain a 1" to 1.5" (2.5 cm to

3.8 cm) space between items.

• When using the gliding rack, place it below the at rack. Baking items Rack position Cake 3 and 5 Cookie 2 and 5 Cakes pans position

Cookie sheets position CAUTION Make sure to close the door after turning over the food. Racks Position The gas oven range comes with 3 racks in 7 different positions. Each rack guide has a stop that prevents you from accidentally pulling the rack out completely.

Rack position Food type 6 Hamburgers and steaks 6 or 5 Toast 4 or 3 Biscuits, mufns, brownies, cookies 3 Bundt or pound cakes 2 Angel food cake, pies 1 or 2 Roasts (small or large), ham, turkeys CAUTION

• Do not cover an oven rack with aluminum foil. This will disturb the heat circulation, resulting in poor baking.

• Do not place aluminum foil on the oven bottom. The aluminum can melt and damage the oven.

• Arrange the oven racks only when the oven is cool.

• When placing an oven rack in the topmost rack position (position 7), make sure the rack is situated stably on the embossed stop. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 20 2019-02-27 2:26:18English 21 Gas oven Special features Dehydrate Dehydrate dries food or removes moisture from food via heat circulation. After drying the food, keep it in a cool and dry place. For fruit, adding lemon (or pineapple) juice or sprinkling sugar on the fruit helps the fruit retain sweetness.

1. Place the container with the food on a

rack, and then close the door.

2. Set the temperature selector knob to

3. Turn the mode selector knob from OFF

to the Dehydrate position.

4. The oven heats up to 150 °F (66 °C).

NOTE You can cancel Dehydrate at any time by setting the mode selector knob to the OFF position. Inserting and removing an oven rack To insert an oven rack

1. Place the rear end of the rack on a rack

2. Slide the rack into the rack guide while

holding the front end of the rack. To remove an oven rack

1. Pull out the rack until it stops.

2. Pull up the front end of the rack and

remove it from the rack guide. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 21 2019-02-27 2:26:1822 English Gas oven Gas oven Keep Warm Keeps cooked food warm at a low temperature up to 3 hours.

1. Place the container with the food on a

rack, and then close the door.

2. Set the temperature selector knob to

3. Turn the mode selector knob from OFF

to the Keep Warm position.

4. The oven heats up to 170 °F (77 °C).

NOTE You can cancel Keep Warm at any time by setting the mode selector knob to the OFF position. Other features Oven light Turns the oven light on and off. Press the Oven Light switch button to turn the oven light on and off. Bread proof Bread proof provides an optimal temperature for the bread proong process, and therefore does not require a temperature adjustment. For the best results, always start the Bread proof option with a cool oven.

1. Place the container with the dough on a

rack, and then close the door.

2. Set the temperature selector knob to

3. Turn the mode selector knob from OFF

to the Proof position.

4. The oven heats up to 100 °F.

NOTE You can cancel Bread proof at any time by setting the mode selector knob to the OFF position. CAUTION

• Do not use Bread proof when the oven temperature is above 100 °F. If the temperature is above 100 °F, Bread proof will not function. Instead, a warning beep will sound 3 times and the mode and temperature selector knob lights will blink ice blue. Wait until the oven cools down.

• Do not use Bread proof for warming food. The proong temperature is not hot enough to keep food warm.

• Place the dough in a heat-safe container on rack position 3 or 4 and cover it with a cloth or with plastic wrap. The plastic wrap may need to be anchored underneath the container so that the oven does not blow it off the dough.

• To avoid lowering the temperature and extending proong time, do not open the oven door. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 22 2019-02-27 2:26:18English 23 Gas oven NOTE The Wi-Fi Button is underneath the temperature selector knob. If you need to press the Wi-Fi Button, remove the temperature selector knob by grasping it and then pulling it straight back towards you. Smart ConnectPreheating Smart Connect Wi-Fi button Smart Connect LED Temperature selector knob (4

knob) Smart Connect Using the smart connect feature Your range has a built-in Wi-Fi module that you can use to sync the range with the SmartThings app. Using the SmartThings app, you can:

• Monitor the operational status of your range or the notications from your range, and then change options or settings if necessary. Functions that can be operated from the SmartThings app may not work smoothly if communication conditions are poor or the product is installed in a place with a weak Wi-Fi signal. How to connect the range Before you can use the remote features of your Samsung oven or range, you must pair it to the SmartThings app.

