HW80BP16636 - Washing machine HAIER - Free user manual and instructions

USER MANUAL HW80BP16636 HAIER

Legend Warning – Important Safety information General information and tips Environmental information Disposal Help protect the environment and human health. Put the packaging in applicable containers to recycle it. Help to recycle waste of electrical and electronic ap- pliances. Do not dispose appliances marked with this symbol with the household waste. Return the product to your local recycling facility or contact your municipal offi ce. Thank you for purchasing a Haier Product. Please read these instructions carefully before using this appliance. The instructions con- tain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance. If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass this manual so that the new owner can become familiar with the appliance and safety warnings. WARNING! Risk of injury or suff ocation! Disconnect the appliance from the mains supply. Cut off the mains cable and dispose of it. Remove the door catch to prevent children and pets to get closed in the appliance.GB

Before switching on the appliance for the fi rst time read the follow- ing safety hints!: WARNING! Before fi rst use ▶ Make sure there is no transport damage. ▶ Make sure all transport bolts are removed. ▶ Remove all packaging and keep out of children´s reach. ▶ Handle the appliance always with at least two persons because it is heavy. Daily use ▶ This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental ca- pabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. ▶ Keep away children under 3 years of age from the appliance un- less they are constantly supervised. ▶ Children shall not play with the appliance. ▶ Do not let children or pets come close to the appliance when the door is open. ▶ Store washing agents out of reach of children. ▶ Pull up zips, fi x loose threads and take care for small items to prevent laundry from being entangled. If necessary, use an ap- propriate bag or net. ▶ Do not touch or use the appliance when barefoot or with wet or damp hands or feet. ▶ Do not cover or encase the appliance during operation or after- wards to allow any moisture or dampness to evaporate. ▶ Do not place heavy objects or sources of heat or damp on top of the appliance. ▶ Do not use or store flammable detergent or dry cleaning agent in close vicinity to the appliance. ▶ Do not use any flammable sprays in close vicinity to the appli- ance. ▶ Do not wash any garments treated with solvents in the appli- ance without having dried them previously in the air.GB 1-Safety information

WARNING! Daily use ▶ Do not remove or insert the plug in the presence of flammable gas ▶ Do not hot wash foam rubber or sponge-like materials. ▶ Do not wash any laundry which is polluted with fl our. ▶ Do not open detergent drawer during any wash cycle. ▶ Do not touch the door during the washing process, it gets hot. ▶ Do not open the door if the water level is visibly over the port- hole. ▶ Do not force the door to open. The door is fitted with a self- lock device and will open shortly after the washing procedure is ended. ▶ Switch off the appliance after each wash programme and before undertaking any routine maintenance and disconnect the appli- ance from the electrical supply to save electricity and for safety. ▶ Hold the plug, not the cable, when unplugging the appliance. Maintenance / cleaning ▶ Make sure children are supervised if they carry out cleaning and maintenance. ▶ Disconnect the appliance from the electrical supply before un- dertaking any routine maintenance. ▶ Keep the lower part of the porthole clean and open door and detergent drawer if appliance is not in use to prevent odours. ▶ Do not use water spray or steam to clean the appliance. ▶ Replace a damaged supply cord only by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard. ▶ Do not try to repair the appliance by yourself. In case of repair please contact our customer service. Installation ▶ The appliance should be placed in a well-ventilated place. Ensure a location which allows opening the door fully. ▶ Never install the appliance outdoors in a damp place, or in an area which may be prone to water leaks such as under or near a sink unit. In the event of a water leak cut power supply and allow the machine to dry naturally.1-Safety information

Intended use This appliance is intended for washing machine-washable laundry only. Anytime follow the instructions given on the label of each gar- ment label. It is designed exclusively for domestic use inside the house. It is not intended for commercial or industrial use. Changes or modifi cations to the device are not allowed. Unintended use may cause hazards and loss of of all warranty and liability claims. WARNING! Installation ▶ Install or use the appliance only where the temperature is above 5 °C. ▶ Do not place the appliance directly on a carpet, or close to a wall or furniture. ▶ Do not install the appliance in direct sunlight or in the near of heat sources(e.g. stoves, heaters). ▶ Make sure that the electrical information on the rating plate agrees with the power supply. If it does not, contact an electri- cian. ▶ Do not use multi-plug adapters and extension cables. ▶ Make sure only the delivered electric cable and hose set are used. ▶ Make sure not to damage the electric cable and the plug. If dam- aged have it replaced by an electrician. ▶ Use a separate earthed socket for the power supply which is easy accessible after installation. The appliance must be earthed. Only for UK: The appliance’s power cable is fi tted with 3-cord (grounding) plug that fi ts a standard 3-cord (grounded) socket. Never cut off or dismount the third pin (grounding). After the appliance is installed, the plug should be accessible. ▶ Make sure the hose joints and connections are fi rm and there is no leakage.GB 2-Product description

