SpeedCare GC6608 - Iron PHILIPS - Free user manual and instructions

USER MANUAL SpeedCare GC6608 PHILIPS

Always here to help you

Register your product and get support at

www.philips.com/welcome

4239_000_9025_3_Booklet Simple_A5_v4.indd 3 6/2/15 10:06 AMIMPORTANT

- Perform Calc-Clean process regularly for great steam and prolonged life (Fig. 1).

- Recommended water to use: distilled or demineralised water (Fig. 2).

Congratulations on your purchase and welcome to Philips! To fully benet from the support

that Philips offers, register your product at www.philips.com/welcome.

Read this user manual, the important information leaet, and the quick start guide on the

packaging carefully before you use the appliance. Save them for future reference.

General description (Fig. 3)

1 Water tank lling funnel

2 Carry lock (specic types only)

3 ’Iron ready’ light

4 Calc-Clean button with Calc-Clean light

12 Hose storage compartment

14 Smart Calc-Clean container

Setting the temperature

To set the required ironing temperature, turn the temperature dial to the appropriate position.

The appliance adjusts the steam automatically, depending on the ironing temperature set.

Temperature setting Automatic steam setting Fabric type

Synthetic fabrics (e.g., acetate, acrylic,

Wool, viscose, polyester and silk

3 to LINEN Cotton, linen

Recommended water to use: distilled or demineralised water

Your appliance has been designed to be used with tap water. If you live in an area with hard water,

fast scale build-up may occur. It is therefore recommended to use distilled or demineralised water

to prolong the lifetime of your appliance.

Do not add perfume, water from the tumble dryer, vinegar,

starch, descaling agents, ironing aids,

chemically descaled water or other chemicals, as they may cause water spitting, brown staining

or damage to your appliance.

4239_000_9025_3_Booklet Simple_A5_v4.indd 6 6/2/15 10:06 AMIMPORTANT - Cleaning and maintenance

Smart Calc-Clean System

Your appliance has been designed with a Smart Calc-Clean system to ensure that descaling and

cleaning is done regularly. This helps to maintain a strong steam performance and avoids dirt and

stains coming out of the soleplate over time. To ensure that the cleaning process is performed,

the steam generator gives regular reminders. Besides that, a second defence step to protect the

steam generator from scale is integrated: the steam function gets disabled if descaling is not done

after 1 hour steam ironing once the reminder came up. After descaling is done, the steam function

will be restored. This takes place regardless of the type of water used.

Sound and light Calc-Clean reminder

- After 1 to 3 months of use, the Calc-Clean light starts ashing and the appliance starts beeping

to indicate that you have to perform the Calc-Clean process (Fig. 4).

- You can continue steam ironing for 1 hour while the Calc-Clean light ashes and the appliance

beeps. After 1 hour, the steam function is automatically disabled. You have to perform the

Calc-Clean process before you can continue steam ironing. (Fig. 5)

Tip: You can continue to dry iron by not pressing the steam trigger.

Performing the Calc-Clean process with the Calc-Clean container

Do not leave the appliance unattended during the Calc-Clean process.

Caution: Do not interrupt the process by lifting the iron up from the Calc-Clean container,

as hot water and steam will come out of the soleplate.

1 Fill up the water tank halfway (Fig. 6).

Make sure that the appliance is plugged in and switched ON during the Calc-Clean process (Fig. 7).

3 Turn the temperature dial to CALC CLEAN (Fig. 8).

4 Place the Calc-Clean container on the ironing board or any other even, stable surface (Fig. 9).

5 Place the iron stably on the Calc-Clean container.

Note: The Calc-Clean container has been designed to collect scale particles and hot water during the

Calc-Clean process. It is perfectly safe to rest the iron on this container during the entire process.

6 Press and hold the Calc-Clean button for 2 seconds until you hear short beeps (Fig. 10).

7 During the Calc-Clean process, you hear short beeps and a pumping sound. Wait

approximately 2 minutes for the appliance to complete the process (Fig. 11).

8 When the Calc-Clean process is completed, the iron stops beeping (Fig. 12).

9 Wipe the iron with a piece of cloth and put it back on the base station (Fig. 13).

10 As the Calc-Clean container becomes hot during the Calc-Clean process,

wait approx. 5 minutes before you touch it.

11 Carry the Calc-Clean container to the sink, empty it and store it for future use (Fig. 14).

12 If necessary, you can repeat steps 1 to 11. Make sure that you empty the Calc-Clean

container before you start the Calc-Clean process.

Note: During the Calc-Clean process, clean water may come out of the soleplate if no scale has

accumulated inside the iron. This is normal.

4239_000_9025_3_Booklet Simple_A5_v4.indd 7 6/2/15 10:06 AMSafety auto-off mode (specic types only)

- To save energy, the steam generator switches off automatically when it has not been used for

15 minutes. The ‘iron ready’ light ashes.

- To reactivate the steam generator, set the on/off switch to ‘off’ position and then to ‘on’ position.

This chapter summarises the most common problems you could encounter with the appliance. If you

are unable to solve the problem with the information below, visit www.philips.com/support for

a list of frequently asked questions or contact the Consumer Care Centre in your country.

Problem Possible cause Solution

There is not enough water in

Fill the water tank beyond the MIN

indication. Press and hold the steam trigger

until steam comes out. It may take up to

30 seconds until steam comes out.

You have not pressed the steam

Press and hold the steam trigger until

You have set the temperature

Turn the temperature dial to 2 or higher.

The steam function has been

disabled until you have

performed the Calc-Clean

Perform the Calc-Clean process to

restore the steam function (see chapter

‘IMPORTANT - Cleaning and

This is the Calc-Clean reminder. Perform the Calc-Clean process within

1 hour after the Calc-Clean reminder

You have not done or have not

completed the Calc-Clean

Perform the Calc-Clean process to enable

the steam function again (see chapter

‘IMPORTANT - Cleaning and

You have not done or have not

completed the Calc-Clean

Perform the Calc-Clean process to enable

the steam function again (see chapter

‘IMPORTANT - Cleaning and

The safety auto-off function was

activated. This happens

automatically when the steam

generator has not been used or

the steam trigger has not been

pressed for more than 15

Set the on/off switch to ‘off’ position and

then to ‘on’ position.

The water tank is empty. Fill the water tank with water and press

the steam trigger until the pumping sound

becomes softer and steam comes out of

After the Calc-Clean process,

remaining water may drip out of

Wipe the soleplate dry with a piece of

cloth. If the Calc-Clean light still ashes and

the appliance still beeps, perform the Calc-

Clean process (see chapter ‘IMPORTANT

- Cleaning and maintenance’).

The Calc-Clean process has not

You have to perform the Calc-Clean

process again (see chapter ‘IMPORTANT -

Cleaning and maintenance’).

Impurities or chemicals present

in the water have deposited in

the steam vents and/or

Perform the Calc-Clean process regularly

(see chapter ‘IMPORTANT - Cleaning and

You have accidentally started

the Calc-Clean process (see

chapter ‘IMPORTANT -

Cleaning and maintenance’).

Switch off the appliance. Then switch it

back on again. Turn the temperature dial to

the desired temperature setting instead of

CÁLC CLEAN. Let the iron heat up until

the ‘iron ready’ light lights up steadily.

You have not set the

temperature dial to CALC CLEAN or you have not waited

for the iron to heat up.

See chapter ‘IMPORTANT - Cleaning and

You have not pressed the Calc-

Clean button for 2 seconds until

the appliance started beeping.

See chapter ‘IMPORTANT - Cleaning and