DEH-X3700UI - Car stereo PIONEER - Free user manual and instructions

USER MANUAL DEH-X3700UI PIONEER

Connections/Installation 13 Additional Information 15

• In the following instructions, a USB memory or USB audio player are referred to as “USB device”. • In this manual, iPod and iPhone are referred to as “iPod”.

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service Station.

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards. • Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the device.

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids. • Always keep the volume low enough to hear outside sounds. • The Pioneer CarStereo-Pass is for use only in Germany. CAUTION This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

Optional remote control

The remote control CD-R320 is sold separately.

Frequently used operations

The available buttons vary depending on the unit.

DEH-X3700UI M.C. (multi-control) dial

SRC (source)/OFF Purpose

Press SRC/OFF to turn on the power.

Press and hold SRC/OFF to turn off the power.

Press SRC/OFF repeatedly.

Press DISP repeatedly.

Return to the previous display/list

Return to the normal display from the menu Press BAND/

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off.

/DIMMER Display indication

DEH-2700UI SRC (source)/OFF Indication

M.C. (multi-control) dial

Appears when a lower tier of the menu or folder exists. Appears when the

Appears when the local seek tuning function is set (page 9).

Appears when a traffic program is received. Appears when traffic announcements are received (page 9). Appears when the sound retriever function is set (page 10). Appears when random/shuffle play is set. Appears when repeat play is set.

* This button is referred to as DISP in the manual.

Appears when the iPod control function is set (page 8).

Detaching the front panel

Detach the front panel to prevent theft. Remove any cables and devices attached to the front panel and turn off the unit before detaching it.

[QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C. dial to select [QUIT :NO], then press to confirm. Press the M.C. dial to confirm the settings.

• You can cancel the menu setting by pressing SRC/OFF.

• These settings can be made at any time from the SYSTEM settings (page 10) and INITIAL settings (page 5).

Canceling the demonstration display (DEMO OFF)

• Avoid subjecting the front panel to excessive shock. • Keep the front panel out of direct sunlight and high temperatures. • Always store the detached front panel in a protective case or bag.

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the display.

Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set at this time, turn the M.C. dial to select [NO], then press to confirm. Turn the M.C. dial to select the options, then press to confirm. To proceed to the next menu option, you need to confirm your selection.

LANGUAGE Select the language to display the text information from a

[ENG](English), compressed audio file. [РУС](Russian), [TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

Press the M.C. dial to display the main menu.

Turn the M.C. dial to select [SYSTEM], then press to confirm. Turn the M.C. dial to select [DEMO OFF], then press to confirm. Turn the M.C. dial to select [YES], then press to confirm.

Press and hold SRC/OFF until the unit turns off.

Press and hold SRC/OFF to display the main menu. Turn the M.C. dial to select [INITIAL], then press to confirm. Turn the M.C. dial to select an option, then press to confirm.

Select the FM tuning step from 100 kHz or 50 kHz.

SP-P/O MODE [REAR/SUB.W] [SUB.W/SUB.W]

Select when there is a full-range speaker connected to the rear speaker output leads and there is a subwoofer connected to the

RCA output. Select when there is a passive subwoofer connected directly to the rear speaker output leads and there is a subwoofer connected to the RCA output.

Select when there are full-range speakers connected to the rear speaker output leads and RCA output. If there is a full-range speaker connected to the rear speaker output leads, and the

RCA output is not used, you may select either [REAR/SUB.W] or [REAR/REAR].

Select [YES] to initialize the unit settings. The unit will be restarted automatically.

(Some of the settings may be retained even after resetting the unit.)

To seek a station manually

1 After selecting the band, press

/ to select a station.

Press and hold / then release to seek an available station. Scanning stops when the unit receives a station. To cancel seek tuning, press / .

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 9).

To store stations manually

1 While receiving the station you want to store, press and hold one of the number buttons (1/

Receiving preset stations to select the band from [FM1], [FM2], [FM3], [MW] or [LW]. to 6/

/ buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the FUNCTION settings (page 9).

during FM reception.