2.1 Picture of appliance

Check the accessories and literature in accordance with this list (Fig.:2-3): Note:

1 Detergent /Softener drawer2 Worktop3 Programme selector 4 Panel5 Rating plater 6 Service ap 7 Adjustable feet 8 Door handle1 Transportation bolts (T1-T4)2 Back cover3 Back cover screws (S1-S6)Panel4 Power cord5 Water inlet valve6 Drain hose Inlet hose- assembly 5 Blanking plugs Drain hose bracket User manual Warranty-card 2-3 -3-Control panel

1 “On/Off “ button 2 Programme selector 3 Display 4 Detergent /Softener drawer

Press this button (Fig. 3-2) gently to switch on, the dis- play is shining, the indicator of the “Start/Pause” button is fl ashing. Press it again for about 2 seconds to switch off . If no panel element or programme is activated af- ter a while machine will shut down automatically.

3.2 Programme selector

By turning the knob (Fig. 3-3) one of 16 programmes can be selected, related LED will light up, its default settings will be displayed.

The display (Fig. 3-4) shows following information: ▶ Washing time ▶ End time delay ▶ Error codes and service information 3-4 5 Function buttons 6 “Delay” button 7 “Start/Pause“ button Note : Acoustic signal In following cases an acoustic signal sounds: ▶ when pressing a button ▶ when turning the programme selector ▶ at the end of programme ▶ in case of failures The acoustic signal can be deselected if necessary ; see DAILY USE. Cotton+CottonSyntheticHygienic Fast Daily WashDelicate/SilkHand WashBedding Spin Express 15 minBaby CareSportJeans Mix 3-2 3-3 SpeedSteam rinseDelayCotton+CottonSyntheticHygienic Fast Daily WashDelicate/SilkHand WashBedding Spin Speed upEnergyCapacitySpeedExpress 15 minBaby CareSportJeans Mix

The function buttons (Fig. 3-6) enables additional op- tions in the selected programme before programme starts. The related indicators are displayed. By switching off the appliance or setting a new pro- gramme, all options are disabled. If a button has multiple options, the desired option can be selected by pressing the button sequentially. To delete the setting or to cancel the setting process, press the function button until the desired LED lights or -in case of only one option- the LED switches off .

3.5.1-Function button „Temp.“

Press this button (Fig. 3-7) to change the washing temperature of the programme. If no value is illumi- nated the water will not heated. In conjunction with the “Steam” button, the child lock function can be switch on/off (see CHILD LOCK).

3.5.2-Function button “Speed”

Press this button (Fig. 3-8) to change or deselect the spin of the programme. If no value is illuminated the laundry will not spun. Note: Factory settings To get best results in each programme Haier has well defi ned specifi c default settings. If there is no special requirement default settings are recommended.

3.4 Detergent drawer

Open the drawer, three compartments can be seen (Fig. 3-5): Compartment 1 : Water inlet only, no detergent Compartment 2 : Detergent for programme Compartment : Softener, Conditioning agent etc. The recommendation on the type of detergents is suitable for the various washing temperatures, please refer to the manual of detergent. 3-5

3.5.3-Function button “Steam“

Press this button (Fig. 3-9) to activate the steam function.When this function is activated the default temperature is the maximum temperature of the programme selected.This function can be activated only with the following programmes: Hygienic, Baby clothes, Mix, Synthetics, Cotton.When the function is activated the led above the button will light up. Pushing again this button the function can be deactivated and the led above the button will turn off .When the function is activated the temperature of the programme cannot be changed. 3-7 3-8SpeedTemp.Speed SteamDelay Start/Pause Extra rinse

Press this button (Fig. 3-10) to rinse the laundry more intense with fresh water. This is recommended for people with sensitive skin. By pressing the button several times one to three ad- ditional cycles can be selected. They appear in the dis- play with //.

3.5.5 Function “Speed up“

This function saves time and energy. Preferable if laun- dry is slightly soiled. Press simultaneously button „Ex- tra rinse.“ and ”Delay” (Fig. 3-11) for about 3 seconds to activate the “Speed up” function; u is dis- played. This function is not available in all programmes (see PROGRAMMES). If “Temp.” button is pushed the “Steam” function will be deactivated.You can activate “Steam” function only before to start any programme. You cannot activate “Steam” function while the appliance is already ex- ecuting a programme.

