TN100 - Turntable TEAC - Free user manual and instructions

USER MANUAL TN100 TEAC

OWNER'S MANUAL ENGLISH IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

M The lightning flash with arrowhead in an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that could be of sufficient magnitude to constitute a risk of electric shock to persons.

V The exclamation point in an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION oo DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE. oo IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED. oo USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

5) Do not use this apparatus near water.

6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

CAUTION oo Do not expose this apparatus to drips or splashes. oo Do not place any objects filled with liquids, such as vases, on the apparatus. oo Do not install this apparatus in a confined space such as a book case or similar unit. oo The apparatus should be located close enough to the AC outlet so that you can easily reach the power cord plug at any time.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. oo The apparatus draws nominal non-operating power from the AC outlet with its POWER or STANDBY/ON switch not in the ON position.

oo The mains plug is used as the disconnect device, the disconnect device shall remain readily operable. oo Caution should be taken when using earphones or headphones with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss.

Apple and Mac OS are trademarks of Apple Inc., registered in the

U.S. and other countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.

IMPORTANT SAFETY INSTRUCTIONS (continued)

Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit.

Model for USA For European Customers

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Disposal of electrical and electronic equipment and batteries and/or accumulators

Declaration of Conformity

Responsible party: TEAC AMERICA, INC. Address: 1834 Gage Road, Montebello, California, U.S.A. Telephone number : 1-323-726-0303 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(b) By disposing of electrical/electronic equipment and waste batteries/accumulators correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

(c) Improper disposal of waste electrical/electronic equipment and batteries/accumulators can have serious effects on the environment and human health because of the presence of hazardous substances in the equipment. (d) The Waste Electrical and Electronic Equipment (WEEE) symbols, which show wheeled bins that have been crossed out, indicate that electrical/electronic equipment and batteries/accumulators must be collected and disposed of separately from household waste. If a battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as defined in the Battery Directive (2006/66/EC), then the chemical symbols for those elements will be indicated beneath the WEEE symbol.

Check to be sure the box includes all the supplied accessories shown below. Please contact the store where you purchased this unit if any of these accessories are missing or have been damaged during transportation. Rubber mat × 1

Model for USA/Canada: GPE053A-120050-1

Model for Europe: GPE053A-120050-Z ENGLISH This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • R eorient or relocate the equipment and/or the receiving antenna. •Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

(a) All electrical/electronic equipment and waste batteries/ accumulators should be disposed of separately from the municipal waste stream via collection facilities designated by the government or local authorities.

Owner’s manual (this document) × 1 oo Keep this manual in a safe place for future reference.

(e) Return and collection systems are available to end users. For more detailed information about the disposal of old electrical/electronic equipment and waste batteries/accumulators, please contact your city office, waste disposal service or the shop where you purchased the equipment.

Warranty card × 1 (for customers in the USA and

Canada only) oo See the back of this document for information about the warranty in Europe and other countries or areas.

Industry Canada’s Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003.

DECLARATION OF CONFORMITY We, TEAC AUDIO EUROPE, Liegnitzer Straße

6, 82194 Gröbenzell, Germany declare in own responsibility, the TEAC product described in this manual is in compliance with the corresponding technical standards.

CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notes about record styluses

Before use (continued)

Precautions for use oo Do not place anything on the turntable cover. Objects on the cover might cause noise due to vibrations or fall off, especially during playback.

If the surface of the unit gets dirty, wipe it with a soft cloth or use diluted mild liquid soap. Allow the surface of the unit to dry completely before using.

oo Avoid placing the unit in direct sunlight, close to a source of heat or in other similar conditions. Do not place the unit on top of an amplifier or other equipment that might generate heat that exceeds the operating temperature range of this unit. Doing so could cause discoloration, deformation or malfunction.

oo Do not use chemical cleaning cloths, thinner or similar substances as they could damage the surface of the unit.

oo As the unit could become warm during operation, always leave sufficient space around it for ventilation.