Turn the M.C. dial to select a program type from [NEWS/INFO], [POPULAR],

[CLASSICS] or [OTHERS]. Press the M.C. dial. The unit begins to search for a station. When it is found, its program service name is displayed.

The six strongest stations are stored on the number buttons (1/

After selecting the band, press the M.C. dial to display the main menu.

Turn the M.C. dial to select [FUNCTION], then press to confirm. Turn the M.C. dial to select [BSM], then press to confirm.

• To cancel the search, press the M.C. dial.

• The program of some stations may differ from that indicated by the transmitted PTY. • If no station is broadcasting the type of program you searched for, [NOT FOUND] is displayed for about two seconds and then the tuner returns to the original station.

For more details about PTY list, visit the following site: http://www.pioneer.eu/eur/products/25/121/tech/CarAudio/PTY.html

Best stations memory (BSM)

NOTES Press a number button (1/

The unit searches for a station by PTY (program type) information.

Press SRC/OFF to select [RADIO].

) until it stops flashing.

The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the

Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS (radio data system) function only works in areas that broadcast RDS signals for FM stations.

* The FLAC files are only compatible with DEH-2700UI.

1 Insert the stereo mini plug into the AUX input jack. 2 Press SRC/OFF to select [AUX] as the source.

Disconnect headphones from the device before connecting it to the unit.

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 11).

You can make various adjustments in the FUNCTION settings (page 9). Note that the following operations do not work for an AUX device. To operate an AUX device, use the device itself.

M.C. (multi-control) dial

SRC (source)/OFF Select a folder/album*1

Select a track/song (chapter)

Fast forward or reverse

Search for a file from a list

1 Press to display the list.

2 Turn the M.C. dial to select the desired file (folder) name or category, then press to confirm. 3 Turn the M.C. dial to select the desired file, then press to confirm. Playback starts.

1 Insert a disc into the disc loading slot with the label side up. To eject a disc, stop playback first then press

1 Open the USB port cover. 2 Plug in the USB device/iPod using an appropriate cable.

View a list of the files in the selected folder/ Press the M.C. dial when a folder/category category*1 is selected.

Play a song in the selected folder/ category*1

Press and hold the M.C. dial when a folder/ category is selected.

Alphabetical search (iPod only)

1 Press to display the list.

2 Turn the M.C. dial to select the desired category list, then press to enter the alphabetical search mode. (Turning the M.C. dial twice also enters the alphabetical search mode.) 3 Turn the M.C. dial to select a letter, then press to display the alphabetical list. To cancel alphabetical search, press / DIMMER.

CAUTION Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device connected directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

MTP connection A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable supplied with the device. However, depending on the connected device and the numbers of the files in the device, audio files/songs may not be able to be played back via MTP. Note that MTP connection is not compatible with WAV and FLAC* file formats, and cannot be used with the MIXTRAX function.

Shuffle all play (iPod only)

Pause/resume playback

[1]: Effective for low compression rates [2]: Effective for high compression rates

Return to root folder (USB only)*1

Press and hold BAND/

Switch between compressed audio and CD- Press BAND/

Change drives in USB device

Press BAND/ (Devices that support the USB mass storage device class protocol only)

*1 Compressed audio files only

*2 This function is disabled when USB is selected as a source and the MIXTRAX function is on.

Useful functions for iPod

Link play mode You can access songs based on the artist, album, or genre currently playing. 1 While listening to a song, press and hold to enter the link play mode. 2 Turn the M.C. dial to select the mode ([ARTIST], [ALBUM], [GENRE]), then press to confirm. The selected song/album will be played after the currently playing song. NOTE The selected song/album may be canceled if you use functions other than those from the link play mode (e.g. fast forward and reverse).

You can control the unit via a connected iPod. The following iPod models are not compatible with this function. – iPod nano 1st generation, iPod with video 1 Press BAND/ during playback, then select the control mode. [CONTROL iPod/CTRL iPod]: The unit’s iPod function can be operated from the connected iPod. [CONTROL AUDIO/CTRL AUDIO]: The unit’s iPod function can only be operated by the buttons on the unit. In this mode, the connected iPod cannot be turned on or off.