3.7 „Start/Pause“ button

Press this button (Fig. 3-13) gently to start or inter- rupt the currently displayed programme. During pro- gramme setting and during programme run the LED above the button is shining, or if interrupted blinking.

Press this button (Fig. 3-12) to start the programme with a delay. End time delay could be increased in steps of 30 minutes from 0,5-24h. For example display off : means end of programme cycle will be in 6 hours and 30 minutes. Press “Start/Pause” button to activate the time delay. It is not applicable to programme SPIN. Note: Liquid detergent If using liquid detergent, it is not recommended to activate the end time delay.

Press button „Temp.“ and ”Steam” (Fig. 3-14) for 3 seconds simultaneously to block all panel elements against activation. For unlocking please press again the two buttons. The display shows (Fig. 3-15) if a button will be pressed, when the child lock is activated. The change is not running. 3-15 Extra rinse 3-10 Delay 3-12 Start/Pause 3-13 DelayExtra rinse Speed up 3-11 3-14 Temp. Speed Steam Steam 3-9GB 4-Programmes

Relating to dry laundry. Choose 90 °C wash temperature only for special hygienic requirements. *: water will not heated (no value is iluminated). Reduce detergent amount because programme duration is short. Max. load 1)TemperaturePreset spin speedin rpmFunctionin kg in °CPresetSteamExtra rinseSpeed upProgramme HW80selectablerange 2 1 Fibre typeCotton 8.0 * to 90 40

Cotton 1400 Synthetic 8.0 * to 60 40

Synthetic ormixed fabric

Lightly soiled mixed-laundry of cotton and synthetic

Baby Care 4.0 * to 90 40

/ Cotton/Synthetics 1000 Hygienic 4.0 * to 90 90

Sport 4.0 * to 40 20

Jeans 8.0 * to 60 30

/ Jeans 1000 Cotton 8.0* to 90

Lightly soiled laun-dry made of cotton or synthetic

Daily Wash4.0 * to 60 30

Machine-washable fabric made of wool or with wool content

Delicate laundry and Silk

Hand Wash2.0 * to 30 30

Laundry marked with symbol for handwash

Bedding 5.0 * to 60 40

Cleaning of the drum with special detergent

Detergent Softener or care product

• Standard programme for the Energy Labelling according to 2010/30 EU: Cotton 60°C / 40°C with max. spin speed setting . The standard 60°C and 40°C cotton programmes are suitable to clean normally soiled cotton laundry. They are the most effi cient programmes in terms of combined energy and water consumption for cotton laundry. Used water temperature may diff er from declared cycle temperature. Note: Auto Weight The appliance is equipped with a loading recognition. At low loading, energy, water and washing time will be reduced automatically in some programmes.

6.3 Preparing laundry

▶ Sort out clothes according to fabric (cotton, syn- thetics, wool or silk) and to how dirty they are (Fig. 6-3). Pay attention to the care labelling of wash- ing labels. ▶ Separate white clothes from coloured ones. Wash coloured textiles fi rst by hand to check if they fade or run. ▶ Empty pockets (keys, coins, etc.) and remove harder decorative objects (e.g. brooches). ▶ Garments without hems, delicates and fi nely wo- ven textile such as fi ne curtains are to be put into a wash bag to care for this delicate laundry (hand or dry cleaning would be better). ▶ Close zippers, velco fastener and hooks, make sure the buttons are sewn on tightly. ▶ Place sensitive items like laundry without fi rm hem, delicate underwear (Dessous) and small items such as socks, belts, bras, etc. in a wash bag. ▶ Unfold large pieces of fabric such as bed sheets, bedspreads etc. ▶ Turn jeans and printed, decorated or color-inten- sive textiles inside out; possibly wash separately. 6-3

Connect the washing machine to a power supply (220V to 240V~/50Hz; Fig. 6-1). Please refer also to section INSTALLATION.