When installing this unit, leave a little space (at least 20 cm (8”)) between it and other devices and walls to allow good heat dissipation. When placing it in a rack, for example, leave at least 35 cm (13 3/4”) open above it and 10 cm (4”) open behind it. Failure to provide these gaps could cause heat to build up inside and result in fire. oo DO NOT MOVE THE UNIT DURING PLAYBACK. During playback, the record rotates. Do not lift or move the unit during playback. Doing so may damage the record, the stylus, the cartridge or the unit. oo Always remove the record before relocating or moving this unit. Moving the unit with a record on the turntable could damage the record, the stylus and the cartridge or could cause a malfunction. oo The voltage supplied to the unit should match the voltage as printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician.

VV CAUTION For safety, disconnect the power cord from the socket before cleaning.

Product registration

Customers in the USA, please visit the following TEAC website to register your TEAC product online. http://audio.teac.com/support/registration/

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site: http://teac-global.com/ 1) Open the TEAC Global Site. 2) In the TEAC Downloads section, click the desired language to open the Downloads website page for that language. NOTE If the desired language does not appear, click Other Languages. 3) Click the “Search by Model Name” section to open the Downloads page for that product. (Users in Europe should click the product name in the “Products” section instead.) 4) Select and download any updates that are needed.

oo Record styluses are precision parts, so handle them carefully to avoid bending or damaging their tips. If a stylus becomes bent or damaged, it might not be able to follow the audio groove precisely and could damage records or cause other malfunction. oo If a stylus becomes dirty, use a commercially available stylus cleaner or similar product to clean it. oo Do not rub the stylus tip forcefully with anything hard. Do not wipe the stylus with thinner or other chemicals. Doing so could harm it.

Replacing the stylus

A record stylus will become worn down after it has been used for about 500 hours. This will worsen the sound quality and could damage records. Replace the stylus with one that we recommend before this occurs. CAUTION oo Since loud noises could suddenly occur, put the unit into standby before changing the stylus. oo Be careful not to hurt your hand or the equipment. oo Be careful not to allow small children to accidentally swallow styluses.

When detaching a record stylus (the red part), hold the cartridge and pull the record stylus in the A direction to remove it.

A When installing a new stylus, insert it in the B direction, pushing it in so that its clasp is aligned with the cartridge.

B Replacement stylus (sold separately):

STL-122 diamond stylus (includes 2) For stylus replacements, contact your dealer or TEAC listed on the back of this Owner’s manual.

Names and functions of parts

C USB port (USB B type)

Connect this to the USB port of a computer to convert the audio signal from this unit to digital and output it to the computer (page 8).

B C D A Included AC adapter

R L A Analog audio output jacks (L/R)

These output analog audio signals. The PHONO EQ switch setting changes the type of output signal. Use the included audio cable (or commerciallyavailable ones) to connect other equipment to the output jacks of this unit. White (L) Red (R)

VV Precautions when making connections oo Do not plug the unit in until after making all connections. oo Carefully read the manuals of the devices that you are connecting and follow their instructions when making connections.

B PHONO EQ (audio output setting) switch

ON Signals that have been amplified by the built-in equalizer amp are output from the analog audio output jacks (L/R). THRU The MM cartridge signal is output directly through the analog audio output jacks (L/R). Use this when connecting to equipment that has PHONO inputs.

After completing all other connections, connect the included AC adapter to this jack.

Confirm that the power plug of the AC adapter is plugged into a power outlet.

ENGLISH When PHONO EQ is ON Connect to audio input jacks of amplifier, etc.

When PHONO EQ is THRU Connect to PHONO inputs of amplifier, etc.

D DC input connector

oo Unplug the power cord from the outlet when you are not planning to use the unit for an extended period of time. oo Do not use any AC adapter other than the one included.

VV Be sure to connect the power cord to an AC outlet that supplies the correct voltage. Connection to an outlet that supplies incorrect voltage could cause fire or electric shock. Hold the power plug when plugging it into an outlet or unplugging it. Never pull or yank on the power cord. Unplug the power cord from the outlet when you are not planning to use the unit for an extended period of time.

Press the STANDBY/ON button to turn the unit on or put it in standby.

Place records centered on the turntable.

Use this lever to lift the tone arm and to lower it to the record.

c Rotation speed setting switch

Set the rotation speed (RPM) suitable for the record.

This is a rest for the tone arm. Gently push the clasp to the right to release the tone arm before playing a record.

e Tone arm f Headshell

oo When shipped new from the factory, this is set to ON.

