HCR7918EIMB - Fridge HAIER - Free user manual and instructions

USER MANUAL HCR7918EIMB HAIER

GB Thank you for purchasing a Haier Product. Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance. If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass this manual so that the new owner can become familiar with the appliance and safety warnings.

Legend Warning – Important Safety information General information and tips Environmental information

Disposal Help protect the environment and human health. Put the packaging in applicable containers to recycle it. Help to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with this symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

WARNING! Risk of injury or suffocation! Refrigerants and gases must be disposed of professionally. Ensure that the tubing of the refrigerant circuit is not damaged before being properly disposed of. Disconnect the appliance from the mains supply. Cut off the mains cable and dispose of it. Remove the trays and drawers as well as the door catch and seals, to prevent children and pets to get closed in the appliance.

Accessories Check the accessories and literature in accordance with this list:

User manual "OK "Sticker *Note: Only for model HCR7918EIMP/HCR7918EIMB/HCR7918EIMP(UK) User manual

GB Before switching on the appliance for the first time read the following safety hints!: WARNING! Before first use ▶ Make sure there is no transport damage. ▶ Remove all packaging and keep out of children´s reach. ▶ Wait at least two hours before installing the appliance in order to ensure the refrigerant circuit is fully efficient. ▶ Handle the appliance always with at least two persons because it is heavy. Installation ▶ The appliance should be placed in a well-ventilated place. Ensure a space of at least 10 cm above and around the appliance. ▶ Never place the appliance in a damp area or location where it might be splashed with water. Clean and dry water splashes and stains with a soft clean cloth. ▶ Do not install the appliance in direct sunlight or in the near of heat sources(e.g. stoves, heaters). ▶ Install and level the appliance in an area suitable for its size and use. ▶ WARNING: Keep ventilation openings in the appliance or in the in-built structure clear of obstruction. ▶ Make sure that the electrical information on the rating plate agrees with the power supply. If it does not, contact an electrician. ▶ The appliance is operated by a 220-240 VAC/50 Hz power supply. Abnormal voltage fluctuation may cause the appliance to fail to start, or damage to the temperature control or compressor, or there may be an abnormal noise when operating. In such case, an automatic regulator shall be mounted. ▶ Do not use multi-plug adapters and extension cables. ▶ WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance. ▶ WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged. ▶ Do not step on the power cable. ▶ Use a separate earthed socket for the power supply which is easy accessible. The appliance must be earthed. 4

GB WARNING! ▶ Only for UK: The appliance’s power cable is fitted with 3-cord (grounding) plug that fits a standard 3-cord (grounded) socket. Never cut off or dismount the third pin (grounding). After the appliance is installed, the plug should be accessible. ▶ WARNING: Do not damage the refrigerant circuit. Daily use ▶ This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. ▶ Children shall not play with the appliance. ▶ Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances, but not allowed to clean and install the refrigerating appliances. ▶ Keep away children under 3 years of age from the appliance unless they are constantly supervised. ▶ Cleaning and user maintenance shall not be made by children without supervision. ▶ The appliance must be positioned so that the plug is accessible. ▶ If coal gas of other inflammable gas is leaking into vicinity of the appliance, turn off the valve of the leaking gas, open the doors and windows and do not unplug the power cable of the refrigerator/freezer or any other appliance. ▶ Notice that the appliance is set for operation at the specific armbient range between 10 and 38°C. The appliance may not work properly if it is left for a long period at a temperature above or below the indicated range. ▶ Do not place unstable articles (heavy objects, containers filled with water) on top of the refrigerator/freezer, to avoid personal injury caused by falling or electric shock caused by contact with water. ▶ Do not pull on the door shelves. The door may be pulled slant, the bottle rack may be pulled away, or the appliance may topple. ▶ Open and close the door only with handles. The gap between the door and the cabinet is very narrow. Do not put your hands in these ares to avoid pinching your fingers. Open or close the refrigerator/freezer doors only when there are no children standing within the range of door movement. 5

GB WARNING! ▶ To avoid contamination of food, please respect the following instructions: ▶ – Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance. ▶ – Clean regularly surfaces that can come in contact with food and accessible drainage systems. ▶ – Clean water tanks if they have not been used for 48 h; flush the water system connected to a water supply if water has not been drawn for 5 days. ▶ – Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food. ▶ – Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice-cream and making ice cubes. ▶ – One-, two- and three-star compartments are not suitable for the freezing of fresh food. ▶ – If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance. ▶ Never store bottled beer or beverages, liquids in bottles or cans (besides high percentage spirits) especially carbonated beverages in the freezer, as these will burst during freezing. ▶ Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. ▶ Do not store medicines, bacteria or chemical agents in the appliance. This appliance is a household appliance. It is not recommended to store materials that require strict temperatures. ▶ Check the condition of food if a warming in the freezer has taken place. ▶ Do not set unnecessarily low temperature in the refrigerator compartment. Minus temperatures may occur at high settings. Attention: Bottles can burst ▶ Do not touch frozen goods with wet hands (wear gloves). Especially do not eat ice lollies immediately after removal from the freezer compartment. There is the risk to freeze or the formation of frost blisters. FIRST aid: keep immediately under running cold water. Do not pull away! ▶ Do not touch the inside surface of the freezer storage compartment when in operation, especially with wet hands, as your hands 6 may freeze onto the surface.

GB WARNING! ▶ Unplug the appliance in the event of a power interruption or before cleaning. Allow at least 7 minutes before restarting the appliance, as frequent starting may damage the compressor. ▶ WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Maintenance / cleaning ▶ Make sure children are supervised if they carry out cleaning and maintenance. ▶ Disconnect the appliance from the electrical supply before undertaking any routine maintenance. Allow at least 5 minutes before restarting the appliance, as frequent starting may damage the compressor. ▶ Hold the plug, not the cable, when unplugging the appliance. ▶ Do not clean the appliance with hard brushes, wire brushes, detergent powder, petrol, amyl acetate, acetone and similar organic solutions, acid or alkaline solutions. Please clean with special refrigerator/freezer detergent to avoid damage. Eventually use warm water and baking soda solution - about a tablespoon of baking soda to a litre/quart of water. Rinse thoroughly with water and wipe dry. Do not use cleaning powders or other abrasive cleaners. Do not wash removable parts in a dishwasher. ▶ Do not scrape off frost and ice with sharp objects. Do not use sprays, electric heaters like heater, hair dryer, steam cleaners or other sources of heat in order to avoid damage to the plastic parts. ▶ WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. ▶ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. ▶ Do not try to repair, disassemble or modify the appliance by yourself. In case of repair please contact our customer service. ▶ If the illuminating lamps are damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. ▶ Eliminate the dust on the back of the unit at least once in the year to avoid hazard by fire, as well as increased energy consumption. 7