1. Download and open the SmartThings app on your smart device.

2. Follow the app's on-screen instructions.

3. Pull off and remove the temperature selector (4th) knob to expose the Wi-Fi

4. Press the Wi-Fi button for 3 seconds to connect your range.

5. Once the process is complete, the Smart Connect LED indicator stops

blinking and glows steadily. The range is connected successfully. Replace the temperature selector knob.

6. If the Smart Connect LED indicator does not stop blinking and glow steadily,

follow the instruction in the app to reconnect. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 23 2019-02-27 2:26:1924 English Gas oven Gas oven Using the hood control feature NOTE This product features a Bluetooth device that you can use to connect the range to Samsung hood control models. Through the Bluetooth connection, you can use the hood control function on the SmartThings app. For the matching hood control-enabled range and hood, refer to the below table. Gas oven range Hood Model NX58M9960P* NK30K7000W* To connect to a hood control model and a hood:

1. Download and run the SmartThings app on your smartphone. Then, complete

the Smart Connect procedure to connect to the range. See page 23.

2. Follow the Bluetooth instructions of the hood control model and activate the

Bluetooth connection.

3. Press the Bluetooth icon

on the hood control panel. The Bluetooth icon LED blinks.

4. Pull off and remove the mode selector (3

5. When Bluetooth pairing is nished, the Bluetooth icon LED stops blinking and

glows steadily. Replace the mode selector knob.

6. Follow the instructions in the user manual of the hood control model and the

App guide to use the hood control. To monitor the range remotely

1. Make sure the Smart Connect LED indicator has turned on. If the Smart

Connect LED indicator does not turn on, press the Wi-Fi button. (See page 23.) The range can now be monitored remotely with a connected remote device.

2. Select the range icon on the SmartThings app to open the range monitor app.

Smart connect on/off If you set the Smart Connect to Off, mobile devices cannot connect to the range. To turn Smart Connect on, follow these steps:

1. Pull the temperature selector knob straight back towards you to remove it.

2. Press the Wi-Fi button. (See page 23.)

NOTE The Smart Connect LED indicator is on when Smart Connect is enable. The Smart Connect LED indicator is off when Smart Connect is not enabled.

• The range continues operating even if the Wi-Fi connection is lost.

• The SmartThings Application will not work properly if the Wi-Fi Connection is unstable.

• See the SmartThings app manual for detailed information.

• For further instructions, refer to the SmartThings app web manual at www. samsung.com NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 24 2019-02-27 2:26:19English 25 Gas oven Bluetooth on/off

1. Press the Bluetooth icon

on the hood control panel. NOTE

• The Bluetooth icon LED on the hood is on when Bluetooth is enabled. The Bluetooth icon LED on the hood is off when Bluetooth is not enabled.

• If the Smart Connect connection is not successful, you cannot use the SmartThings app to monitor and control the hood.

• Without a Smart Connect connection to the range, you can use a Bluetooth connection to pair the range with the hood and sync them. To do this, follow the Bluetooth connection steps on page 24.

• Bluetooth will not work properly if the Bluetooth connection is unstable.

• See the SmartThings app manual for detailed information. NOTE The Bluetooth button is underneath the mode selector knob. If you need to press the Bluetooth button, remove the mode selector knob by grasping it and then pulling it straight back towards you. Smart ConnectPreheating Bluetooth button Temperature selector knob (3

1. Remove any spills, spots, and grease stains using a soft, wet cloth.

2. Apply an approved stainless steel cleanser to a cloth or paper towel.

3. Clean one small area at a time, rubbing with the grain of the stainless steel if

4. When done, dry the surface using a soft, dry cloth.

5. Repeat steps 2 through 4 as many times as necessary.

• Do not use a steel-wool pad or abrasive cleanser on stainless steel surfaces. It will scratch the surface.