• Pressing iPod can also switch the control mode (only for DEH-2700UI).

• Switching the control mode to [CONTROL iPod/CTRL iPod] pauses song playback. Use the connected iPod to resume playback. • The following operations are still accessible from the unit, even if the control mode is set to [CONTROL iPod/CTRL iPod]. – Pause, fast forward/reverse, song/chapter selection • The volume can only be adjusted from the unit.

About MIXTRAX (USB/iPod only)

(Only for DEH-X3700UI) The MIXTRAX function creates a non-stop mix of your music library, accompanied by illumination effects. For details on MIXTRAX settings, see page 12. NOTES • This function is not compatible with an Android device connected via MTP. • When USB is selected as a source and the MIXTRAX function is in use, the sound retriever function is disabled. • Depending on the file/song, sound effects may not be available. • Turn the MIXTRAX function off if the illumination effects it produces interfere with driving.

Press MIX to turn MIXTRAX on/off.

You can enjoy listening to an application on an iPhone via the unit. In some cases, you can control an application by using the unit. For details on compatible devices, visit our website. Important Use of third party apps may involve or require the provision of personally identifiable information, whether through the creation of a user account or otherwise, and for certain applications, the provision of geolocation data. ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO NOT USE THAT THIRD PARTY APP.

This function is compatible with iPhones and iPod touches installed with iOS 5.0 or later.

NOTE PIONEER IS NOT LIABLE FOR ANY THIRD PARTY APPS OR CONTENT, INCLUDING WITHOUT LIMITATION THEIR ACCURACY OR COMPLETENESS. THE CONTENT AND FUNCTIONALITY OF SUCH APPS ARE THE SOLE RESPONSIBILITY OF THE APP PROVIDER.

The menu items vary according to the source. Menu Item

Playback of an application via the unit

[TALK], [STANDARD], [MUSIC]

Connect this unit with the mobile device.

• iPhone via USB (page 7) Press SRC/OFF to select [APP].

Match the sound quality level with the broadcast signal conditions of the FM band signal.

(Available only when FM band is selected.)

BSM Store the six strongest stations on the number buttons (1/ to 6/

Operate the mobile device to start up the application.

REGIONAL Basic operations

You can make various adjustments in the FUNCTION settings (page 9).

FM SETTING Operation

Fast forward or reverse

Pause/resume playback

Limit the reception to the specific regional programs when AF (alternative frequencies search) is selected. (Available only when FM band is selected.)

LOCAL FM: [OFF], [LV1], [LV2], [LV3], [LV4] Restrict the tuning station according to the

MW/LW: [OFF], [LV1], [LV2] signal strength.

You can adjust various settings in the main menu.

Press the M.C. dial to display the main menu.

Turn the M.C. dial to select one of the categories below, then press to confirm. • FUNCTION settings (page 9) • AUDIO settings (page 10) • SYSTEM settings (page 10) • ILLUMINATION settings (page 11) • MIXTRAX settings (page 12) Turn the M.C. dial to select the options, then press to confirm.

Receive current traffic information if available.

(Available only when FM band is selected.)

Allow the unit to retune to a different frequency providing the same station. (Available only when

FM band is selected.)

AF Interrupt the currently selected source with news programs. (Available only when FM band is selected.)

Assign or buttons to seek the stations one by one (manual tuning) or select a station from the preset channels.

[1] (effective for low compression Enhance compressed audio and restore rich rates), [2] (effective for high sound. compression rates), [OFF]

Not available when; • USB is selected as a source and the MIXTRAX function is set to on. • The FLAC file is played back. (DEH-2700UI only)

AUDIO BOOK Menu Item

Cut-off frequency: [50HZ], [63HZ], [80HZ], [100HZ], [125HZ], [160HZ], [200HZ] Output level: [–24] to [+6] Slope level: [–12], [–24] [0] to [+6]

Change the playback speed. (Not available when

[CONTROL iPod/CTRL iPod] is selected in the control mode.)

Only frequencies lower than those in the selected range are output from the subwoofer.

[FASTER], [NORMAL], [SLOWER]

Select the bass boost level.