GB WARNING! ▶ Do not spray or flush the appliance during cleaning. ▶ Do not use water spray or steam to clean the appliance. ▶ Do not clean the cold glass shelves or glass door with hot water. Sudden temperature change may cause the glass to break. ▶ If you leave your appliance out of use for an extended period, leave it open to prevent odour and unpleasant smells building up inside. Refrigerant gas information WARNING! The appliance contains the flammable refrigerant ISOBUTANE (R600a). Make sure the refrigerant circuit is not damaged during transportation or installation. Leaking refrigerant may cause eye injuries or ignite. If a damage has occurred, keep away open fire sources, thoroughly ventilate the room, do not plug or unplug the power cords of the appliance or any other appliance. Inform the customer service. In case of eyes get into contact with the refrigerant, rinse immediately it under running water and call immediately the eye specialist. WARNING: The refrigeration system is under high pressure. Do not tamper with it. Since the flammable refrigerants are used, please install, handle and service the appliance strictly according to the instruction and contact the professional agent or our after-sales service to dispose of the appliance. WARNING! For refrigerators with ice-water function, please pay attention to the following warning: For appliances not intended to be connected to the water supply: WARNING: fill with portable water only. For appliances intended to be connected to the water supply: WARNING: connect to potable water supply only. If you want to clean the water system, please refer to the User Manual. If you have any questions, please contact the after-sales service. 8

GB Safety information

Intended use This appliance is intended for cooling and freezing food. It has been designed exclusively for use in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other residential type environments as well as in bed-and-breackfast and catering business. It is not intended for commercial or industrial use. Changes or modifications to the device are not allowed. Unintended use may cause hazards and loss of warranty claims. Standards and directives and This product meets the requirements of all applicable EC directives with the corresponding harmonised standards and UK standards, which provide for CE and UKCA marking.

GB Model (HCR7918EIMP/HCR7918EIMB/HCR7918EIMP(UK)) (With Icemaker in door) 4 5

A: Fridge compartment 1 Control panel 2 Dispenser paddle 3 Drop tray 4 Vertical beam 5 Automatic Icemaker 6 Glass shelves 7 Humidity zone drawer 8 Water Filter cover 9 Handle lamp 10 Air duct and sensor (behind panel) 11 Back lamp 12 Bottle holder/Door rack 13 Air duct (behind drawers) 10

14 My Zone drawer 15 Freezer/Switch Zone lamp B: Freezer compartment 16 Sliding tray 17 Air duct 18 Freezer storage drawers 19 Bottle holder C: Switch Zone compartment 20 Sliding tray 21 Air duct 22 Switch Zone drawers 23 Bottle holder 24 Adjustable feet

I J K Buttons: A Auto Set mode selector B Holiday mode selector C My Zone drawer selector D Temperature adjustment button “-” E Temperature adjustment button “+” F Zone selector G Super-Cool selector H Super-Freeze selector I Filter reset function selector J Ice maker mode selector K Water intake function selector L Cubed ice function selector M Crushed ice function selector N Panel lock selector

GB Model (HCR7918ENMP) (Without Icemaker in door)

A: Fridge compartment 1 Vertical beam 2 Control panel 3 Glass shelves 4 Bottle holder/Door rack 5 Humidity zone drawer 6 Storage drawer 7 Handle lamp 8 Air duct and sensor (behind panel) 9 Back lamp 10 Bottle holder/Door rack 11 Air duct (behind drawers) 12 My Zone drawer 13 Freezer/Switch Zone lamp

B: Freezer compartment 14 Sliding tray 15 Water box 16 Air duct 17 Icemaker 18 Freezer storage drawers 19 Ice box 20 Bottle holder C: Switch Zone compartment 21 Sliding tray 22 Air duct 23 Switch Zone drawers 24 Bottle holder 25 Adjustable feet

Remove all packaging materials, keep them out of children`s reach and dispose them in an environmentally friendly manner. Clean the inside and outside of the appliance with water and a mild detergent before putting any food in it. After the appliance has been levelled and cleaned, wait for at least 2-5 hours before connecting it to the power supply. See Section INSTALLATION. Precool the compartments at high settings before loading with food. The function Power- Freeze helps to cool down the compartments quickly. The refrigerator temperature and freezer temperature are automatically set to 5° C and -18° C respectively. These are the recommended settings. If desired, you can change these temperatures manually. Please see ADJUST THE TEMPERATURE. 13

GB Sensor keys The buttons on the control panel are sensor keys, which already respond when lightly touched with the finger.

Switch on /of the appliance The appliance is in operation as soon as it is connected to the power supply. When the refrigerator is first powered on, the indicator “d” (Temperature display) illuminates. The fridge temperature, S-Zone temperature and freezer temperature are automatically set to 5° C, -6° C and -18° C respectively. The indicator “a” (Auto Set mode) illuminates. Maybe the panel lock is active.

Notice When the appliance is switched on after disconnection from the main power supply, it may take up to 12 hours for the correct temperatures to be reached. Empty the appliance before switching off. To switch off the appliance,pull the power cord out off the power socket.

Automatic lock: When the fridge door, freezer door and S-Zone door are closed and there is no key operation within 30 seconds, the display screen will be automatically extinguished and locked. Hold for 3s

Indicator on Display locked

▶ Manual lock: When the display screen is unlocked, press the button “N” (Panel lock selector) and hold for 3 seconds, the buzzer rings once, the indicator “n” (Panel lock) illuminates, and the display is locked.

Open door or any button Display lights up

Adjust the temperature The indoor temperatures are influenced by the following factors: ▶ Ambient temperature ▶ Frequency of door opening ▶ Amount of stored foods ▶ Installation of the appliance

GB Adjust the temperature for fridge 1. 2.

When the display screen is unlocked, press the button “F” (Zone selector). The buzzer rings once, the indicator “f1” (Fridge indicator) flashes, and then here comes the temperature setting mode of the fridge. Press the button “D” (Temperature adjustment button “-”) every time, the buzzer rings once, the set temperature of the fridge will be reduced by 1. The fridge temperature will display in the sequence of “5°C ->4°C->3°C ->2°C ->1°C ->9°C ->8°C->7°C ->6°C ->5°C ”. Press ‘-‘ 1 time

Press the button “E” (Temperature adjustment button “+”) every time, the buzzer rings once, the set temperature of the fridge will be increased by 1. The fridge temperature will display in the sequence of “5°C ->6°C ->7°C ->8°C ->9°C ->1°C ->2°C ->3°C ->4°C ->5°C ”. Press ‘+‘ 1 time

Notice After setting the temperature, if there is no operation within 5 seconds, the system will be automatically determined and save the set temperature.

Adjust the temperature for freezer 1. 2.

When the display screen is unlocked, press the button “F” (Zone selector). The buzzer rings once, the indicator “f2” (Freezer indicator) flashes, and then here comes the temperature setting mode of the freezer. Press the button “D” (Temperature adjustment button “-”) every time, the buzzer rings once, the set temperature of the freezer will be reduced by 1. The freezer temperature will display in the sequence of “-18°C ->-19°C->-20°C ->-21°C ->-22°C -> -23°C ->-24°C->-14°C ->-15°C ->-16°C ->-17°C ->-18°C”.