• Do not spray any type of cleanser into the manifold holes. The ignition system is located in those holes and must be kept free of moisture. Racks To keep the racks clean, remove them from the cavity, and soak them in lukewarm soapy water. Then, scour impurities off of the racks using a plastic scouring pad. If the racks do not slide in and out smoothly after you have cleaned them, rub the side rail guides with wax paper or a cloth containing a few drops of cooking oil. This will help the racks glide more easily on their tracks. Gliding rack

1. Remove the gliding rack from the oven.

2. Fully extend the gliding rack on a table.

It is a good idea to put newspaper beneath the rack for later cleanup.

3. If the sliding tracks are contaminated,

remove impurities using a paper towel. Reapply the graphite lubricant according to the instructions on the right. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 26 2019-02-27 2:26:19English 27 Maintenance To apply the graphite lubricant

1. Shake the graphite lubricant before

2. Apply 4 drops of lubricant to the

inner side of the left sliding track, and 4 drops to the outer side of the left sliding track.

4. Extend and collapse the gliding rack

several times to distribute the lubricant. NOTE

• Do not use a dishwasher to clean the racks.

• If a rack does not slide in and out smoothly, apply a few drops of cooking oil to the oven rack guides.

• If a rack becomes too difcult to slide in or out, lubricate the rack.

• To purchase the graphite lubricant, contact us at 1-800-SAMSUNG (726-7864).

• For online shopping, visit http://www.samsungparts.com/Default.aspx and search for part DG81-01629A. CAUTION

• Do not leave racks in the oven during the self-cleaning cycle. The extreme heat generated in this cycle can permanently peel off the racks' coating and make it difcult to remove the racks.

• Do not spray cooking oil or lubricant directly onto the gliding rack. Door Do not remove the inner gasket of the oven door for cleaning. Inner side

• Inner surface: Clean the inner side of the door manually using a soapy plastic scouring pad, and then wipe with a dry cloth. Take care not to get the gasket wet or allow moisture into the door.

• Inner glass: The inner glass is cleaned automatically during the self-cleaning cycle. Outer side

• Outer surface: Follow the cleaning instructions for the stainless steel surface in the previous section.

• Outer glass: Clean the outer glass using a glass cleanser or soapy water. Rinse and dry thoroughly. Take care not to get the gasket wet or allow moisture into the door.

CAUTION Do not let moisture enter the door or contact the door gasket (*). Moisture may reduce the gasket’s performance. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 27 2019-02-27 2:26:2028 English Maintenance Maintenance Surface burners Burner controls Make sure all surface burner knobs are in the OFF position.

1. Pull the knobs off the control valve

2. Clean the knobs in warm, soapy water.

Then, rinse and dry them thoroughly.

3. Clean the stainless steel surfaces using

stainless steel cleaner.

4. Push the knobs back onto the control

valve stems. CAUTION

• Do not clean the control knobs in a dish washer.

• Do not spray cleansers directly onto the control panel. Moisture entering the electric circuits may cause electric shock or product damage. Cooktop surface The porcelain-enameled cooktop surface needs to be kept clean. We recommend that you remove food spills immediately after they take place.

1. Turn off all surface burners.

2. Wait until all burner grates cool down,

and then remove them.

3. Clean the cooktop surface using a soft

cloth. If food spills run into gaps of the burner components, remove the burner cap and the head, and wipe out the spills.

4. When cleaning is nished, reinsert the

burner components, and put the burner grates into position. CAUTION

• Do not use a steel-wool pad or abrasive cleaner, which can scratch or damage the enamel surface.

• Do not remove the cooktop surface for cleaning purposes. The gas lines leading to the burner manifolds can be damaged, resulting in a re or system failure.

• Do not pour water into the cooktop well while cleaning the cooktop. This could leak down into the range gas and electrical systems creating a risk of electrical shock or high levels of Carbon Monoxide, due to corrosion of the gas valves or ports.

• Keep oven vent ducts unobstructed. Clean vents frequently to avoid grease buildup. There can be slight popping sound during oven cooking. This sound may occur during the normal oven burner cycling, when the oven burner ame is extinguished. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 28 2019-02-27 2:26:20English 29 Maintenance Burner grates and components Turn off all surface burners and make sure they have all cooled down.

2. Remove the burner caps from the

3. Remove the burner heads from the

valve manifolds to reveal the starter electrodes.

