VZUM79CT - Sink SMEG - Free user manual and instructions

Find the device manual for free VZUM79CT SMEG in PDF.

SMEG VZUM79CT - Sink
📄 42 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice SMEG VZUM79CT - page 6
Pick your language and provide your email: we'll send you a specifically translated version.
Brand SMEG
Model VZUM79CT
Product type Sink / Kitchen sink
Material Stainless steel
Number of basins 1
Installation type Built-in
Finish Brushed
Surface Non-porous
Daily cleaning Soft non-abrasive sponge and mild dish detergent, rinse and dry
Stubborn stain cleaning (light surfaces) Bleach solution (3/4) + warm water (1/4), let act 8h, rinse thoroughly
Stubborn stain cleaning (dark surfaces) Circular motions with non-abrasive sponge and detergent, rinse with warm water
Descaling Descaling product diluted in warm water, let act a few minutes, rinse
Weekly anti-scale treatment Fill with warm water + laundry detergent (liquid or powder) or tablet, let sit 5 to 6h, rinse
Forbidden products Steel wool, abrasive sponges, alkaline detergents (ammonia, caustic soda, drain cleaners)
Thermal precautions Do not place hot utensils directly (temperature up to 500°C); before pouring boiling liquids, run cold water and ensure at least 1 cm of water at the bottom
Shock precautions Avoid accidental impacts that may cause irreparable micro-damage
Recommended use Use a cutting board to cut or chop; do not cut directly on the surface
Warranty Failure to follow cleaning and maintenance instructions may void the conventional warranty
Manual available French, German, English, Spanish, Italian, Polish, Portuguese, Russian, Ukrainian and other languages on request
Download Free in PDF format at notice-facile.com

Frequently Asked Questions - VZUM79CT SMEG

How to clean my SMEG VZUM79CT sink daily?
Use a soft non-abrasive sponge and regular dish soap. Rinse thoroughly with warm water and dry carefully with a microfiber cloth.
How to remove stubborn stains on a light-colored sink?
Prepare a solution of 3/4 bleach and 1/4 warm water. Apply to stains, let sit for about 8 hours (preferably overnight), then rinse thoroughly and dry. If necessary, repeat 1 to 2 times.
How to remove stubborn stains on a dark-colored sink?
With a soft non-abrasive sponge moistened with regular dish soap, make small circular motions on the stains. Rinse with warm water and dry thoroughly. Repeat if necessary.
How to remove limescale stains on the sink?
Use a descaling and anti-corrosion product diluted in warm water. Spread evenly on the surface, gently scrub with a soft sponge in circular motions, let sit a few minutes according to product instructions, then rinse with warm water and dry.
Which cleaning products are forbidden on the SMEG sink?
Never use steel wool, abrasive sponges, or detergents containing alkaline substances such as ammonia, caustic soda, or drain cleaners. These products can irreparably damage the surface.
Can I place hot pans directly on the sink?
No, never place hot pots or pans directly on the sink surface as they can reach 500°C and cause discoloration and/or damage.
Can I cut or chop directly on the sink?
No, this can cause irreparable scratches. Always use a cutting board to protect the surface.
How to properly install the SMEG VZUM79CT sink?
Before installation, wash the sink with regular detergent and a soft sponge to remove production residues. Rinse and dry. Installation must be carried out by a qualified professional according to current standards. Silicone is not supplied.
How to prevent limescale stains?
Perform a weekly descaling treatment: fill the basin with warm water, add two tablespoons of liquid or powder laundry detergent (or a tablet), let sit for 5 to 6 hours, then rinse thoroughly and dry carefully.
Is the warranty affected by sink maintenance?
Yes, failure to follow the cleaning and maintenance instructions described in the manual may void the manufacturer's conventional warranty.

User questions about VZUM79CT SMEG

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Sink in PDF format for free! Find your manual VZUM79CT - SMEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VZUM79CT by SMEG.

USER MANUAL VZUM79CT SMEG

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

LAVELLO TOP

graph TD A["Step 1"] --> B["Central Structure"] C["Step 2"] --> B D["Step 3"] --> B E["Step 4"] --> B F["Step 5"] --> B G["Step 6"] --> B

TOP SILICONE LAVELLO

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with motion lines (no text or symbols)

2. NON-ROUTINE MAINTENANCE

Simple line drawing of a cooking pot with a crossed-out X symbol (no text or labels)

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 2

Before fitting the sink, it is advisable to wash it using standard dish detergent and a soft sponge to remove any manufacturing residues.

Rinse the sink thoroughly and dry it using a microfibre cloth.

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 3

STANDARD INSTALLATION

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK TOP

graph TD A["1"] --> B["Central Structure"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

SMEG VZUM79CT - STANDARD INSTALLATION - 6

UNDERMOUNT INSTALLATION

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

SMEG VZUM79CT - UNDERMOUNT INSTALLATION - 7

The packaging materials (plastic bags, expanded polystyrene, etc.) must not be left within reach of children as they are a potential hazard.

SMEG VZUM79CT - UNDERMOUNT INSTALLATION - 8

Installation and support should be undertaken by qualified individuals, in accordance with the applicable legal requirements.

The silicone is not included with the product. The sink shown in this guide is for illustrative purposes only.