Press the button “E” (Temperature adjustment button “+”) every time, the buzzer rings once, the set temperature of the freezer will be increased by 1. The freezer temperature will display in the sequence of “-18°C ->-17°C ->-16°C ->-15°C -> -14°C ->-24°C ->-23°C ->-22°C ->-21°C ->-20°C ->-19°C ->-18°C”. Press ‘+‘ 1 time

GB Notice After setting the temperature, if there is no operation within 5 seconds, the system will be automatically determined and save the set temperature.

Adjust the temperature for Switch Zone (S-Zone) When the display screen is unlocked, press the button “F” (Zone selector). The buzzer rings once, the indicator “f3” (S-Zone indicator) flashes, and then here comes the temperature setting mode of the S-zone. 1.

Press the button “D” (Temperature adjustment button “-”) every time, the buzzer rings once, the set temperature of the S-zone will be reduced by 1. The S-zone temperature will display in the sequence of “-6°C ->-7°C->-8°C ->-9°C ->-10°C ->-11°C ->-12°C->-13°C ->-14°C ->-15°C ->-16°C ->-17°C->-18°C->5°C ->4°C ->3°C>2°C ->1°C ->0°C ->-1°C ->-2°C->-3°C->-4°C ->-5°C ->-6°C”. Press ‘-‘ 1 time

Press the button “E” (Temperature adjustment button “+”) every time, the buzzer rings once, the set temperature of the S-zone will be increased by 1. The S-zone temperature will display in the sequence of “-6°C ->-5°C->-4°C ->-3°C ->-2°C ->1°C ->0°C->1°C ->2°C ->3°C ->4°C ->5°C ->-18°C ->-17°C ->-16°C ->-15°C->14°C ->-13°C ->-12°C ->-11°C ->-10°C->-9°C->-8°C ->-7°C ->-6°C”. Press ‘+‘ 1 time

Notice After setting the temperature, if there is no operation within 5 seconds, the system will be automatically determined and save the set temperature.

Super-Cool function 1. 2. 3.

When the display screen is unlocked, press the button “G” (Super-Cool selector), the buzzer rings once, the indicator “g” (Super-Cool function) illuminates, and then the Super-Cool function will be turned on. When the indicator “g” (Super-Cool function) illuminates, press the button “G” (Super-Cool selector), the buzzer rings once, the indicator “g” (Super-Cool function) goes off, and then the Super-Cool function will be turned off. After the Super-Cool function is turned on, the refrigerator will automatically turn off the function when it reaches the set condition. If you want to exit manually, you can press the button “G” (Super-Cool selector) to turn it off.

GB Notice Under Super-cool state, the fridge temperature cannot be adjusted. If either button “D” (Temperature adjustment button “-”) or button “E” (Temperature adjustment button “+”) is pressed to adjust the temperature of fridge, the indicator “f1” (Fridge indicator) will flash with a prompt sound to indicate that this operation cannot be carried out. In the state of Super-cool function, the Auto-set function cannot be turned on at the same time due to different control modes. When you choose one function that conflicts with another function, the original function will automatically exit.

Super-Freeze function (Super-Frz) 1. 2. 3.

When the display screen is unlocked, press the button “H” (Super-Freeze selector), the buzzer rings once, the indicator “h” (Super-Freeze function) illuminates, and then the Super-Freeze function will be turned on.Press button “E” (Super-Frz). When the indicator “h” (Super-Freeze function) illuminates, press the button “H” (Super-Freeze selector), the buzzer rings once, the indicator “h” (Super-Freeze function) goes off, and then the Super-Freeze function will be turned off. After the Super-Freeze function is turned on, the refrigerator will automatically turn off the function when it reaches the set condition. If you want to exit manually, you can press the button “H” (Super-Freeze selector) to turn it off.

Notice Under Super-Freeze state, the freezer temperature cannot be adjusted. If either button “D” (Temperature adjustment button “-”) or button “E” (Temperature adjustment button “+”) is pressed to adjust the temperature of freezer, the indicator “f2” (Freezer indicator) will flash with a prompt sound to indicate that this operation cannot be carried out. Super-Freeze function is designed to keep nutrition value of frozen food, it will be freeze food in the shortest time. If large quantities of frozen food are to be frozen at one time, it is recommended that users take food that cannot be frozen out from the S-zone, turn the S-Zone temperature below -18°C, to use it as a freezer. Meanwhile, Super-Freeze function should be set 24h in advance, to make the freezer and S-zone own relatively low temperature and put food in. At this time, the freezing speed of the freezer and Szone is improved, food can be frozen quickly, the nutrition of food is effectively kept, and the storage becomes quite convenient.

When the display screen is unlocked, press the button “A” (Auto Set mode selector), the buzzer rings once, the indicator “a” (Auto Set mode) illuminates, and then the Auto Set function will be turned on. When the indicator “a” (Auto Set mode) illuminates, press the button “A” (Auto Set mode selector), the buzzer rings once, the indicator “a” (Auto Set mode) goes off, and then the Auto Set function will be turned off.

Indicator on Auto Set on

Indicator off Auto Set off

This refirgerator has human sensor function. The control panel, handle lamp and projection lamp will automatically light up if user approaches the refrigerator. Under unlocked state, hold the button “A” (Auto Set mode selector) for 3 seconds, the buzzer rings once, then the human sensor function will be turned off. The human sensor function can likewise be turned on with same operation.

Notice In Auto Set mode, the fridge or freeze temperature cannot be adjusted. If either button “D” (Temperature adjustment button “-”) or button “E” (Temperature adjustment button “+”) is pressed to adjust the temperature of fridge or freezer, the indicator “f1” (Fridge indicator) or “f2” (Freezer indicator) will flash with a prompt sound to indicate that this operation cannot be carried out. In Auto Set mode, due to different control methods, if the „Super-Cool“ or „Super-Freeze“ function is set, the indicator “a” (Auto Set mode) goes off, and then the Auto Set function will automatically exit. In Auto Set mode, the temperature of the S-Zone can be manually adjusted according to the needs.

Holiday mode Holiday mode is designed for not using the fridge for a long time. When the Holiday mode is turned on, the freezer is under normal control, and the temperature of fridge is automatically set to be 17 C°.The actual temperature is not higher than 17°C, which prevents peculiar smell caused by overtemperature, and helps reduce energy consumption at the same time. 1. When the display screen is unlocked, press the button “B” (Holiday mode selector), the buzzer rings once, the indicator “b” (Holiday mode) illuminates, and then the Holiday function will be turned on. 2. When the indicator “b” (Holiday mode) illuminates, press the button “B” (Holiday mode selector), the buzzer rings once, the indicator “b” (Holiday mode) goes off, and then the Holiday function will be turned off.

Indicator on Auto Set on

Under unlocked state, hold the button “B” (Holiday mode selector) for 3 seconds, the buzzer rings once, then the projection lamp will be turned off. The projection lamp function can likewise be turned with same operation.

Notice Under Holiday state, the fridge temperature cannot be adjusted. If either button “D” (Temperature adjustment button “-”) or button “E” (Temperature adjustment button “+”) is pressed to adjust the temperature of fridge, the indicator “f1” (Fridge indicator) will flash with a prompt sound to indicate that this operation cannot be carried out. Before using the Holiday function, please empty the fridge to prevent food goes bad in it. When the Holiday function is turned on, either “Auto Set” function or “Super-Cool” function cannot be turned on at the same time.