CAUTION When set to ON, if connected to the PHONO inputs of an amplifier, for example, the output from speakers and headphones will be very loud, which could damage equipment or harm hearing.

Opening and closing the turntable cover

Attaching the turntable cover

When holding a record or removing it from its sleeve, avoid touching the grooves by holding the record by its label and edge with one hand or by holding it by its edge with both hands.

1 Insert the hinges completely into the hinge holders at the left and right ends of the back of the main unit.

2 Align the tops of the hinges with the turntable cover hinge holders and insert them.

Removing the turntable cover

Hold both edges of the turntable cover and lift it slowly to remove it along with the hinges from the unit. Then, remove the hinges from the turntable cover.

Hold the front edge of the turntable cover and gently lift it open completely until it stops. The turntable cover will stay open in this position.

Gently lower the turntable cover until it is closed. VV Be careful not to pinch your hand, for example, when opening and closing the turntable cover.

Cleaning oo Fingerprints and dust on a record can cause noise and the sound to skip, as well as damage the record itself and the stylus. Use a commercially available record cleaner to clean records. Do not use thinner or anything other than a record cleaner. Such chemicals could harm the surface of the record. oo When using a record cleaner, wipe the surface of the record in a circular motion, following the grooves.

oo Do not leave records in places that are exposed to direct sunlight or are very hot or very humid. Leaving a record in such a condition for a long time could result in warping or other damage. oo Do not stack multiple records or place heavy objects on top of them. Do not leave records at an angle for long amounts of time either. Doing so could result in warping or other damage. oo Do not allow hard objects to directly touch the audio grooves. Doing so could cause scratches. oo After you finish playing a record, always put it back into its sleeve for storage. Leaving a record unprotected could result in warping or scratching. oo Do not use cracked records.

Playing records 1 Press the STANDBY/ON button on the back of the unit to turn it on.

4 Set according to the rotation speed

(RPM) of the record. The rotation speed can be set to 33 1/3, 45 or 78 RPM.

7 Move the tone arm to the edge of the record or the track where you want to start playback.

When playback finishes

When playback finishes, the tone arm automatically returns to the tone arm holder and the rotation stops. To stop playback manually, slightly lift the cue lever or the headshell hook and return the tone arm to its resting position.

2 Open the turntable cover slowly.

5 Move the tone arm clasp to the right to release the tone arm.

Lower the tone arm slowly until the stylus touches the record and playback begins. oo We recommend that you close the turntable cover during record playback to avoid dust.

VV Do not place anything on the turntable cover. Objects on the cover might cause noise due to vibrations or fall off, especially during playback.

VV B e careful not to pinch your hand, for example, when opening and closing the turntable cover.

6 Lift the cue lever.

oo During playback, do not touch the tone arm or the rotating record. oo Do not stop turntable rotation during playback.

During record playback, feedback could occur if the volume is too loud. If this happens, lower the volume of the amplifier.

3 Place a record on the turntable.

8 Lower the cue lever.

oo The tone arm may not return to the tone arm holder automatically depending on the record. In that case, move the tone arm back to the tone arm holder manually.

When playing a 45 RPM large-hole single record, use the included adapter.

Cue lever Tone arm oo You can also leave the cue lever down and move the raised tone arm over the record and then lower the tone arm slowly to start playback.

Recording with a computer

Connect this record player to a computer using a commercially-available USB cable to convert audio signals from a record to digital data and send them to the computer.

Supported operating systems

Computers running the following operating systems can be connected by USB to this unit (as of September 2015). Windows OS Windows 7 (32-bit, 64-bit) Windows 8 (32-bit, 64-bit) Windows 8.1 (32-bit, 64-bit) Windows 10 (32-bit, 64-bit) Mac OS X OS X Lion 10.7 OS X Mountain Lion 10.8 OS X Mavericks 10.9 OS X Yosemite 10.10 Use with operating systems other than these is not guaranteed. oo This unit will run with the standard OS driver, so there is no need to install a special driver.