HPF SETTING Cut-off frequency: [OFF], [50HZ], Only frequencies higher than the high-pass filter

[63HZ], [80HZ], [100HZ], [125HZ], (HPF) cutoff are output from the speakers. [160HZ], [200HZ] Slope level: [–12], [–24]

PAUSE Pause or resume playback.

Adjust the front and rear speaker balance.

BALANCE Adjust the volume level for each source except

FM. Each of the below combinations are set to the same setting automatically. • USB, iPod, and APP (iPhone)

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings (page 5). *3 Not available when [OFF] is selected in [SUB.W].

Adjust the left and right speaker balance.

EQ SETTING [SUPER BASS], [POWERFUL], Select or customize the equalizer curve. [NATURAL], [VOCAL], [CUSTOM1], [CUSTOM1] can be set separately for each source. [CUSTOM2], [FLAT] However, each of the below combinations are set to the same setting automatically. Select an equalizer band and • USB, iPod, and APP (iPhone) level for further customizing. [CUSTOM2] is a shared setting used for all Equalizer band: [80HZ], [250HZ], sources. [800HZ], [2.5KHZ], [8KHZ] Equalizer level: [+6] to [–6]

You can also access to these menus when the unit is turned off. Menu Item [ENG](English), [РУС](Russian), [TUR](Turkish)

Set the clock (page 5).

Compensate for clear sound at low volume.

Select the language to display the text information from a compressed audio file.

[OFF], [LOW], [MID], [HI]

LANGUAGE Select the subwoofer phase.

Select the time notation.

ILLUMINATION settings

Display the item on the sub information display.

Select from “SPEANA,” “LEVEL METER,” “SOURCE,” “CLOCK,” and “OFF.”

INFO DISPLAY (Only for DEH-X3700UI)

Search for a different station with the same programming, even if using a preset station.

Set to [ON] when using an auxiliary device connected to the unit.

AUX MUTE MODE (Only for DEH-2700UI)

[MUTE], [20dB ATT], [10dB ATT]

Mute or attenuate sound automatically when a signal from equipment with a mute function is received.

Reduce the battery power consumption.

Turning on the source is the only operation allowed when this function is on.

* [PW SAVE] is canceled if the vehicle battery is disconnected and will need to be turned back on once the battery is reconnected. When [PW SAVE] is off, depending on connection methods, the unit may continue to draw power from the battery if your vehicle’s ignition does not have an ACC (accessory) position.

Select color for the keys/display of the unit from

12 preset colors, [SCAN] or [CUSTOM]*. • [SCAN]: Cycle through a variety of colors automatically. • [CUSTOM]*: 1 Press and hold the M.C. dial until the color setting display appears. 2 Set the primary color (R (red)/G (green)/B (blue)) and brightness level ([0] to [60]). You cannot select a level below 10 for all three of R (red), G (green), B (blue) at the same time. You can also customize the preset colors. Select one of the preset colors, then press and hold the M.C. dial until the color setting display appears.

[KEY COLOUR], [DISP COLOUR],

COLOUR (Only for DEH-X3700UI)

* The CUSTOM setting is only available for [KEY COLOUR] and [DISP COLOUR].

[SYNC ILLUMI]*, [SYNC CLOCK], [MANUAL]

Change the display brightness.

* Only for DEH-X3700UI Change the display brightness.

The available setting ranges differ depending on [DIM SETTING].

ILLUMI FX (Only for DEH-X3700UI)

The illumination effect can be seen when;

– there is an incoming call – you are on a phone call – a CD is inserted/ejected The illumination effect will activate when the ACC power is turned on/off regardless of this setting.

(Only for DEH-X3700UI) Menu Item

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

Select the length of the playback time.

[KEY/DISPLAY], [KEY], [OFF]

Select the area for the illumination effect.

When [OFF] is selected, the color set under the ILLUMINATION settings (page 11) is used as the display color.

[SOUND LEVEL 1] to [SOUND LEVEL Change the illumination effect according to 6] the sound and bass level. The flash pattern changes according to the sound level. [LOW PASS 1] to [LOW PASS 6]

The flash pattern changes according to the bass level.