My Zone drawer 1. 2.

When the display screen is unlocked, press the button “C” (My Zone drawer selector), the buzzer rings once, the indicator “c1” (Fruit & Vegetable mode), the indicator “c2” (Quick Cool mode) and the indicator “c3” (0° C Fresh mode) will light up in sequence. When the indicator “c1” (Fruit & Vegetable mode) illuminates, press the button “C” (My Zone drawer selector), the buzzer rings once, the indicator “c1” (Fruit & Vegetable mode) goes off, and then the Fruit & Vegetable function will be turned off with the indicator “c2” (Quick Cool mode) illuminating. When the indicator “c2” (Quick Cool mode) illuminates, press the button “C” (My Zone drawer selector), the buzzer rings once, the indicator “c2” (Quick Cool mode) goes off, and then the Quick Cool function will be turned off with the indicator “c3” (0° C Fresh mode) illuminating. When the indicator “c3” (0° C Fresh mode) illuminates, press the button “C” (My Zone drawer selector), the buzzer rings once, the indicator “c3” (0° C Fresh mode) goes off, and then the 0° C Fresh function will be turned off with the indicator “c1” (Fruit & Vegetable mode) illuminating.

Indicator on Function on

Indicator on Function on

Indicator on Function on

Under unlocked state, hold the button “C” (My Zone drawer selector) for 3 seconds, the buzzer rings once, then the handle lamp will be turned off. The handle lamp can likewise be turned on with same operation. When the handle lamp flashes, the EPP function is turned on.

Notice When the refrigerator is connect to electricity for the first time, the Fruit & Vegetable function is automatically turned on.

GB Filter function When the refrigerator operates for six months, the reminder indicator “i” (Filter Reset function) will light up to remind users to replace with a new filter. When filter is replaced, hold the button “I” (Filter Reset function selector) for 3 seconds to cancel the reminder, the timing will reset with buzzer ringing.

Notice The normal service life of filter is six months. It is recommended to replace the filter every six months.

Ice maker mode 1. 2.

Under unlocked state, press the button “J” (Ice maker mode selector), the buzzer rings once, the indicator “j” (Ice maker mode) illuminates, and then the ice maker mode will be turned on. When the indicator “j” (Ice maker mode) illuminates, press the button “J” (Ice maker mode selector), the buzzer rings once, the indicator “j” (Ice maker mode) goes off, and then the ice maker mode will be turned off.

Indicator on Press 1 time Indicator off Ice making function on Ice making function off

Notice When the ice maker mode is turned off, Ice on / off flashes when the user takes Cubed ice or Crushed ice, prompting the user that the ice maker function is off.

Water intake function Under any state (locked or unlocked), press the button “K” (Water intake function selector), the buzzer rings once, the indicator “k” (Water intake function) illuminates, and then the water intake function will be turned on.

Indicator on Water intake function on

When the indicator “k” (Water intake function) illuminates, the indicator “l” (Cubed ice function) and the indicator “m” (Crushed ice function) go off. After the dispenser paddle is pressed, water will flow out of the intake port. When the water intake time reaches 150s, the refrigerator will beep and keep water until the time reaches 180s, the water will be cut off and the water valve will enter the 200s protection time, and then water intake can be carried out again. When the cumulative water intake time reaches 8min within 10min, the water valve enters the 200s protection time, and then water intake can be carried out again.

Cubed ice function Under any state (locked or unlocked), press the button “L” (Cubed ice function selector), the buzzer rings once, the indicator “l” (Cubed ice function) illuminates, and then the Cubed ice function will be turned on.

Indicator on Cubed ice function on

When the indicator “l” (Cubed ice function) illuminates, the indicator “k” (Water intake function) and the indicator “m” (Crushed ice function) go off. After the micro-switch of distributor is pressed, cubed ice will flow out of the intake port. When the ice maker is switched on for the first time, the indicator “l” and the indicator “m” synchronously illuminate with memory of last state. When the ice maker is firstly connected to electricity to operate, the Cubed ice function is turned off by default. Press the micro-switch of dispenser, the light of it turns on with the cover of it open. Then, the motor of crushing ice starts to rotate anticlockwise to push ice cubes. Loosen the micro-switch of dispenser, the light of it goes off with the motor of crushing ice stopping, the cover of dispenser will close after 5 seconds. Under the state of Cubed ice, when Cubed ice time is longer than 50 seconds, there will be buzzer starting to alert (knocking) to notice users to shut it down. When the time reaches 1 minute, it is forced to stop Cubed ice, and it is effective when the switch is pressed next time. During Cubed ice, if the fridge door is opened, the motor that delivering ice will stop, with the cover of dispenser closed, light of dispenser off, and Cubed ice will be stopped. It is forbidden to get ice with the fridge door open.

GB Crushed ice function Under any state (locked or unlocked), press the button “M” (Crushed ice function selector), the buzzer rings once, the indicator “m” (Crushed ice function) illuminates, and then the Crushed ice function will be turned on.

Indicator on Crushed ice function on

When the indicator “m” (Crushed ice function) illuminates, the indicator “k” (Water intake function) and the indicator “l” (Cubed ice function) go off. After the micro-switch of distributor is pressed, crushed ice will flow out of the intake port. Press the micro-switch of dispenser, the light of it turns on with the cover of it open. Then, the motor of crushing ice starts to rotate clockwise to push ice cubes. Loosen the micro-switch of dispenser, the light of it goes off with the motor of crushing ice stopping, the cover of dispenser will close after 5 seconds. Under the state of Crushed ice, when Crushed ice time is longer than 50 seconds, there will be buzzer starting to alert (knocking) to notice users to shut it down. When the time reaches 1 minute, it is forced to stop Crushed ice, and it is effective when the switch is pressed next time. During Crushed ice, if the fridge door is opened, the motor that delivering ice will stop, with the cover of dispenser closed, light of dispenser off, and Crushed ice will be stopped. It is forbidden to crush ice with the fridge door open.

Switch between degrees Celsius and Fahrenheit 1. 2.

Refrigerator factory sets degrees Celsius by default. When the display is unlocked, hold the button “H” (Super-Freeze selector) for 3s, the buzzer rings once, the indicator “e2” (Degrees Celsius) goes off, with the indicator “e1” (Degrees Fahrenheit) illuminating.

EPP function Under unlocked state, continuously press the button “H” (Super-Freeze selector) and button “A” (Auto Set mode selector) 5times (within 5 seonds), the buzzer rings once, then the EPP function will be turned off. The EPP function can likewise be turned on with same operation.

Door opening alarm If any door is kept open too long or the door is not closed well, the refrigerator will raise beep alarm at set intervals to remind you to close the door in time.

Power off memory The instantaneous working state of power off is remembered. After power on again, it still works according to the setting before power off.

Connect to potable water supply only. Connecting the water line must only be installed by a qualified plumber and in accordance with local legislation and regulations governing water quality.

Notice This water line installation is not covered by the appliance warranty.

Connecting water to the appliance 1.

Remove the rubber plug (1) from the water inlet valve.