Connecting with a computer

1 Turn the computer on. Confirm that the operating system is working correctly.

2 Use the USB cable to connect the computer and this unit.

3 Press this unit’s STANDBY/ON button to turn it on.

When they are connected, the computer will automatically detect this unit’s USB port and identify it as “USB Audio CODEC”. oo To record audio from this record player using a computer, you must first install software that can be used for audio recording on the computer. You may purchase the audio recording software that you prefer separately or download free software, such as Audacity (http://audacity.sourceforge.net/), from the Internet. As free software, Audacity is not supported by TEAC. oo When connected to a computer by USB and recording audio, do not do any of the following. Doing so could cause the computer to malfunction. Always quit the computer recording software before doing the following. u Disconnect the USB cable u Put the unit into standby

The following example explains the settings to make using Windows 7.

1 From the Start menu, select Control

Panel. 2 Click “Sound”. 3 Click the “Recording” tab, and confirm that “USB Audio CODEC” is set as the “Default Device”. 4 Select “Microphone USB Audio CODEC”, and click the Properties button. 5 Click the “Advanced” tab. 6 From the “Default Format” pull-down menu, select the audio quality (format) that you want to use for recording.

oo Use a USB cable with a ferrite core when connecting the unit to a computer.

“2 channel, 16 bit, 48000 Hz (DVD quality)” provides high audio quality but also requires more file space. Recording with a lower sampling frequency reduces the audio quality but also uses less file space.

If you experience a problem with this unit, please check the following items before requesting service. Something other than this unit could also be the cause of the problem. Please also check that the connected devices are also being used properly. If it still does not operate correctly, contact the retailer where you purchased the unit. No power. ee Confirm that the AC adapter is plugged into an outlet. Then, press the STANDBY/ON button to turn the unit on (page 5). There is no sound. ee When connecting this unit's analog audio output jacks to the audio input jacks of an amplifier or other equipment, set the PHONO EQ (audio output setting) switch to ON (page 5). Playback is not possible; there is noise. ee Confirm that the stylus cover (made of white plastic) has been removed. ee Clean the stylus (page 4). ee If the stylus is worn-out, replace it (page 4). ee Place the unit as far away as possible from TVs, microwave ovens and other devices that emit electromagnetic waves.

The pitch is wrong. ee Set the rotation speed (RPM) to match the record

(page 7). The sound is skipping. ee Vibrations will cause skipping. Place this unit in a stable location. ee If the record is dirty, wipe it clean. ee Do not use scratched records.

oo Performance data is specified at 20°C.

USB port that can receive power from computer USB buses (Full Speed). . . . . . . . . . . . . . . . USB connector type B USB bus power support . . . . . . . . . . . . . . . . . . . . 5 V, 500 mA oo Use a commercially-available USB cable to connect the unit to a computer to receive power from it.

Sampling frequency 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz Quantization bit depth . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-bit

Included accessories

Rubber mat × 1 45 RPM adapter × 1 Turntable × 1 Turntable cover × 1 Hinges × 2 Audio cable × 1 AC adapter × 1 Model for USA/Canada: GPE053A-120050-1 Model for Europe: GPE053A-120050-Z Owner’s manual (this document) × 1 Warranty card × 1 (for customers in the USA and Canada only)

oo Specifications and appearance are subject to change without notice. oo Weight and dimensions are approximate. oo Illustrations in this owner's manual might differ slightly from production models.

Windows 7 (32 bits, 64 bits) Windows 8 (32 bits, 64 bits) Windows 8.1 (32 bits, 64 bits) Windows 10 (32 bits, 64 bits) Mac OS X OS X Lion 10.7 OS X Mountain Lion 10.8 OS X Mavericks 10.9 OS X Yosemite 10.10

In countries/regions other than the USA,

Canada and Europe This warranty gives you specific legal rights, and you may also have other rights that vary by country, state or province. If you have a warranty claim or request, please contact the dealer where you bought the product. 该保证书赋予了顾客特定的合法权利，并且因国 家，州或省等地域的不同，顾客可能拥有其他权 利。如需申请或要求保修，请与购买本产品的销 售店进行联系。

1834 Gage Road, Montebello, California 90640 U.S.A.

TEAC AUDIO EUROPE Liegnitzer Straße 6, 82194 Gröbenzell, Germany

This device has a serial number located on its rear panel. Please record the serial number and retain it for your records.

Model name: TN-100 Serial number: 1015.MA-2207B