4. Clean all removable grates and burner

components in warm, soapy water. Do not use steel-wool pads or abrasive cleaners.

5. Rinse and dry grates and burner

components thoroughly.

6. Return the burner heads to their

positions on top of the manifold valves. Make sure a starter electrode is inserted through the hole in each burner head.

7. Return the burner caps to their

positions on top of burner heads. To ensure proper and safe operation, make sure the burner caps lie at on top of the burner heads.

8. Reinstall the burner gates in their

respective positions.

9. Turn on each burner and check if it

operates properly. After verifying that a burner operates normally, turn it off. NOTE The precise simmer burner (RR) cap and the inner dual burner (RF) cap are interchangeable. Top Bottom CAUTION

• The starter electrodes are not removable. Do not attempt to remove them by force.

• Make sure all burner components (heads and caps) are reinstalled properly. They are stable and rest at when installed properly.

• To avoid chipping, do not bang grates and caps against each other or hard surfaces such as cast iron cookware.

• The burner spreader can be blocked by food or dust. Clean the spreader if it appears blocked. If you clean the spreader with water, assemble it only after it is completely dry. If the spreader is wet, it might prevent the burners from igniting. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 29 2019-02-27 2:26:2130 English Maintenance Maintenance Self-cleaning This self-cleaning oven uses high temperatures (well above cooking temperatures) to burn off leftover grease and residue completely or reduce them to a nely powdered ash that you can wipe away with a damp cloth. CAUTION

• Do not leave small children unattended near the gas oven during the self- cleaning cycle. The outside surfaces of the gas oven can get extremely hot.

• Some birds are extremely sensitive to fumes from a self-cleaning gas oven. Relocate birds to a well-ventilated room away from the gas oven.

• Do not line the oven, oven racks, or oven bottom with aluminum foil. Doing so will result in poor heat distribution, produce poor baking results, and cause permanent damage to the oven interior. The aluminum foil will melt onto and adhere to the interior oven surfaces.

• Do not force the oven door open during the self-cleaning cycle. This will damage the automatic door-locking system. The door automatically locks when the self-cleaning cycle is started and stays locked until the cycle is completed or cancelled and the oven temperature is below 400 °F.

• Use caution when opening the oven door after the self-cleaning cycle. The gas oven will still be VERY HOT and hot air and steam might escape when the door is open.

• Wipe off any excess spillage before using the self-cleaning operation.

• Do not use oven cleaners. Commercial oven cleaners or oven liners should NEVER be used in or around any part of the oven. Residue from oven cleaners will damage the inside of the oven during a self-cleaning operation.

• Both knobs must be initially turned from the OFF position. To perform the self-cleaning cycle Make sure the door lock is released. Remove all racks from the oven cavity.

1. Make sure the oven door is unlocked

and closed completely.

2. Turn the mode selector knob from OFF

to the Clean position.

3. Turn the temperature selector knob

from OFF to the Clean position.

4. The oven door is locked and the oven

begins to heat up. When the cycle is complete, an alert beep sounds. The door will remain locked until the oven temperature falls below 400 °F (205 °C).

5. Turn both the mode and temperature

selector knobs to the OFF position. Mode Selector Knob Temperature Selector Knob CAUTION Do not use the surface burners while the gas oven is performing a self-cleaning cycle. If you attempt to start a self-cleaning cycle while using the surface burners, an alert beep sounds and the mode and temperature selector knob lights blink ice blue 5 times. If you attempt to use the surface burners during a self-cleaning cycle, a warning beep sounds 3 times and the knob lights blink ice blue for 10 seconds. The self-cleaning cycle will be cancelled. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 30 2019-02-27 2:26:21English 31 Maintenance To cancel the self-cleaning cycle You may nd it necessary to stop or interrupt a self-cleaning cycle due to smoke in the oven. To turn off the self-cleaning cycle, turn both the mode and temperature selector knobs to the OFF position. The cycle turns off, but the door remains locked until the oven temperature falls below 400 °F (205 °C). After self-cleaning

• The door stays locked until the internal oven temperature falls below 400 °F.

• When the oven has cooled down, wipe the oven surfaces with a cloth to remove ash residue.