Firmly push the water tube onto the water inlet valve and tighten up the collar nut. This water pipe needs to be cut from the middle and used, and the other section is used as a spare part.

Connecting to the water tap This feature is only available on some models. 1. Push the water tube into the hole of the tap connector supplied in the accessories. The pipe should be held firmly whilst the connector is pushed onto the pipe. 2. Ensure that the rubber washer is fitted to the inside of the tap connector before screwing it onto the tap. ▶ A separate connector or adaptor may need to be purchased if your tap fitting does not match the thread size of the connector provided.

Checking the Water Connection This feature is only available on some models. ▶ Turn on the water supply and switch on the appliance. Carefully check all fittings for possible leaks due to poorly fitted hoses. ▶ Press and hold the 3Sec.Filter Reset button for three seconds. The new water filter has been activated. ▶ Place a cup under the water dispenser to verify that water is flowing through the appliance. ▶ Check the connecting tube and joints for leaks once again. 24

GB Ice and water dispenser Before using the ice and water dispenser

Keep children away from the dispenser to prevent children playing with or damaging the controls.

Throw away the first few batches of ice (about 20 cubes and 7 cups of water). This is also necessary if the appliance has not been used for a long time. Clean the water dispensing system if they have not been used for 48 hours. Flush the water system connected to a water supply if water has not been drawn for 5 days. To clean the water dispensing system, flush the water through the dispenser about 5 minutes and throw away the first few batches of ice. Do not use a thin crystal cup or chinaware when dispensing water or ice.

If you open the freezer door while water is being dispensed, the water dispensing will stop. If you open the fridge door while water, cubed ice or crushed ice is being dispensed, dispensing will be paused. When you close the door, the selected item will continue to be dispensed. If the cup rim is small, water may splash out of the glass or miss it completely. Use a cup with a rim of over 68 mm in diameter when dispensing water, cubed ice or crushed ice. When the ice maker produces smaller ice cubes, or the cubes become lumped together, the amount of water supplied to the ice maker may be low due to insufficient water in the water tank. If ice is not used frequently or the freezer set temperature is too warm, it may also lump together. It is normal for milky / cloudy water to be dispensed after replacing the water filter. This air in the water will eventually clear and is safe to drink during this transition.

Using the ice and water dispenser Press the dispenser selection button repeatedly until the light above the indicator that you want illuminates. Press the dispenser paddle (1) with a glass or other container to dispense cubed ice, water or crushed ice.

GB Cleaning the dispenser Cleaning the ice and water outlet Wipe the water outlet (1) or ice outlet (2) frequently with a clean cloth as it may get dirty easily.

Notice Lint from a cloth may adhere to the outlets.

Cleaning the dispenser tray Wipe the entire area with a damp cloth. The dispenser tray may become wet easily due to spilled ice or water.

Automatic icemaker This feature is only available on some models. This feature may vary depending on model purchased.

Before using the in-door icemaker This feature is only available on some models. ▶ The icemaker produces ice normally when approximately 48 hours have passed after the appliance is initially installed. ▶ If the ice bin is completely filled with ice, ice production will stop. ▶ Sound of ice dropping into the ice bin is normal. ▶ If ice cubes are stored in the ice bin for a long period of time, they may clump together and may not be separated easily. In such a case, empty the ice bin and allow fresh ice to be made.

GB CAUTION! ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶

It is normal for milky or cloudy water to be dispensed after replacing the water filter. This air in the water will clear eventually and is safe to drink. The first ice and water dispensed may include particles or odour from the water supply line or the water tank. If discolored ice is dispensed, check the water tank and the water supply for a possible source. Do not use the ice or water until the problem is corrected. Do not touch the ice outlet or the automatic icemaker with your hand or a tool. Dispense ice into a glass before filling it with water or other beverages. Splashing will occur if ice is dispensed into a glass that already contains liquid. Never use a glass that is exceptionally narrow or deep. Ice may jam in the ice passage, affecting the performance of the appliance. Keep the glass at a proper distance from the ice outlet. A glass held too close to the outlet may prevent ice from dispensing. Dispose of the ice inside the ice bin if you go on vacation or if an extended power outage occurs. Water from melting ice may drop from the dispenser onto the floor.

In-door icemaker The automatic icemaker can automatically make 100-190 cubes, within a 24-hour period if conditions are favorable. This amount may vary according to the environment (ambient temperature around the appliance, frequency of the door being opened, amount of food stored in the appliance, etc.). (1) Auto Shutoff (feeler arm)

Removing/Refitting the ice storage bin The ice dispensing chute may become blocked with frost if only crushed ice is used. Remove the frost that accumulates by removing the ice bin and clearing the passage with a rubber spatula. Dispensing cubed ice periodically can also help prevent frost buildup.

Gently pull the handle to open the ice compartment. To remove the in-door ice bin, grip the front handle, slightly lift the lower part, and slowly pull out the bin as shown. Refit the in-door ice bin in the reverse sequence of their removal.

Do not touch the automatic icemaker’s mechanical parts with your hand or any mechanical implement. Doing so may cause serious injury or damage to the appliance. Do not disassemble, repair or alter the automatic icemaker. These tasks should only be done by a service technician. Keep children away from the dispenser. When refitting the ice bin, ensure that it is placed correctly.

Do not put this ice box in water or sprinkle it! If you need to clean this ice box. please wipe it with wet soft cloth.

Water filter Before replacing the water filter

Do not allow children to have access to small parts during the installation of this product. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

While the testing was performed under standard laboratory conditions, actual performance may vary. It is essential that the manufacturer’s recommended installation, maintenance and filter replacement requirements be carried out for the product to perform as advertised.

GB CAUTION! ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶

Do not install if water pressure exceeds 827 kPa. If your water pressure exceeds 827 kPa, you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure. Do not install where water hammer conditions may occur. If water hammer conditions exist, you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition. Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 37.8 °C. Protect filter from freezing. Drain filter when temperatures drop below 4.4 °C. The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or if a noticeable reduction in flow rate occurs. Where a backflow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion must be installed. Ensure all tubing and fittings are secure and free of leaks.

Replacing the water filter The filter must be changed every 6 months or when the water filter indicator on the control panel lights turns on or the water dispenser output decreases. To purchase a replacement water filter: - Use replacement cartridge: HRXWF, - Visit your local dealer or distributor. For further assistance, visit our website at www. haierspares.eu

Replacing the water filter causes a small amount of water (around 1 oz. or 25 cc) to drain. Wrap a cloth around the front end of the water filter cover to collect any leaking water. Hold the water filter upright, once it is removed, to prevent any remaining water from spilling out of the water filter. Uplift the water filter cover. Remove the disposable water filter. Replace with a new water filter. Insert the new filter into the filter head and rotate it clockwise until the arrow on the new filter lines up with the arrow on the filter head. Swing the filter back into the compartment. Close the water filter cover.

Press and hold the 3Sec.Filter Reset button for 3 seconds. Dispense water for approximately 5 minutes to remove trapped air and contaminants.

Failure to replace filters when required or using non Haier authorised water filters can cause the filter cartridge to leak and result in property damage.