6.2 Water connection

▶ Before connecting check the cleanliness and clar- ity of the water inlet. ▶ Tun on the tap (Fig.6-2). Note: Tightness Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap. CAUTION! Non-textile, as well as small, loose or sharp-edged items may cause malfunctions and damage of clothes and appliance. 6-1 6-26-Daily use

Care chart Washing Washable up to 95°C normal process Washable up to 60°C normal process Washable up to 60°C mild process Washable up to 40°C normal process Washable up to 40°C mild process Washable up to 40°C very mild process Washable up to 30°C normal process Washable up to 30°C mild process Washable up to 30°C very mild process Wash by hand max. 40°C Do not wash Bleaching Any bleaching allowed Only oxygen/ non -chlorine Do not bleach Drying Tumble drying possible normal temperature Tumble drying possible lower temperature Do not tumble dryr Line drying Flat drying Ironing Iron at a maximum temperature up to 200 °C Iron at a medial tem- perature up to 150°C Iron at a low temper- ature up to 110 °C; without steam (steam ironing may cause irre- versible damage) Do not iron Professional Textile Care Dry cleaning in tetra- chloroethene Dry cleaning in hy- drocarbons Do not dry clean Professional wet clean Do not professional wet clean

6.4 Loading the appliance

▶ Put in the laundry piece by piece ▶ Don‘t overload. Note the diff erent maximum load according to programmes! Rule of thumb for maximum load: Keep six inches between load and drum top. ▶ Close the door carefully. Make sure that no pieces of laundry are pinched.GB 6-Daily use

6.5 Selecting detergent

▶ Washing effi ciency and performance is determined by used detergent quality. ▶ Use only machine wash approved detergent. ▶ If needed use specifi c detergents, e.g. for synthetic and woolen fabric. ▶ Mind always detergent manufacturer recommendations. ▶ Do not use dry cleaning agents such as trichloroethylene and similar products. Choose the best detergent Programme Kind of detergent Universal Colour Delicate Special Softener Cotton L/P L/P - - o Synthetic L/P L/P L - o Mix L/P L/P - - o Wool - - - L o Bedding L/P L/P - - o Sport - - - L o Jeans L/P L/P L - o Hygienic L/P L/P L - o Fast L L - - o Express 15 min L L - - o Daily Wash L/P L/P L - o Baby Care L/P L/P - - o Delicate/Silk - - L - o Handwash - - - L o Spin L/P - - L - L = gel-/liquid detergent P = powder detergent O = optional

= no If using liquid detergent, it is not recommended to activate the time delay. We recomment by using: ▶ Laundry powder: 20°C to 90°C* (best use:: 40-60°C) ▶ Color detergent: 20°C to 60°C (best use: 30-60°C) ▶ Wool/delicate detergent: 20°C to 30°C (= best use:)

• Choose 90 °C wash temperature only for special hygienic requirements. +6-Daily use

6.7 Switch on the appliance

Press the „on/off “- button to switch on the appliance (Fig. 6-5). The LED of the „Start/Pause“ button is fl ashing.

6.6 Adding detergent

1. Slide out the detergent drawer. 2. Put the required chemicals into corresponding compartments (Fig. 6-4) 3. Push back the drawer gently. Note: ▶ Remove detergent residues before next wash cycle from the detergent drawer. ▶ Do not overuse detergent or softener. ▶ Please follow the instruction on the detergent package. ▶ Always fi ll the detergent just before the beginning of the wash cycle. ▶ Concentrated liquid detergent should be diluted before adding into compartment 2. ▶ The best use of liquid detergent is by using a dosing ball, which is given with the laun- dry into the washing machine. ▶ Do not use liquid detergent if „end time delay“ is selected. ▶ Carefully choose the programme settings according to the care symbols on all laun- dry labels and according to the programme table.

6.8 Select a programme

To get the best washing results, select a programme which fi ts the degree of soiling and sort of laundry type. Turn the programme knob (Fig. 6-6) to select the right programme. Related programme LED lights up and the default settings are displayed.

6.9 Add individual selections

Select required options and settings (Fig. 6-7); refer to CONTROL PANEL.Temp.Speed SteamDelay Start/Pause Extra rinse 6-7 6-4 Note: Odour removalBefore fi rst use we recommended to run programme SELF CLEAN with no load and small amount of detergent in washing agent compartment (2) or special machine cleaner to remove possibly corruptive residues.