• Stubborn stains can be removed using a steel-wool pad. Lime deposits can be removed using a vinegar-soaking cloth.

• If you are not satised with the cleaning results, repeat the self-cleaning cycle.

• Self-cleaning does not operate within 2 hours after running the self-cleaning cycle. CAUTION Do not attempt to open the oven door immediately after the self-cleaning cycle is complete. The oven is still very hot when the door unlocks. Escaping hot air and/or steam could burn you. Replacing the oven lights Oven lights (2 locations) The oven lights are standard 40-watt appliance bulbs. They come on when you open the oven door. To replace an oven light:

1. Turn off the oven.

2. Make sure the oven and oven light are

3. Open the door, and remove the glass

cover by turning it counterclockwise.

4. Remove the oven light from the socket

by turning it counterclockwise.

5. Insert a new 40-watt appliance bulb

into the socket, and then turn it clockwise to tighten.

6. Reinsert the glass cover, and then turn

it clockwise to tighten. CAUTION To prevent electric shock, make sure the gas oven is turned off and cool before replacing the oven light. NOTE

• The oven lights do not operate during a self-cleaning cycle.

• Remove the racks if they prevent you from accessing an oven light. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 31 2019-02-27 2:26:2232 English Maintenance Maintenance Oven door: remove and re-install Oven door To remove the oven door

1. Turn off the oven.

2. Fully open the oven door.

3. Pull the hinge locks away from the

oven body and down toward the door frame into the unlocked position.

4. Close the door to 5 degrees from

vertical. This is the removal position.

5. While holding both sides of the oven

door tightly, lift it up and out until the hinge arms come clear of the slots at the bottom of the oven door.

6. Place the door in a safe location.

• The door is very heavy. Be careful when removing and lifting the door. Do not lift the door by the handle.

• Take care when moving the oven door. Improper handling could result in physical injury.

• To prevent electric shock, make sure the oven is turned off before removing the oven door. To reinstall the door

1. Firmly grasp both sides of the door at

2. With the door set at the same angle as

the removal position (about 5 degrees from vertical), slide the hinge arms into the hinge slots at the bottom of the door.

3. Open the door fully. If you cannot open

the door fully, the hinge arms are not properly in the hinge slots.

4. Lock the hinge arms by pushing them

up against the front frame of the oven.

5. Close the door, and make sure it opens

and closes normally. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 32 2019-02-27 2:26:23English 33 Troubleshooting Troubleshooting Troubleshooting Samsung works hard to ensure that you don’t have problems with your new electric oven. If you run into unexpected trouble, look rst for a solution in the tables below. If you’re still having trouble after trying the suggested solution, call Samsung at 1-800-SAMSUNG (1-800-726-7864). Gas safety Problem Possible cause Solution You smell gas. The surface burner knob is not in the OFF position and the burner is not lit. Turn the burner knob to OFF. There is a gas leak. Clear the room, building, or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Do not call from your phone. It is electrical and could cause a spark that could ignite the gas. Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the re department. Surface burner Problem Possible cause Solution All burners do not light. The power cord is not plugged into the electrical outlet. Make sure the electrical plug is plugged into a live, properly grounded outlet. A fuse in your home may be blown or the circuit breaker tripped. Replace the fuse or reset the circuit breaker. The gas supply is not properly connected or turned on. See the Installation instructions that came with your range. Surface burners do not light. The control knob is not set properly. Push in the control knob and turn it to the Lite position. The burner caps are not in place. The burner base is misaligned. Clean the electrodes. Put the burner cap on the burner head. Align the burner base. Surface burner clicks during operation. The control knob has been left in the Lite position. After the burner lights, turn the control knob to a desired setting. If the burner still clicks, contact a service technician. The burners do not burn evenly. Surface burner components and caps are not assembled correctly and level. See page 29. Surface burners are dirty. Clean surface burner components. (See page 29.) Very large or yellow surface burner ames. Wrong orice is assembled. Check the burner orice size and contact your installer if you have the wrong orice (LP gas instead of natural gas or natural gas instead of LP gas). NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 33 2019-02-27 2:26:2334 English Troubleshooting Troubleshooting Problem Possible cause Solution Surface burners light but oven burners do not light. The Gas Pressure Regulator shut off switch is in the OFF position. Call a qualied service technician. Oven Problem Possible cause Solution The oven control beeps and the knob LED turns orange. The 7-Segment display, below the RF control (6