SMEG VZUM79CT - UNDERMOUNT INSTALLATION - 9

1. ROUTINE MAINTENANCE

Cleaning your Smeg product is quick and simple. Even though the non-porous surface prevents liquids penetrating into the material, it is preferable to remove them immediately using a soft, non-abrasive sponge and standard dish detergent. You should then rinse the surface and dry it carefully using a microfibre cloth.

Simple line drawing of a hand wiping a surface with motion lines (no text or symbols)

2. NON-ROUTINE MAINTENANCE

Cleaning stubborn stains is not difficult: all you need to do is choose the right product and use it correctly.

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 1

For stubborn stains on LIGHT-COLOURED products, you can use a solution of bleach and warm water (3/4 to 1/4), leaving it to act for eight hours (we recommend that this cleaning be performed during the night). Afterwards, rinse thoroughly and dry the entire surface carefully using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 2

For stubborn stains on DARK-COLOURED products, you can remove them directly with a soft, non-abrasive sponge and standard dish detergent, using small circular movements. When finished, rinse using warm water and carefully dry the entire surface using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 3

To remove limescale stains, we recommend the use of a non-corrosive descaling product diluted with warm water. Distribute the solution uniformly over the entire surface of the product. Clean with a soft, non-abrasive sponge using small circular movements and leave the product to act for several minutes (follow the instructions and conditions for use on the product label). When finished, rinse using warm water and dry carefully using a microfibre cloth.

Failure to follow the cleaning and maintenance instructions stated in this manual may invalidate the standard warranty provided by the manufacturer.

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 4

To ensure that there is no change to the characteristics of the product, we recommend that users observe the following precautions:

- dry the surface of the product every day to avoid prolonged exposure to water that could lead to the build-up of limescale or stubborn stains

- do not use detergents that contain alkaline substances and aggressive liquids (such as ammonia, caustic soda or drain cleaners)

- do not remove traces of dirt using steel scourers or abrasive sponges that could damage the surface

- do not cut or chop directly on the surface of the product because this could cause irreparable scratches (always use chopping boards)

- avoid accidental knocks that could cause irreparable micro-damage

- do not place hot cookware, pans or coffee makers directly on the sink surface: stains from discolouration and/or damage could form in areas where hot items are placed

- avoid pouring boiling liquids directly into the sink without first turning on the cold tap and filling the sink with at least 1 cm of water, as this could damage the product

• to prevent the build-up of limescale, it is recommended that a descaling treatment be completed at least once a week. This is recommended in particular for dark-coloured sinks. Fill the tub with warm water and add two spoonfuls of liquid or powder dishwasher detergent or a dishwasher tab. Leave the solution for 5/6 hours. Rinse thoroughly and dry carefully.

Simple line drawing of a crossed-out kitchen counter with no text or symbols

Simple line drawing of a cooking pot with crossed-out diagonals (no text or symbols)

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 7

Do not put pans or coffee makers that have just been taken off the heat (which sometimes reach 500°C) directly into sink.

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK TOP

graph TD A["1"] --> B["Central Structure"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

SMEG VZUM79CT - NON-ROUTINE MAINTENANCE - 13

INSTALLATION UNDER THE TOP

1 2 PATTERN

15 mm Ø 11.5 mm

SILICONE

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with steam rising, crossed by a diagonal line (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK WORKTOP

graph TD A["1"] --> B["Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

UNDER-COUNTER INSTALLATIONSMEG VZUM79CT - INSTALLATION UNDER THE TOP - 14

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with three stacked components and upward arrows indicating motion (no text or symbols)

WORKTOP SILICONE SINK

graph TD A["①"] --> B["②"] C["③"] --> D["④"] E["⑤"] --> F["⑥"] G["⑦"] --> H["⑧"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with steam rising, crossed by a black X (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["①"] --> B["Central Structure"] C["⑤"] --> B D["③"] --> B E["④"] --> B F["⑥"] --> B G["②"] --> B

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

COUNTERTOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with crossed-out diagonals (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

DISHWASHER LID

graph TD A["1"] --> B["Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

LID SILICONE DISHWASHER

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a crossed-out kitchen counter with steam rising (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

Hand wiping a surface with a cloth (no text or symbols)

2. NON-PLANNED MAINTENANCE

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["Step 1"] --> B["Central Structure"] C["Step 2"] --> B D["Step 3"] --> B E["Step 4"] --> B F["Step 5"] --> B G["Step 6"] --> B

UNDER-COUNTER INSTALLATIONSMEG VZUM79CT - NON-PLANNED MAINTENANCE - 7

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

BLAT SILICONE DRAINER

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with a cloth (no text or symbols)

2. ROUTINE MAINTENANCE

Simple line drawing of a cooking pot with crossed-out diagonals (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with Chinese labels for each step.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

SALTCELLAR SILICONE KITCHEN SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application process, with Chinese labels.

Silicone

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Queant Melaying ① ②

15 mm Ø 11.5 mm

Silicone

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

Two hand icons with different textures, one covering a cloth and the other covering a surface (no text or symbols)

Simple line drawing of a crossed-out kitchen counter with no text or symbols

Simple line drawing of a cooking pot with crossed-out black lines (no text or symbols)

SMEG VZUM79CT - ROUTINE MAINTENANCE - 20

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : SMEG

Model : VZUM79CT

Category : Sink