1. At programme cycle end is displayed.

2. The appliance switches off automatically.

3. Remove laundry as soon as possible to go easy on it and to prevent more wrinkling.

4. Turn off the water supply.

5. Unplug the power cord.

6. Open the door to prevent formation of moisture and odours. Let it open while not used.

6.13 Activate or deactivate the buzzer

The acoustic signal can be deselected if necessary:

1. Switch on the appliance.

2. Select the SPIN programme.

3. Press the “Delay “button and “Extra rinse” button at the same time for about 3 sec-

onds. “ ” will be displayed and the buzzer will be deactivated. For activating the buzzer press these two buttons at the same time again. “ ” will be displayed. To interrupt a running programme press gently “Start/Pause“. The LED above the button is fl ashing. Press it again to resume operation. To cancel a running programme and all its individual settings

1. Press “Start/Pause” button to interrupt the running programme.

2. Press „On/Off “ button for about 2 seconds to switch the appliance off .

3. Select ‘’no Speed’’ and run programme SPIN(all lights are on) to drain the water.

4. Shut down and start up, then select a new programme and start it.

Note: Door lock ▶ For safety reasons the door is locked partially during the washing cycle. It is only pos- sible to open the door at the end of the programme or after the programme was can- celled correctly (see description above). ▶ In case of high water level, high water temperature and during spinning it is not pos- sible to open the door; is displayed Note: Standby mode / energy-saving mode The switched on appliance will go into standby-mode if it will not be activated within 2 minutes before starting the program or at the end of program. The display switsches off . This saves energy. To interrupt the standby mode push “Start/Pause“ button.

6.10 Start wash programme

Press “Start/Pause“ button (Fig. 6-8) to start. The LED of the „Start/Pause“ button stops fl ashing and lights up continuously Appliance operates according to present settings. Changes are only possible by cancelling the programme.

6.11 Interrupt - cancel wash programme

6.12 After washing7-Eco-friendly washing

Environmentally responsible use ▶ To achieve best use of energy, water, detergent and time you should use the recom- mended maximum load size. ▶ Do not overload (hand width clearance above laundry). ▶ For slightly soiled laundry select the Quick Wash programme. ▶ Apply exact dosages of each washing agent. ▶ Choose the lowest adequate washing temperature - modern detergents are ef- fi ciently cleaning below 60°C. ▶ Raise default settings only due to heavy staining. ▶ Select max. spinning speed if a domestic dryer is used.GB 8-Care and cleaning

8.1 Cleaning the detergent drawer

Take always care there are no detergent residues.Clean the drawer regularly (Fig. 8-1): 1. Pull out the drawer until it stops. 2. Press the release button and remove the drawer.3. Flush the drawer with water until it is clean and insert the drawer back in the appliance.

8.2 Cleaning the machine

▶ Unplug the machine during cleaning and mainte-nance. ▶ Use a soft cloth with soap liquid to clean the ma-chine case (Fig. 8-2) and rubber components. ▶ Do not use organic chemicals or corrosive sol-vents. Note: HygieneFor regular maintenance we recommend to run programme SELF CLEAN with no loadin order to remove possible corruptive residues quarterly. Add a small amount of deter-gent in washing agent compartment (2) - or use a special machine cleaner.

8.3 Water inlet valve and inlet valve fi lter

To prevent blockage of water supply by solid substanc-es like lime clean regularly the inlet valve fi lter. ▶ Unplug the power cord and turn off the water supply. ▶ Unscrew the water inlet hose at the back (Fig. 8-3) of the appliance as well as on the tap. ▶ Flush the fi lters with water and a brush (Fig. 8-4). ▶ Insert the fi lter and install the inlet hose.

8.4 Cleaning the drum

▶ Remove accidentally washed metal parts such as pins, coins, etc. from the drum (Fig. 8-5) because they cause rust stains and damage. ▶ Use a non-chloride cleaner for removing rust stains. Observe the warning hints of the cleaning agent manufacturer. ▶ Do not use any hard objects or steel wool for cleaning. 8-3 8-4 8-5

Energy Capacity 9kg rpm

Bedding Cotton + Baby clothes Hygienic Sportwear8-Care and cleaning

2. Open service fl ap. You can either use a coin or a

screwdriver (Fig. 8-9).

3. Provide a fl at container to catch leach water

(Fig. 8-10). There could be bigger amounts!

4. Pull the drainhose out and hold its end above the

container (Fig. 8-10).

5. Take the sealing plug out of the drainhose (Fig.

6. After complete drainage close drainhose (Fig.

8-11). and push it back into the machine.

If the appliance is left idle for a longer period:

and odours. Let door open while not used. Before next usage check carefully power cord, water inlet and drain hose. Make sure everything is properly installed and without leackage. WARNING! Scalding Risk! Water in the pump fi lter can be very hot! Before any action please ensure water has cooled down. Note: Hygiene After long periods of disuse we recommended to run programme SELF CLEAN with noload and small amount of detergent in washing agent compartment (2) or special machine cleaner to remove possibly corruptive residues..