Water Filter Model: Haier HRXWF ▶ ▶

System certified by IAPMO R&T against NSF/ANSI Standards 42, 53, 401 and P473 for the reduction of claims specified on the performance data sheet and at iapmort. org. Actual performance may vary with local water conditions.

Application Guidelines/Water Supply Parameters Service Flow: 0.5 gpm (1.89 lpm) Water Supply: Potable Water Water Pressure: 25-120 psi (172-827 kPa) Water Temperature: 33°F-100°F (0.6°C-38°C) Capacity: 170 gallons (643.5 liter)

GB It is essential that the manufacturer’s recommended installation, maintenance and filter replacement requirements be carried out for the product to perform as advertised. See Installation Manual for Warranty information.

Notice While the testing was performed under standard laboratory conditions, actual performance may vary. Replacement Cartridge: HRXWF For estimated costs of replacement elements please visit our website at www.haierspares.eu.

To reduce the risk associated with ingestion of contaminants: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

Notice To reduce the risk of water leakage or flooding, and to ensure optimal filter performance: ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶

Read and follow use instructions before installation and use of this system. Installation and use MUST comply with all state and local plumbing codes. Do not install if water pressure exceeds 120 psi (827 kPa). If your water pressure exceeds 80 psi (552 kPa), you must install a pressure-limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure. Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition. Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 1 00º F (38º C). Protect filter from freezing. Drain filter when temperatures drop below 33ºF (0.6ºC). Change the disposable filter cartridge every six months or sooner if you observe a noticeable reduction in water flow rate. Failure to replace the disposable filter cartridge at recommended intervals may lead to reduced filter performance and cracks in the filter housing, causing water leakage or flooding. This System has been tested according to NSF/ANSI 42, 53, 401 and P473 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42, 53, 401 and P473.

GB Multi-air-flow The refrigerator is equipped with a multi-air-flow system, with which cool air flows are located on every shelf level. This helps to maintain a uniform temperature to ensure that your food is kept fresher for longer.

Adjustable shelves The height of the shelves can be adjusted to fit your storage needs. 1. To relocate a shelf, remove it first by uplifting its front edge (1) and pulling it out (2). 2. To reinstall it, put it on the lugs on both sides and push it to the most rearward position until the rear of the shelf is fixed inside the slots in the sides

Notice: Ensure that all ends of a shelf are level.

My Zone drawer In this compartment the humidity level is lower than fridge compartment. This drawer is suitable to store fresh foods, quick cool foods, and fruits and vegetables.

Humidity box drawer In this compartment the humidity level is around 90%. It is controlled automatically by the system and is suitable to store fruits, vegetables, salads etc.

Do not remove the plastic cover inside the two zones. They maintain the humidity. Cold-sensitive fruits like pineapple, avocado, bananas, grapefruits are not recommended to be stored in these two drawers. Humidity level may be less than 90% with small amounts of vegetables, hence, large amounts of vegetables are prefered.

Switch Zone compartment The appliance is equipped with a Switch Zone compartment. Depending on the purpose desired temperature can be choosen by degree. Setting temperature can be adjusted between -18 °C and +5°C: 32

GB Removable door racks/bottle holder The door racks can be removed for cleaning: Place hands on each side of the rack, lift it upwards (1) and pull it out (2). In order to insert the door rack, the above steps are carried out in reverse order.

OPTIONAL: OK-temperature indicator The OK-temperature indicator can be used to determine temperatures below +4°C. Gradually reduce the temperature if the sign does not indicate “OK”.

Notice: When the appliance is switched on, it may take up to 12 hours for the correct temperatures to be reached.

Removable drawer To remove the drawer out, pull out to the maximum extent (1), lift and remove (2). In order to insert the drawer, the above steps are carried out in reverse order.

Storing large items Large items of e.g. frozen food can be stored after: ▶ removing the upper freezing tray, or ▶ after removing both upper freezing trays as well as the middle freezer drawer and storing the food directly on the lower freezing trays.

The Light The LED interior light comes on when the door is opened. The performance of the lights is not affected by any of the appliances other settings. 33

GB Energy saving tips ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶

Make sure the appliance is properly ventilated (see INSTALLATION). Do not install the appliance in direct sunlight or in the near of heat sources (e.g. stoves, heaters). Avoid unnecessarily low temperature in the appliance. The energy consumption increases the lower the temperature in the appliance is set. Functions like POWER- FREEZE consume more energy. Allow warm food to cool down before placing it in the appliance. Open the appliance door as little and as briefly as possible. Do not overfill the appliance to avoid obstructing the air flow. Avoid air within the food packaging. Keep door seals clean so that the door always closes correctly. Defreeze frozen food in the fridge storage compartment. The most energy-saving configuration requires the appliance keep drawers, food box and shelves on factory-fresh condition, and food should be places as far as possible without blocking the air outlet of the duct.

GB WARNING! Disconnect the appliance from the power supply before cleaning.

Cleaning Clean the appliance when only little or no food is stored. The appliance should be cleaned every four weeks for good maintenance and to prevent bad stored food odors.

WARNING! ▶ Do not clean the appliance with hard brushes, wire brushes, detergent powder, petrol, amyl acetate, acetone and similar organic solutions, acid or alkaline solutions. Please clean with special refrigerator detergent to avoid damage. ▶ Do not spray or flush the appliance during cleaning. ▶ Do not use water spray or steam to clean the appliance. ▶ Do not clean the cold glass shelves with hot water. Sudden temperature change may cause the glass to break . ▶ Do not touch the inside surface of the freezer storage compartment, especially with wet hands, as your hands may freeze onto the surface. ▶ In case of heating check the condition of frozen goods. ▶ ▶

Always keep the door gasket clean. Clean the inside and housing of the appliance with a sponge dampened in warm water and neutral detergent. 1. Please scrub the interior and exterior of the refrigerator, including door sealing, door rack, glass shelves, boxes and so on, with a soft towel or sponge dipped in warm water (you may add neutral detergent into the warm water). 2. If there is liquid spilled, remove all the contaminated parts, directly rinse with the flow water, dry and place it back into the fridge. 3. If there is spilled cream (such as the cream, melting ice cream), please remove all the contaminated parts, put into the warm water with about 40 °C for some time, then rinse with the flow water, dry and place it back into the fridge. 4. In case some small part or component gets stuck inside of the fridge (between shelves or drawers), use small soft brush to release it. If you could not reach the part, please contact Haier service ▶ Rinse and dry with soft cloth. ▶ Do not clean any of the parts of the appliance in a dishwasher. ▶ Allow at least 5 minutes before restarting the appliance as frequent starting may damage the compressor.

Defrosting The defrosting of the fridge and the freezer compartment are done automatically; no manual operation is needed. 35

GB Replacing the LED-lamps

WARNING! Do not replace the LED lamp yourself, it must only be replaced by either the manufacturer or the authorised service agent. The lamps adopts LED as its light source, featuring low energy consumption and long service life. If there is any abnormality, please contact the customer service . See CUSTOMER SERVICE.