The flash pattern changes randomly according to the sound level mode and low pass mode.

The flash pattern changes randomly according to the sound level mode.

The flash pattern changes randomly according to the low pass mode.

Set the MIXTRAX special effects on/off.

Turn the MIXTRAX sound effects on/off while manually changing the tracks.

Connections/Installation

• Use of this unit in conditions other than the following could result in fire or malfunction.

– Vehicles with a 12-volt battery and negative grounding. – Speakers with 50 W (output value) and 4 Ω to 8 Ω (impedance value). • To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below. – Disconnect the negative terminal of the battery before installation. – Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring. – Place all cables away from moving parts, such as the shift lever and seat rails. – Place all cables away from hot places, such as near the heater outlet. – Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment. – Cover any disconnected cable connectors with insulating tape. – Do not shorten any cables.

Depending on the kind of vehicle, the function of and may be different. In this case, be sure to connect to and to . Yellow Back-up (or accessory) Yellow Connect to the constant 12 V supply terminal. Red Accessory (or back-up)

Connect to terminal controlled by the ignition switch (12 V DC). Connect leads of the same color to each other. Black (chassis ground) Blue/white The pin position of the ISO connector will differ depending on the type of vehicle. Connect and when Pin 5 is an antenna control type. In another type of vehicle, never connect and . Blue/white Connect to the system control terminal of the power amp (max. 300 mA 12 V DC). Blue/white Connect to the auto-antenna relay control terminal (max. 300 mA 12 V DC). Yellow/black If you use equipment with a Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. Speaker leads White: Front left White/black: Front left Gray: Front right Gray/black: Front right Green: Rear left or subwoofer Green/black: Rear left or subwoofer

• When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

– Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited.

– Use a fuse of the rating prescribed. – Never wire the negative speaker cable directly to ground. – Never band together negative cables of multiple speakers. • When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. • Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction. • The black cable is ground. Ground cables for this unit and other equipment (especially, high-current products such as power amps) must be wired separately. If they are not, an accidental detachment may result in a fire or malfunction.

AUX2 input jack (3.5 mm stereo jack)

(DEH-X3700UI only) A dedicated input jack designed exclusively for use with devices equipped with a mute function. Rear output or subwoofer output Front output Antenna input Fuse (10 A) Wired remote input Hard-wired remote control adapter can be connected (sold separately).

Violet: Rear right or subwoofer

Violet/black: Rear right or subwoofer Orange/white Connect to a car’s illumination signal. ISO connector In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors.

• Change the initial menu of this unit. Refer to [SP-P/O MODE] (page 5). The subwoofer output of this unit is monaural. • When using a subwoofer of 70 W (2 Ω), be sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/black leads.

Power amp (sold separately)

Perform these connections when using the optional amplifier.

• Do not install this unit where:

– it may interfere with operation of the vehicle. – it may cause injury to a passenger as a result of a sudden stop. • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. • Optimum performance is obtained when the unit is installed at an angle of less than 60°. • When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

Secure the mounting sleeve by using a screwdriver to bend the metal tabs

3 Dashboard Mounting sleeve • Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions.

System remote control

Connect to blue/white cable. Power amp (sold separately) Connect with RCA cables (sold separately) To front output Front speaker To rear output or subwoofer output Rear speaker or subwoofer

Determine the appropriate position where the holes on the bracket and the side of the unit match.

Tighten two screws on each side.

DIN front/rear mount

This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when installing.

Important • Check all connections and systems before final installation. • Do not use unauthorized parts as this may cause malfunctions. • Consult your dealer if installation requires drilling of holes or other modifications to the vehicle.

Insert the mounting sleeve into the dashboard.

For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle.

Tapping screw (5 mm × 8 mm)

Mounting bracket Dashboard or console

Remove the trim ring.

Notched tab • Releasing the front panel allows easier access to the trim ring. • When reattaching the trim ring, point the side with the notched tab down. Insert the supplied extraction keys into both sides of the unit until they click into place. Pull the unit out of the dashboard.

Additional Information

The repeat play range changes unexpectedly.

→ Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing. – Select the repeat play range again. A subfolder is not played back. → Subfolders cannot be played when [FLD] (folder repeat) is selected. – Select another repeat play range. The sound is intermittent. → You are using a device, such as a cellular phone, that may cause audible interference. – Move electrical devices that may be causing the interference away from the unit.

Common AMP ERROR → This unit fails to operate or the speaker connection is incorrect. → The protective circuit is activated. – Check the speaker connection. – Turn the ignition switch OFF and back to ON again. If the message remains, contact your dealer or an authorized Pioneer Service Station for assistance.

ERROR-07, 11, 12, 17, 30 → The disc is dirty. – Clean the disc. → The disc is scratched. – Replace the disc. ERROR-07, 10, 11, 12, 15, 17, 30, A0 → There is an electrical or mechanical error. – Turn the ignition switch OFF and back to ON, or switch to a different source, then back to the CD player. ERROR-15 → The inserted disc is blank. – Replace the disc. ERROR-23 → Unsupported CD format. – Replace the disc. FORMAT READ → Sometimes there is a delay between the start of playback and when you start to hear any sound. – Wait until the message disappears and you hear sound. NO AUDIO → The inserted disc does not contain any playable files. – Replace the disc. SKIPPED → The inserted disc contains DRM protected files. – The protected files are skipped.

FORMAT READ → Sometimes there is a delay between the start of playback and when you start to hear any sound. – Wait until the message disappears and you hear sound. NO AUDIO → There are no songs. – Transfer the audio files to the USB device and connect. → The connected USB device has security enabled. – Follow the USB device instructions to disable the security. SKIPPED → The connected USB device contains DRM protected files. – The protected files are skipped. PROTECT → All the files on the connected USB device are embedded with DRM. – Replace the USB device. N/A USB → The connected USB device is not supported by this unit. – Disconnect your device and replace it with a compatible USB device. CHECK USB → The USB connector or USB cable has short-circuited. – Check that the USB connector or USB cable is not caught in something or damaged.

→ The connected USB device consumes more than maximum allowable current.

– Disconnect the USB device and do not use it. Turn the ignition switch OFF and back to ACC or ON. Connect only compliant USB devices. → The iPod operates correctly but does not charge. – Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back to ON, or disconnect the iPod and reconnect.

The display automatically returns to the normal display.

→ No operations have been made for about 30 seconds. – Perform an operation.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information. – Switch the display or play another track/file.

→ All the files on the inserted disc are embedded with DRM. – Replace the disc.

→ Communication failed. – Perform one of the following operations, then return to the USB source. • Turn the ignition switch OFF and back to ON. • Disconnect the USB device. • Change to a different source. → iPod failure. – Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it. ERROR-23 → USB device was not formatted properly. – Format the USB device with FAT12, FAT16 or FAT32. ERROR-16 → The iPod firmware version is old. – Update the iPod version. → iPod failure. – Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it. STOP → There are no songs in the current list. – Select a list that contains songs.

→ No related songs. – Transfer songs to the iPod.

START UP APP → The application has not started running yet. – Operate the mobile device to start up the application.

Discs and player • Use only discs that feature either of the following two logos.

• Use only conventional, fully circular discs. • The following types of discs cannot be used with this unit: – DualDiscs – 8-cm discs: Attempts to use such discs with an adaptor may cause the unit to malfunction. – Oddly shaped discs – Discs other than CDs – Damaged discs, including discs that are cracked, chipped or warped – CD-R/RW discs that have not been finalized • Do not write on or apply chemicals to the surface of the discs. • To clean a CD, wipe the disc with a soft cloth outward from the center. • Condensation may temporarily impair the player’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth.

• When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment.

• Do not attach commercially available labels or other materials to the discs. – The discs may warp making the disc unplayable. – The labels may come off during playback and prevent ejection of the discs, which may result in damage to the equipment.

• Connections via USB hubs are not supported. • Firmly secure the USB storage device before driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal. • Depending on the USB storage device, the following problems may occur. – Operations may vary. – The storage device may not be recognized. – Files may not be played back properly. – The device may cause audible interference when you are listening to the radio.