Clean the fi lter once a month and check the pump fi lter for instance if the appliance: ▶ doesn´t drain the water. ▶ doesn´t spin. ▶ cause unusual noise while running. 8-8 8-98-6 8-78-10 8-118-12 8-13GB 8-Care and cleaning

CAUTION! ▶ Pump fi lter sealing has to be clean and unhurt. If the lid is not full tightened, water can escape. ▶ The fi lter must be in place, or it may lead to leakage.

9. Clean carefully pump fi lter, e.g. using running water

10. Refi x it thoroughly (Fig. 8-15).

• Drainage error, water is not fully drained within 6 minutes• Clean pump fi lter.• Check drain hose installation.

• Lock - error. • Shut the door properly.

• Water level not reached after 8 minutes.• Drain hose is self-syphoning..• Make sure that tap is fully opened and water pressure is normal.• Check drain hose installation.

• Water protective level - error.. • Contact the After sales service.. Many occuring problems could be solved by yourself without specifi c expertise. In case of a problem please check all shown possibilities and follow below instructions before you contact an after sales service. See CUSTOMER SERVICE. WARNING! ▶ Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. ▶ Electrical equipment should be serviced only by qualifi ed electrical experts, because improper repairs can cause considerable consequential damages.. ▶ A damaged power cable should only be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard.

9.1 Information codes

Following codes are displayed only for information referring to the washing cycle. No measures must be performed. Code Message:The remaining wash cycle time will be 1 hour and 25 minutes:The remaining wash cycle time including chosen end-time delay will be 6 hours and 30 min- utes //1/2/3 additional rinses are choosen (see FUNCTION BUTTONS „Extra rinse“).

The washing cycle is fi nished. The appliance shuts off automatically.

Function child lock is activated Door is closed because of high water level, high water temperature or spinning cy- cle.

The buzzer is deactivated The buzzer is activated Function “Sped up” is activatedGB 9-Troubleshooting

• Contact the After sales service..

• Contact the After sales service. Check and balance laundry load in the drum..

• Contact the After sales service..

• Machine leakage . • Open drain pump to drain,Shut down the machine. Contact the after sales service. Problem Cause Solution Washing machine fails to operate.

• Programme is not yet started. • Check programme and start it.

• Door is not properly closed. • Close the door properly.

• Machine has not been switched on. • Switch the machine on.

• Power failure. • Check power supply.

• Child lock is activated. • Deactivate child lock. Washing machine will not be fi lled with water.

• No water. • Check water tap.

• Inlet hose is kinked. • Check inlet hose.

• Inlet hose fi lter is blocked. • Unblock inlet hose fi lter.

• Water pressure is less than 0.03 MPa.

• Check water pressure.

• Door is not properly closed. • Close the door properly.

• Water supply failure. • Ensure the water supply. Machine is draining while being fi lled.

• Height of drain hose is below 80 cm.

• Make sure that drain hose is properly installed.

• Drain hose end could reach into water.

• Make sure the drain hose is not in water. Drainage failure. • Drain hose is blocked. • Unblock drain hose.

• Pump fi lter is blocked. • Clean pump fi lter.

• Drain hose end is higher than 100 cm above fl oor level.

• Make sure that drain hose is properly installed. Strong vibration while spinning.

• Not all transportation bolts have been removed.

• Remove all transportation bolts

• Appliance has no solid position.

• Ensure solid ground and a levelled position.

• Machine load is not correct. • Check load weight and balance. Operation stops before completing wash cycle.

• Water or electric failure. • Check power and water supply. Operation stops for a period of time.

• Appliance displays error code. • Consider display codes.

• Problem due to load pattern. • Reduce or adjust load.

• Programme performs soaking cycle.

• Cancel programme and restart.

Should the error messages reappear even after the taken measures, switch off the appli-ance, disconnect the power supply and contact the customer service.

9.4 In case of power failure

The current programme and its setting will be saved. When power supply is restored operation will be re-sumed. If a power failure cuts an operating wash programmedoor opening is mechanically blocked. To get out anylaundry water level should not be seen in the glassy porthole of the door - Danger of burns! Water level has to be lowered as described in “Pump fi lter”. Not til then pull lever (A) beneath service fl ap (Fig. 9-1) until door is unlocked by a gentle click. Afterwards refi x all parts.

9-1 Note: Foam formationIf too much foam is inspected during spin cycle, motor stops and drain pump will be ac-tivated for 90 seconds. If that elimination of foam fails up to 3 times, programme ends without spinning. Problem Cause SolutionExcessive foam fl oats drum and/or deter-gent drawer.• Detergent is not a appropriate. • Check detergent recommen-dations.