knob, shows an information code. You have a function information code. See the Information codes chart on page 36. Rotate both the mode and temperature selector knobs to the OFF position and restart the oven. If the problem persists, disconnect all power to the range for at least 30 seconds and then reconnect the power. If this does not solve the problem, call for service. Very large or yellow oven burner ames. The oven burner air adjustment shutters need to be adjusted. Call for a qualied service technician. The gas supply is not properly connected or turned on. See the Installation instructions that came with your range. Wrong orice is assembled. Check the burner orice size and contact your installer if you have the wrong orice (LP gas instead of natural gas or natural gas instead of LP gas). Oven temperature is too hot or cold. The oven thermostat needs adjustment. Call for a qualied service technician. Problem Possible cause Solution Oven light (lamp) will not turn on. Loose or burned-out bulb. See page 31. The switch button operating the oven light needs to be replaced. Call for a qualied service technician. Oven smokes excessively during broiling. Meat or food not properly prepared before broiling. Cut away excess fat and/or fatty edges that may curl. Improperly positioned top oven rack. See the Broiling guide on page 19. Greasy buildup on oven surfaces. Regular cleaning is necessary when broiling frequently. Oven will not self- clean. The oven is too hot. A warning beep sounds 3 times, and the mode and temperature selector knob lights blink ice blue. Let the oven cool down, and then reset the controls. The self-clean cycle will not lock the oven door if the oven temperature is too hot. The door must lock before the self-clean cycle can start. Self- cleaning does not operate within 2 hours after running the self-cleaning cycle. The self-cleaning oven controls are not properly set. Reset the self-cleaning oven controls. (See page 30.) The door is opened. An alert beep sounds, and the mode and temperature selector knob lights blink ice blue. Make sure that the door is closed. Crackling or popping sound. This is normal. This is the sound of the metal heating and cooling during any cooking or cleaning function. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 34 2019-02-27 2:26:23English 35 Troubleshooting Problem Possible cause Solution Excessive smoking during a self- cleaning cycle. This is the rst time the oven has been cleaned. This is normal. The oven will always smoke more the rst time it is cleaned. Wipe up all excessive soiling before starting the self-cleaning cycle. If smoke persists, rotate both the mode and temperature selector knobs to the OFF position. Open the windows to clear the smoke from the room. After the oven has cooled and unlocked, wipe up excessive soil and reset the oven for self-cleaning. Oven door will not open after a self- cleaning cycle. This is normal. The oven door will stay locked until the oven temperature drops below 400 °F. Oven not clean after a self-cleaning cycle. A ne dust or ash is normal. This can be wiped clean with a damp cloth. Set the self-cleaning cycle for a longer cleaning time. The cycle was not long enough to burn off the dirt buildup. Extremely dirty ovens require hand- cleaning of excessive spillovers and food buildup before you start a self-cleaning cycle. Multiple self-cleaning cycles may be necessary to completely clean the oven. Steam or smoke coming from under the control panel. This is normal. The oven vent is located there. More steam is visible when using the convection functions or when baking or roasting multiple items at the same time. Burning or oily odor coming from the vent. This is normal for a new oven and will disappear within 1/2 hour of the rst Bake cycle. To speed the process, set a self-cleaning cycle for 3 hours. (See page 30.) Problem Possible cause Solution Strong odor. This is temporary. The insulation around the inside of the oven emits an odor the rst few times the oven is used. Oven racks are difcult to slide.

Apply a small amount of vegetable oil to a paper towel and wipe edges of the oven racks with the paper towel. Racks become dull and hard to slide if they are left in the oven during a self-clean cycle. Fan noise. This is normal. The convection fan runs until the function is over or the door is opened. Convection fan is not working.