• Do not leave the iPod in places with high temperatures. • Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal. • The settings of the iPod such as the equalizer and repeat play are changed automatically when the iPod is connected to the unit. Once the iPod is disconnected, those settings will return to the original settings.

• Incompatible text saved on the iPod will not be displayed by the unit.

Compressed audio compatibility

Audio Professional, Lossless, Voice/DRM Stream/Stream with video

• Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name. • The unit may not work properly depending on the application used to encode WMA files. • There may be a slight delay at the start of the playback of audio files embedded with image data, or audio files stored on a USB device with numerous folder hierarchies. • Russian text to be displayed on this unit should be encoded in one of the following character sets: – Unicode (UTF-8, UTF-16) – A character set other than Unicode that is used in a Windows environment and is set to Russian in the multi-language setting

• Pioneer cannot guarantee compatibility with all USB mass storage devices, and assumes no responsibility for any loss of data on media players, smartphones, or other devices while using this product. • Do not leave discs or a USB storage device in any place that is subject to high temperatures.

File extension Bit rate

48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR) 32 kHz, 44.1 kHz, 48 kHz

Bit rate Sampling frequency

MP3i (MP3 interactive), mp3 PRO

8 kbps to 320 kbps (CBR), VBR 8 kHz to 48 kHz (32 kHz, 44.1 kHz, 48 kHz for emphasis) 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1.x.) Not compatible Not compatible

• WAV file formats cannot be connected via MTP. File extension Quantization bits Sampling frequency

8 and 16 (LPCM), 4 (MSADPCM) 16 kHz to 48 kHz (LPCM), 22.05 kHz and 44.1 kHz (MS ADPCM)

FLAC files (DEH-2700UI only)

• FLAC file formats cannot be connected via MTP. • FLAC files may not be playable, depending on the encoder. File extension Sampling frequency Quantization bit rate Channel mode

• Regardless of the length of the blank section between the songs from the original recording, compressed audio discs play with a short pause between songs.

Playable files File system Multi-session playback Packet write data transfer

Up to eight tiers (A practical hierarchy is less than two tiers.)

Up to 99 Up to 999 ISO 9660 Level 1 and 2, Romeo, Joliet Compatible Not compatible

• There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies. Playable folder hierarchy

Up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders Up to 500 Playable files Up to 15 000 Playback of copyright- Not compatible protected files Partitioned USB Only the first partition device can be played.

This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported. Made for

• Operations may vary depending on the generation and/or software version of the iPod.

• Users of iPod with the Lightning Connector should use the Lightning to USB Cable (supplied with iPod). • Users of iPod with the Dock Connector should use the CD-IU51. For details, consult your dealer. • Refer to the iPod manuals for information about the file/format compatibility. • Audiobook, Podcast: Compatible

Example of a hierarchy

Folder Compressed audio file

01 to 05: Folder number to : Playback sequence

Russian character chart

CAUTION Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used.

Sequence of audio files

The user cannot assign folder numbers and specify playback sequences with this unit. Sequence of audio file depends on the connected device. Note that the hidden files in a USB device cannot be played back.

Copyright and trademark iTunes

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. WMA Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

Playable folder hierarchy

FLAC Copyright © 2000-2009 Josh Coalson

Copyright © 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: – Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. – Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. – Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

D: Display C: Character

– iPod touch (1st through 5th generation)

– iPod classic – iPod with video – iPod nano (1st through 7th generation)

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. iPod & iPhone iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Android™ Android is a trademark of Google Inc. MIXTRAX MIXTRAX is a trademark of the PIONEER CORPORATION.