• Excessive use of detergent. • Reduce amount of detergent. Automatic adjust-ment of washing time.• Washing programme duration will be adjusted.• This is normal and doesn‘t af-fect functionality. Spinning fails. • Unbalance of laundry. • Check machine load and laun- dry and run a spinning pro-gramme again. Unsatisfactory wash-ing result.• Degree of pollution does not agree with selected programme. • Select an other programme.• Detergent quantitiy was not suf-fi cient.• Choose the detergent acc. to the degree of pollution and acc. to manufaturer specifi ca-tions.
• Maximum load has been exceeded. • Reduce loading.
• Laundry was unevenly distributed in the drum.• Loose the laundry.Washing powder residues are on the laundry.• Insoluble particles of detergent can remain as white spots on the laun- dry.
• Perform extra rinse.• Try to brush the points from the dry laundry.• Choose an other detergent.Laundry has grey patches.• Caused by fats such as oils, creams or ointments.• Pretreat the laundry with a special cleaner.GB 10-Installation

▶ Take the appliance out of the packaging. ▶ Remove all packaging material including polystyrene base, keep them out of childrens reach. While opening the package, water drops may be seen on plastic bag and port- hole. This normal phenomenon results from water tests in the factory.

10.2 Dismantle the transportation bolts

The transportation bolts are designed for clamping anti-vibration components inside the appliance during transportation to prevent inner damage.

1. Remove the back cover (Fig. 10-1).

2. Remove all 4 bolts on the rear side and take out

plastic spacers (A) from inner side of the machine (Fig. 10-2).

3. Replace back cover by inserting it in the two gaps

its convexity is facing out (Fig. 10-3).

4. Fill left holes with blanking plugs (Fig. 10-4).

10-210-1 Note: Packaging disposal Keep all packaging materials out of children´s reach and dispose them in an environ- mentally friendly manner.

10-3 10-4 Note: Keep in safe place Keep the transportation bolts in a safe place for later use. Whenever the appliance is to be moved at fi rst reinstall the bolts.

10.3 Moving the appliance

If the machine is to be moved to a distant location, replace the transportation bolts re- moved before installation to prevent damage:

1. Remove the blanking plugs.

2. Remove the back cover

3. Insert the plastic spacers and the transportation bolts.

4. Tighten the bolts with a spanner.

Adjust all feet (Fig. 10-7) to achieve a complete level position. This will minimize vibrations and thus noise during use. It will also reduce wear and tear. We recommend to use a spirit level for adjustment. Floor should be as stable and fl at as possible.

1. Loose the locknut (1) by using a wrench.

2. Adjust the high by turning the foot (2).

3. Tighten lock ut (1) against the housing.

10-7 Following connections are possible:

10.5.1 Drain hose to sink

▶ Hang the drain hose with the U-support over the edge of a sink with adequate size (Fig. 10-6). ▶ Protect the U-support suffi ciently against slip- ping.

10.5.2 Drain hose to waste water connection

▶ The internal diameter of the stand pipe with vent-hole must be minimum 40 mm. ▶ Put the drain hose for approx. 80 mm in the wastewater pipe. ▶ Attach the U-support and secure it suffi ciently (Fig. 10-7).

10.5 Drain Water Connection

Fix the water drain hose properly to the piping. The hose has to reach at one point a height between 80 and 100 cm above the appliance bottom line! If possible keep always drain hose fi xed to the clip at the appliance back. WARNING! ▶ Use only the supplied hose set for the connection. ▶ Never reuse old hose sets! ▶ Only connect to cold water supply. ▶ Before connection, check whether the water is clean and clear. 10-7 10-6GB 10-Installation

CAUTION! ▶ The drain hose should not be submerged in water and should be securely fixed and leak-free. If the drain hose is placed on the ground or if the pipe is at a height of less than 80 cm, the washing machine will continuously drain while being filled (self-si- phoning). ▶ Drain hose is not to be extended. If necessary contact after sales service.

10.5.3 Drain hose to sink connection

▶ The junction must lie above the siphon ▶ A spigot connection is usually closed by a pad (A). That must be removed to prevent any disfunc- tion (Fig. 10-8). ▶ Secure the drain hose with a clamp. 10-8

10.6 Fresh Water Connection

Make sure that the gaskets are inserted.

1. Connect the water inlet hose with the angled

end to the appliance (Fig. 10-9. Tighten the screw joint by hand.