The fan starts automatically when the oven reaches the preheat temperature. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 35 2019-02-27 2:26:2336 English Troubleshooting Troubleshooting Others Problem Possible cause Solution The product is not level. The appliance has been installed improperly. The leveling leg(s) is (are) damaged or uneven. Make sure the oor is level, strong, and stable. If the oor sags or slopes, contact a carpenter. Check and level the range. (See the Installation instructions.) The kitchen cabinets are not properly aligned and make the range appear to be not level. Ensure that cabinets are square and provide sufcient room for installation. Food does not bake or roast properly in the oven. Wrong cooking mode is selected. See page 17. The oven racks have not been positioned properly for the food being cooked. See page 20. The cookware has not been positioned correctly on the rack. See page 21. Oven thermostat needs adjustment. Call for a qualied service technician. There is aluminum foil on racks and/or oven bottom. Remove the foil. Food does not broil properly in the oven. Oven controls not set properly. See page 19. Oven door was not closed during broiling. See page 17. The rack has not been properly positioned. See broiling guide on page 19. Information codes OVEN Displayed Code Possible cause Solution C-d0 This code occurs if the control key is short for 1 minute. Clean the buttons and make sure there is no water on/around them. Turn off the oven and try again. If the problem continues, contact a local Samsung service center. C-d1 This code occurs if the door lock is mispositioned. Turn both the mode and temperature selector knobs to OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power. If this does not solve the problem, call for service. C-F0 This code occurs if communication between the Main and Sub PBA is interrupted. C-20 The oven sensor is open when the oven is operating. The oven sensor is short when the oven is operating. C-21 This code occurs if the internal temperature rises abnormally high. Call for service. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 36 2019-02-27 2:26:23English 37 Warranty Displayed Code Possible cause Solution C-30 The PCB sensor is open when the oven is operating. Turn both the mode and temperature selector knobs to OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power. If this does not solve the problem, call for service. The PCB sensor is short when the oven is operating. C-31 This code occurs if the PCB temperature rises abnormally high. Call for service Warranty (U.S.A) PLEASE DO NOT DISCARD.

LIMITED WARRANTY TO ORIGINAL PURCHASER WITH PROOF OF PURCHASE This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials or workmanship for the limited warranty period, starting from the date of original purchase, of: Two (2) Years Parts and Labor This limited warranty is valid only on products purchased and used in the United States that have been installed, operated, and maintained according to the instructions attached to or furnished with the product. To receive warranty service, the purchaser must contact SAMSUNG at the address or phone number provided below for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center to receive warranty service. SAMSUNG will provide in-home service within the contiguous United States during the warranty period at no charge, subject to availability of SAMSUNG authorized servicers within the customer’s geographic area. If in-home service is not available, SAMSUNG may elect, at its option, to provide transportation of the product to and from an authorized service center. If the product is located in an area where service by a SAMSUNG authorized servicer is not available, you may be responsible for a trip charge or required to bring the product to a SAMSUNG authorized service center for service. To receive in-home service, product must be unobstructed and accessible to the service agent. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 37 2019-02-27 2:26:2338 English Warranty Warranty

EXCLUSION OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specic rights, and you may also have other rights, which vary from state to state.