Replaceable (LED only) light source by a professional. This product contains a light source of energy efficiency class E. Compartment Voltage Energy efficiency class Fridge back lamp

Non-use for a longer period If the appliance is not used for an extended period of time, and you will not use the Holidayfunction for the refrigerator: ▶ Take out the food. ▶ Unplug the power cord. ▶ Clean the appliance as described above. ▶ Keep the doors open to prevent the creation of bad odours inside.

Notice Turn the appliance off only if strictly necessary.

Moving the appliance 1. 2. 3.

Remove all food and unplug the appliance. Secure shelves and other moveable parts in the fridge and the freezer with adhesive tape. Do not tilt the refrigerator more than 45° to avoid damaging the refrigerating system.

WARNING! ▶ Do not lift the appliance by its handles. ▶ Never place the appliance horizontally on the ground. 36

GB Many occuring problems could be solved by yourself without specific expertise. In case of a problem please check all shown possibilities and follow below instructions before you contact an after sales service. See CUSTOMER SERVICE.

WARNING! ▶ Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. ▶ Electrical equipment should be serviced only by qualified electrical experts, because improper repairs can cause considerable consequential damages. ▶ A damaged supply should only be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Problem

The compressor does not work.

• Mains plug is not connected in the • Connect the mains plug. mains socket. • The appliance is in the defrosting • This is normal for an automatic defrosting cycle

The appliance runs • The indoor or outdoor tempera- • In this case, it is normal for the ture is too high. appliance to run longer. frequently or runs for a too long period • The appliance has been off power • Normally, it takes 8 to 12 hours for a period of time. for the appliance to cool down of time. completely. • A door of the appliance is not • Close the door/drawer and tightly closed. ensure the appliance is located on a level ground and there is no food or container jarring the door. • The door has been opened too fre• Do not open the door/drawer quently or for too long. too frequently. • The temperature setting for the freezer compartment is too low. • Set the temperature higher until a satisfactory refrigerator temperature is obtained. It takes 24 hours for the refrigerator temperature to become stable. • The door gasket is dirty, worn, • Clean the door/drawer gasket cracked or mismatched. or replace them by the customer service. • The required air circulation is not • Ensure adequate ventilation. guaranteed. The inside of the re- • The inside of the refrigerator frigerator is dirty and/ needs cleaning. or smells. • Food of strong odour is stored in the refrigerator. The appliance makes abnormal sounds.

• Clean the inside of the refrigerator. • Wrap the food thoroughly..

• The appliance is not located on • Adjust the feet to level the aplevel ground. pliance. • The appliance touches some ob- • Remove objects around the apject around it. pliance.

GB Possible Solution

It is not cold enough • The temperature is set too high. inside the appli- • Too warm goods has been stored. ance. • Too much food has been stored at one time. • The goods are too close to each other. • A door/drawer of the appliance is not tightly closed. • The door/drawer has been opened too frequently or for too long.

• Reset the temperature. • Always cool down goods before storing them. • Always store small quantities of food. • Leave a gap between several foods allowing air flowing. • Close the door/drawer.

It is too cold inside • The temperature is set too low. the appliance. • The Super-Frz/Super-Coolfunction is activated or is running too long.

• Reset the temperature. • Switch off the Super-Frz/Super-Cool function

Moisture formation • The climate is too warm and tooon the inside of the damp. refrigerator com- • A door/drawer of the appliance is partment. not tightly closed. • The door/drawer has been opened too frequently or for too long. • Food containers or liquids are left open.

• Increase the temperature.

• Do not open the door/drawer too frequently.

• Close the door/drawer. • Do not open the door/drawer too frequently. • Let hot foods cool to room temperature and cover foods and liquids.

Moisture accumu- • The climate is too warm and too • This is normal in damp climate lates on the refrigdamp. and will change when the huerators outside midity decreases. surface or between • The door is not closed tightly. The • Ensure that he door/drawer is the doors/door and cold air in the appliance and the tightly shut. drawer. warm air outside it condensates. Strong ice and frost • The goods were not adequately packaged . in the freezer com• A door/drawer of the appliance is partment. not tightly closed. • The door/drawer has been opened too frequently or for too long. • The door/drawer gasket is dirty, worn, cracked or mismatched. • Something on the inside prevents the door/drawer to close properly.

• Always pack the goods well.

The sides of the cabinet and door strip get warm.

• Close the door/drawer. • Do not open the door/drawer too frequently. • Clean the door/drawer gasket or replace them by new ones. • Reposition the shelves, door racks, or internal containers to allow the door/drawer to close.

The appliance makes abnormal sounds.

• The appliance is not located on • Adjust the feet to level the aplevel ground. pliance. • The appliance touches some ob- • Remove objects around the apject around it. pliance.

A slight sound is to • be heard similar to that of flowing water.

You will hear an • The fridge storage compartment • Close the door. door is open. alarm beep. You will hear a faint • The anti-condensation system is • This prevents condensation hum. working and is normal The interior lighting • Mains plug is not connected in the • Connect the mains plug. or cooling system mains socket. does not work. • The power supply is not intact. • Check the electrical supply to the room. Call the local electricity company! • The LED-lamp is out of order. • Please call the service for changing the lamp. Water leaking or • The water tank is not installed cor- • Refit the water tank into the dripping from the rectly fridge door, ensure it is pushed water dispenser • The water dispenser spout is not fully into the door. spout. screwed tight to the tank. • The water spout is screwed in firmly to the water tank. • The white silicon O ring is missing from the water spout. • Check the water spout has a white silicon O ring at the tank end before fitting the water spout to the water tank.

Troubleshooting Problem

The automatic ice- • Do not connect the water supply maker does not pipe to the appliance and open the produce ice or supply valve. produces a small • The water supply hose bent. • Dispensed a large amount of ice amount of ice. recently. • Ice maker function not on. • Open the appliance door frequently. • The appliance door do not completely closed.

GB Possible Solution • Connect the water supply pipe to the appliance and open the supply valve completely. • Straighten the water supply pipe. • It takes approximately 24 hours to produce more ice in the automatic icemaker. Please wait. • Turn “Ice on/off” on. • If you open the appliance door frequently, cold air will escape, lowering the speed of ice production. Do not open and close the appliance door frequently. • Close the appliance door completely.

Ice is not dispensed.

• Cubed or Crushed function is not • In the control panel, select selected. the modes for cubed ice and crushed ice alternately to dis• The ice path blocked. pense the ice. • Check the ice and clean the ice path regularly.

Water does not come out.

• The supply valve may be turned off. • The water dispenser tank may be empty. • The water supply hose bent. • Use unfiltered water. • Water filter clogged or filter not installed. • Water in reservoir is frozen because the controls are set too cold.

Water is leaking from dispenser.

• Air may be present in the water line • Dispense water for at least 3 system, causing water to drip after minutes to remove air from being dispensed. system.

Water tastes strange.

• The purified water or cold water not • Dispense water for at least 3 been used for an extended period minutes . of time. • Replace the water filter . • An expired filter is used.

• Open the water supply valve. • Fill the water dispenser tank. • Straighten the water supply pipe. • Replace the water filter in advance. • Replace the water filter . • Set the refrigerator control to a warmer setting and wait 24 hours. If the water does not dispense after 24 hours, call for service.

