JL010118NPF - Above ground pool JILONG - Free user manual and instructions

USER MANUAL JL010118NPF JILONG

Thank you for choosing the products manufactured by Jilong Company. Before using, please read the manual carefully and keep it with original package for future reference. Please carefully read them and keep them for future reference Contents: Pool, Instruction Manual, Repair patch.

Item No. Size Water capacity (75%) Water level

SAFETY INSTRUCTIONS:

1. Designate a person to be in charge of safety. The safety of children fully

depends on you! The infants below 5 are exposed to maximum danger. Accident does not always happen to others! Please keep it in mind at any time! Surveillance and action. Always keep your child under your supervision.

2. More supervision efforts are required when there are several persons

3. If possible, teach your child to swim.

4. Wet the neck, arms and legs before child enter the water.

5. Prohibit running or active games around swimming pool. Prohibit

6. The children not good at swimming or unattended must wear life

7. Never put toys nearby and inside the unattended pool.

8. Keep the water clean and sanitary.

9. Keep water treatment products out of reach of children.

10. Teach the child the self-rescue actions.

11. The door of protective barrier for unattended pool shall be always

13. However, these measures cannot substitute the attendance nearby.

14. When accident occurs: Pull the child out of water as early as

possible. Change the wet clothes and cover the child with warm blanket. Ask for help and act according to the method told to you.

15. Remember first-aid number and post it near the pool.

Warning: full supervision of adult is required at all times.3

1. One person choose a flat ground make sure there are no stone, gravel,

glass, and any other sharp and edgy objects. Never install the pool on a hard surface such as concrete or asphalt. Never install the pool close to trees (falling leaves) and any source of electric power.

2. Locate the pool as close as possible to a drain area, because it will be

impossible to move the pool once it is full with water.

3. Take out the product from package and check if any parts missing, unfold

it on the ground, lay flat, locate and open inflation valve(s).

4. It is recommended that you use only a hand or foot pump for inflation.

Caution: Do not use the high-pressure air to inflate! Do not over-inflate!

5. Slowly inflate all compartments, close and press all valves tightly after

6. Fill the water to the warning line marked on the inside wall of the pool.

Do not over fill. This process takes a half-hour. Regular Maintenance:

1. Renew the water regularly.

WARNING: Non-compliance of the maintenance rules may result in

serious hazards for health and especially for the children. Note: In order to keep your pool water cleaning, please change the water after each use.

2. In order to increase the life of the water in the pool, it is necessary to put

suitable chemicals as per the water’s PH level. Inquiry local retailer for suitable chemicals to correctly maintain the water in your pool. Read the instructions provided by the chemical product manufacturers carefully and follow them. Never put an empty swimming pool in the open air. Disassemble: Emptying it by opening the water drain, once the water is drained from the pool, deflate the pool wall, let the pool dry and fold it up carefully.4

Storage and Maintain: Clean the product with clear water, then leave it in shady and cool place for airing, fold it into original package and place it indoor for next use. In winter, the pool is not allowed to be placed at a temperature that is below 5 °C, otherwise the plastic film would be damaged. Suitable to be used in the open air. Caution: Do not use the alkali or acid detergent to clean product! Do not leave product exposed under sunlight directly because it will shorten the using-life of product. Repair Patch Instructions: (Small pinhole and small puncture leaks can be repaired with the included repair patch) a) Locate the leak place. b) Deflate and drain the water. c) Clean the area surrounding the leakage and wipe up all water from the surface. d) Take out the repair patch, cut it into required shape and size, which should be litter larger than the leaking area, put the patch on leaking area and press firmly. e) You can use it again after 24 hours drying of the repaired position. If the damage is bigger than 1” (2.5cm), we recommend using a Silicone or rubber based glue for repair. Please read warning statement on glue prior to use. Manufacturer: Shanghai Jilong Plastic Products Co. Ltd. No. 460 Lanxue Road, Huanglou, Pudong Area, Shanghai, 201205, P.R. China Tel: [phone] E-mail: [e-mail] Web: www.jilong.com5 Merci d'avoir choisi parmi les produits fabriqués par Jilong Company. Avant utilisation, veuillez lire le manuel attentivement et le conserver avec l'emballage d'origine pour référence future. À lire attentivement et à conserver pour consultation ultérieure. Contenu: Piscine, manuel d'instructions, rustine de réparation.

Item No. Size Water capacity (75%) Water level