LIMITATION OF REMEDIES

YOUR SOLE AND EXCLUSIVE REMEDY IS PRODUCT REPAIR, PRODUCT REPLACEMENT, OR REFUND OF THE PURCHASE PRICE AT SAMSUNG’S OPTION, AS PROVIDED IN THIS LIMITED WARRANTY. SAMSUNG SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TIME WAY FROM WORK, HOTELS AND/OR RESTAURANT MEALS, REMODELING EXPENSES, LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic rights, and you may also have other rights, which vary from state to state. SAMSUNG does not warrant uninterrupted or error-free operation of the product. No warranty or guarantee given by any other person, rm, or corporation with respect to this product shall be binding on SAMSUNG. To obtain warranty service, please contact SAMSUNG at: Samsung Electronics America, Inc. 85 Challenger Road Ridgeeld Park, NJ 07660 1-800-SAMSUNG (726-7864) and www.samsung.com/us/support Registration Please register your product online at www.samsung.com/register. Questions For questions about features, operation/performance, parts, accessories, or service, call 1-800-SAMSUNG (726-7864), or visit our Web site at www.samsung.com/us/support. Model # Serial # Please attach your receipt (or a copy) to this manual. You may need it, along with your model and serial number, when calling for assistance. During the applicable warranty period, a product will be repaired, replaced, or the purchase price refunded, at the sole option of SAMSUNG. SAMSUNG may use new or reconditioned parts in repairing a product, or replace the product with a new or reconditioned product. Replacement parts and products are warranted for the remaining portion of the original product’s warranty or ninety (90) days, whichever is longer. All replaced parts and products are the property of SAMSUNG and you must return them to SAMSUNG. This limited warranty covers manufacturing defects in materials or workmanship encountered in normal household, noncommercial use of this product and shall not cover the following: damage that occurs in shipment, delivery, installation, and uses for which this product was not intended; damage caused by unauthorized modication or alteration of the product; product where the original factory serial numbers have been removed, defaced, changed in any way, or cannot be readily determined; cosmetic damage including scratches, dents, chips, and other damage to the product’s nishes; damage caused by abuse, misuse, pest infestations, accident, re, oods, or other acts of nature or God; damage caused by use of equipment, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG; damage caused by incorrect electrical line current, voltage, uctuations and surges; damage caused by failure to operate and maintain the product according to instructions; in-home instruction on how to use your product; and service to correct installation not in accordance with electrical or plumbing codes or correction of household electrical or plumbing (i.e., house wiring, fuses, or water inlet hoses). In addition, damage to the glass cooktop caused by (i) use of cleaners other than the recommended cleaners and pads or (ii) hardened spills of sugary materials or melted plastic that are not cleaned according to the directions in the use and care guide are not covered by this limited warranty. The cost of repair or replacement under these excluded circumstances shall be the customer’s responsibility. Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 38 2019-02-27 2:26:23English 39 Warranty This limited warranty shall not cover cases of incorrect electric current, voltage or supply, light bulbs, house fuses, house wiring, cost of a service call for instructions, or xing installation errors. Furthermore, damage to the cooktop caused by the use of cleaners other than the recommended cleaners and pads and damage to the cooktop caused by hardened spills of sugary materials or melted plastic that are not cleaned according to the directions in the use and care guide are not covered. SAMSUNG does not warrant uninterrupted or error-free operation of the product. EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES OR CONDITIONS ON THIS PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL WARRANTIES AND CONDITIONS INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, INFRINGEMENT, OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER GENERAL, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE, AND STATES YOUR EXCLUSIVE REMEDY. Some states or provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state or province to province. To obtain warranty service, please contact SAMSUNG at: Warranty (CANADA) PLEASE DO NOT DISCARD.

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of: One (1) Year Parts and Labor This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the Canada. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG-authorized service center, and any unauthorized service will void this warranty. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. Samsung will provide in- home service during the one (1) year warranty period at no charge subject to availability within the contiguous Canada. In-home service is not available in all areas. To receive in-home service, product must be unobstructed and accessible to the service agent. If service is not available, Samsung may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specied above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 39 2019-02-27 2:26:2440 English Appendix Appendix Samsung Electronics Canada Inc. 2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada 1-800-SAMSUNG (726-7864) and www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) Registration Please register your product online at www.samsung.com/register. Questions For questions about features, operation/performance, parts, accessories, or service, call 1-800-SAMSUNG (726-7864), or visit our Web site at www.samsung.com/ca/ support (English), www.samsung.com/ca_fr/support (French). Model # Serial # Please attach your receipt (or a copy) to this manual. You may need it, along with your model and serial number, when calling for assistance. Warranty Appendix Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@ samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required. The following URL http://opensource.samsung.com/opensource/SimpleConnectTP/ seq/0 leads to the download page of the source code made available and open source license information as related to this product. This offer is valid to anyone in receipt of this information. NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 40 2019-02-27 2:26:24Memo NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 41 2019-02-27 2:26:24Memo NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 42 2019-02-27 2:26:24Memo NX9000K_CHEF_NX58M9960PS_AA_DG68-01008A-06_EN.indd 43 2019-02-27 2:26:24Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or maintenance. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A Consumer Electronics 1-800-SAMSUNG (726-7864) www.samsung.com/us/support CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) DG68-01008A-0

Scan the QR code* or visit www.samsung.com/spsn to view our helpful How-to Videos and Live Shows