2. The other end connect to a water tap with a

3/4“ thread (Fig. 10-10). 10-1010-9 Note: Aqua-stop-system: The aqua-stop system protects against water damage by automatically cutting the fresh water supply in case of a leaking hose. This is indicated by a red marker (A). The hose must be replaced.10-Installation

10.7 Electrical Connection

Before each connection check if: ▶ power supply, socket and fusing are appropriate to the rating plate. ▶ the power socket is earthed and no multi-plug or extension are used. ▶ the power plug and socket are strictly according. ▶ Only UK: The UK plug meets BS1363A standard. Put the plug into the socket (Fig. 10-11). WARNING! ▶ Ensure always that all connections (power supply, drain and fresh water hose) are fi rm, dry and leack free! ▶ Take care these parts are never to be crushed, kinked, or twisted ▶ If the supply cord is damaged, it must be replaced by the service agent (see warranty card) in order to avoid a hazard. . Note: Hygiene After each installation or long periods of disuse, before fi rst use and for regular mainte- tenance run programme SELF CLEAN with no load and small amount of detergent in washing agent compartment (2) or with special machine cleaner to remove possibly corruptive residues. 10-11GB 11-Technical data

1) Based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.2) Based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load. Actual water consumption will depend on how the appliance is used 3) Class G is the least effi ciency and Class A is the most effi cient.4) Based on the standard 60 °C cotton programme at full load and the standard 40 °C cotton programme at partial load 5) “Standard 60 °C cotton programme“ and “standard 40 °C cotton programme“ are standard washing programmes to which the information in the label and fi che relates. These pro-grammes are suitable to clean normally soiled cotton laundry and they are the most effi cient programmes in terms of combined energy and water consumption

6) In case there is a power management system.7) Based on the standard 60°C cotton programme at full load.

11.1 Product fi che according to regulation EU No. 1061/2010

Suppliers name or trade mark HaierSupplier´s model identifi erHW80-BP16636Rated capacity (kg) 8Energy effi ciency class A+++Energy consumption per year (AE in kWh/year)

Energy consumption of standard cotton programme 60°C, full load (kWh/cycle) Energy consumption of standard cotton programme 60°C, partial load (kWh/cycle) Energy consumption of standard cotton programme 40°C, partial load (kWh/cycle) Weighted power consumption of the off mode (W) 0.42Weighted power consumption of the left-on mode (W) 0.48Water consumption per year (AW in L/year)

Spin-drying effi ciency class

Airborne accustical noise (washing/spinning) in dB(A) re 1pW 52/78Type freestanding

11.2 Additional technical data

Dimension (HxWxD in mm) 850x595x600 Voltage in V 220-240 V~/50Hz Current in A 10 Max power in W 1950 Water pressure in MPa 0.03≤P ≤1 Netto weight in kg 72 HW80-BP16636

11.3 Standards and Directives

This product meets the requirements of all applicable EC directives with the correspon- ding harmonised standards, which provide for CE marking.GB 12-Customer service We recommend our Haier Customer Service and the use of original spare parts. If you have a problem with your appliance, please fi rst check section TROUBLESHOOTING. If you cannot fi nd a solution there, please contact ▶ your local dealer or ▶ the Service & Support area at www.haier.com where you can fi nd telephone numbers and FAQs and where you can activate the service claim. To contact our Service, ensure that you have the following data available. The information can be found on the rating plate. Model ____________________ Serial No. _____________________ Also check the Warranty Card supplied with the product in case of warranty. For general business enquiries please fi nd below our addresses in Europe: European Haier addresses Country* Postal address Country* Postal address Italy Haier Europe Trading SRL Via De Cristoforis, 12 21100 Verese ITALY France Haier France SAS 3-5 rue des Graviers 92200 Neuilly sur Seine FRANCE Spain Portugal Haier Iberia SL Pg. Garcia Faria, 49-51 08019 Barcelona SPAIN Belgium-FR Belgium-NL Netherlands Luxembourg Haier Benelux SA Anderlecht Route de Lennik 451 BELGIUM Germany Austria Haier Deutschland GmbH Hewlett-Packard-Str. 4 D-61352 Bad Homburg GERMANY Poland Czechia Hungary Greece Romania Russia Haier Poland Sp. zo.o. Al. Jerozolimskie 181B 02-222 Warszawa POLAND United Kingdom Haier Appliances UK Co.Ltd. One Crown Square Church Street East Woking, Surrey, GU21 6HR

Energy Capacity 9kg rpm

3NL 3-Bedieningspaneel

Energy Capacity 9kg rpm