To contact the technical assistance, visit our website: https://corporate.haier-europe.com/en/ Under the section “website”, choose the brand of your product and your country. You will be redirected to the specific website where you can find the telephone number and form to contact the technical assistance.

Power interruption In the event of a power cut, food should remain safely cold for about 5 hours. Follow these tips during a prolonged power interruption, especially in summer: ▶ Open the door/drawer as few times as possible. ▶ Do not put additional food into the appliance during a power interruption. ▶ If prior notice of a power interruption is given and the interruption duration is longer than 5 hours, make some ice and put it in a container in the top of the refrigerator compartment. ▶ An inspection of the goods is required immediately after the interruption. ▶ As temperature in the refrigerator will rise during a power interruption or other failure, the storage period and edible quality of food will be reduced. Any food that defrosts should be either consumed, or cooked and refrozen (where suitable) soon afterwards in order to prevent health risks.

Memory function during power interruption After restoration of power the appliance continues with the settings that were set before the power failure.

WARNING! ▶ The appliance is heavy. Always handle with at least two persons. ▶ Keep all packaging materials out of children´s reach and dispose them in an environmentally friendly manner. ▶ ▶

Take the appliance out of the packaging. Remove all packaging materials.

Environmental conditions

The room temperature should always be between 1° C and 43° C, since it can influence the temperature inside the appliance and its energy consumption. Do not install the appliance near other heat-emitting appliances (ovens, refrigerators) without isolation.

Space requirement Required space when door is opened: W1=1217 mm W2=1528 mm D1=629 mm D2=1110 mm

Ventilaton cross-section To achieve sufficient ventilation of the appliance for safety reasons, the information of the required ventilation cross sections must be observed.

Aigning the appliance

The appliance should be placed on a flat and solid surface. 1. Tilt the refrigerator slightly backwards. 2. Set the feet to the desired level. Make sure the distance to the wall on the hinge side is at least 10 cm for the door to open properly.

Notice: For a free standing appliance: this refrigerating appliance is not intended to be used as a built-in appliance 42

The stability can be checked by alternately bumping on the diagonals. The slightly swaying should be the same in both directions. Otherwise the frame can warp; possible leaking door seals are the result. A low tendency to the rear facilitates the closing of the doors.

Fine tuning of the doors If the doors are not in one level, this mismatch can be remedied by following:

Using adjustable foot Rotate the adjustable foot according to the direction of arrow to turn up or down the foot. Contact after-sale service if needed.

Notice: In the future use of refrigerator, doors uneven phenomenon may occur to the weight of stored food. Then please adjust according to the above methods.

GB Waiting time To the maintenance-free lubrication oil is located in the capsule of the compressor. This oil can get through the closed pipe system during slanting transport. Before connecting the appliance to the power supply you have to wait at least 2 hours so that the oil runs back into the capsule.

Electrical connection Before each connection check if: ▶ power supply, socket and fusing are appropriate to the rating plate. ▶ the power socket is earthed and no multi-plug or extension. ▶ the power plug and socket are strictly according. Connect the plug to a properly installed household socket.

WARNING! To avoid risks a damaged power cord must be replaced by the customer service (see warranty card).

GB Ice and Water and Automatic Ice models

▶ Your Ice and Water and Automatic Ice refrigerator must be installed by a qualified plumber or Haier trained and supported service technician as incorrect plumbing can lead to water leaks. ▶ Haier appliances does not accept responsibility for damage (including water damage) caused by faulty installation or plumbing.

Notice: Remove the door bins from position A and install in position B before first using. ▶

Holding the front edge of the bins with one hand and taping the bottom of the bins alternately in the direction of arrow 1 with the other hand. After the bins are out of the door body, rotate forward and downward in the direction of arrow 2 to take it out and install it in position B.

WARNING! ▶ Only connect to drinking water supply. The water filter only filters impurities in the water and makes ice clean and hygienic. It cannot sterilize or destroy germs or other harmful substances. ▶ Too high water pressure in the hose can damage the appliance. Install a pressure reducer when the water pressure in the hose exceeds 0.6 MPa. ▶ Before connection, check whether the water is clean and clear.

GB Product fiche according to regulation EU No. 2019/2016 Brand Model name / identifier Category of the model Energy efficiency class

E E Annual energy consumption(kWh/year)(1)

Volume variable temperature compartment(L)

Volume Zero-Star compartment(L)

With icemaker in door

Star rating Temperature of other compartments>14°C Frost-free system Freezing capacity(kg/24h) Climate rating(2) Noise emission class and airborne acoustical noise emissions(db(A) re 1pW) Temperature rise time (h) Ice making capacity Type of appliance Others

Explanations: • Yes, featured (1) Based on the results of the standards conformance test over 24 hours. The actual consumption depends on the use and the location of the appliance.

(2) Climate rating SN: This appliance is intended for use in an ambient temperature of between + 10°C and +32°C Climate rating N: This appliance is intended for use in an ambient temperature of between + 16°C and +32°C Climate rating ST: This appliance is intended for use in an ambient temperature of between + 16°C and +38°C Climate rating T: This appliance is intended for use in an ambient temperature of between + 16°C and +43°C Additional technical data Voltage / Frequency Input current (A) Main fuse (A) Coolant Dimensions (H/W/D in mm)

220-240V ~/ 50Hz 2 (HCR7918EIMP/HCR7918EIMB/HCR7918EIMP(UK)) 1.8 (HCR7918ENMP) 16 R600a 1775 / 908 / 750

GB We recommend our Haier Customer Service and the use of original spare parts. If you have a problem with your appliance, please first check section TROUBLESHOOTING. If you cannot find a solution there, please contact ▶ ▶ ▶ ▶

your local dealer or our European Call Service-Center (see listed phone numbers below) or the Service & Support area at www.haier.com where you can activate the service claim and also find FAQs.

To contact our Service, ensure that you have the following data available. The information can be found on the rating plate.

Also check the Warranty Card supplied with the product in case of warranty. European Call Service-Center Country*

* For other countries please refer to www.haier.com Haier Europe Trading S.r.l Branch UK Westgate House, Westgate, Ealing London, W5 1YY *Duration of the guarantee of the refrigerating appliance: Minimum guarantee is: 2 years for EU Countries, 3 years for Turkey, 1 year for UK, 1 year for Russia, 3 years for Sweden, 2 years for Serbia, 5 years for Norway, 1 year for Morocco, 6 months for Algeria, Tunisia no legal warranty required. *The period of spare parts for the repair of the appliance: Thermostats, temperature sensors, printed circuit boards and light sources are available for a minimum period of seven years after placing the last unit of the model on the market. Door handles, door hinges, trays and baskets for a minimum period of seven years and door gaskets for a minimum period of 10 year, after placing the last unit of the model on the market. *For further information about the product, please consult https://eprel.ec.europe.eu/ or scan the QR on the energy label supplied with the appliance.

IT Modelli Ice and Water e Automatic Ice

CS Modely Ice and Water a Automatic Ice

Chladnička-mraznička