General Power source: 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system: Negative type Maximum current consumption: 10.0 A Dimensions (W × H × D): DIN Chassis: 178 mm × 50 mm × 165 mm Nose: 188 mm × 58 mm × 17 mm D Chassis: 178 mm × 50 mm × 165 mm Nose: 170 mm × 46 mm × 17 mm Weight: 1 kg

Maximum power output: 50 W × 4 70 W × 1/2 Ω (for subwoofer) Continuous power output: 22 W × 4 (50 Hz to 15 000 Hz, 5 % THD, 4 Ω load, both channels driven) Load impedance: 4 Ω (4 Ω to 8 Ω allowable) Preout maximum output level: 2.0 V Loudness contour: +10 dB (100 Hz), +6.5 dB (10 kHz) (volume: –30 dB) Equalizer (5-Band Graphic Equalizer): Frequency: 80 Hz/250 Hz/800 Hz/2.5 kHz/8 kHz Equalization range: ±12 dB (2 dB step) Subwoofer (mono): Frequency: 50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 Hz Slope: –12 dB/oct, –24 dB/oct Gain: +6 dB to –24 dB Phase: Normal/Reverse

System: Compact disc audio system Usable discs: Compact disc Signal-to-noise ratio: 94 dB (1 kHz) (IEC-A network) Number of channels: 2 (stereo)

MP3 decoding format: MPEG-1 & 2 Audio

Layer 3 WMA decoding format: Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format: Linear PCM & MS ADPCM (Non-compressed)

USB USB standard specification: USB 2.0 full speed

Maximum current supply: 1 A USB Class: MSC (Mass Storage Class) File system: FAT12, FAT16, FAT32 MP3 decoding format: MPEG-1 & 2 Audio Layer 3 WMA decoding format: Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) FLAC decoding format: v1.3.0 (Free Lossless Audio Codec) (DEH-2700UI) WAV signal format: Linear PCM & MS ADPCM (Non-compressed)

Frequency range: 87.5 MHz to 108.0 MHz Usable sensitivity: 11 dBf (1.0 μV/75 Ω, mono, S/N: 30 dB) Signal-to-noise ratio: 72 dB (IEC-A network)

Frequency range: 531 kHz to 1 602 kHz Usable sensitivity: 25 μV (S/N: 20 dB) Signal-to-noise ratio: 62 dB (IEC-A network)

Frequency range: 153 kHz to 281 kHz Usable sensitivity: 28 μV (S/N: 20 dB) Signal-to-noise ratio: 62 dB (IEC-A network)

NOTE Specifications and the design are subject to modifications without notice.

[TALK], [STANDARD], [MUSIC]

[FASTER], [NORMAL], [SLOWER]

FM : [OFF], [LV1], [LV2], [LV3],

[LV4] MW/LW : [OFF], [LV1], [LV2]

[OFF], [LOW], [MID], [HI]

[SYNC ILLUMI]*, [SYNC CLOCK], [MANUAL]

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

[KEY/DISPLAY], [KEY], [OFF]

[LOW PASS 1] à [LOW PASS 6]

Sans position ACC SYSTEM RESET

[TALK], [STANDARD], [MUSIC]

[FASTER], [NORMAL], [SLOWER]

[OFF], [LOW], [MID], [HI]

INFO DISPLAY (solo per DEH-X3700UI)

[1.0 MIN], [1.5 MIN], [2.0 MIN],

[2.5 MIN], [3.0 MIN], [OFF] [KEY/DISPLAY], [KEY], [OFF]

FLASH PATTERN Da [SOUND LEVEL 1] a [SOUND LEVEL 6]

Da [LOW PASS 1] a [LOW PASS 6]

[SYNC ILLUMI]*, [SYNC CLOCK], [MANUAL]

SHORT PLAYBCK DISPLAY FX

8 e 16 (LPCM), 4 (MSADPCM) Da 16 kHz a 48 kHz (LPCM), 22,05 kHz e 44,1 kHz (MS ADPCM)

Dimensioni (L × A × P):

DIN Telaio: 178 mm × 50 mm × 165 mm Testata: 188 mm × 58 mm × 17 mm D Telaio: 178 mm × 50 mm × 165 mm Testata: 170 mm × 46 mm × 17 mm Peso: 1 kg

PRODUCTO LASER CLASE 1

[TALK], [STANDARD], [MUSIC]

[FASTER], [NORMAL], [SLOWER]

[OFF], [LOW], [MID], [HI]

LANGUAGE AUX DIM SETTING

[SYNC ILLUMI]*, [SYNC CLOCK], [MANUAL]

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

[KEY/DISPLAY], [KEY], [OFF]

FLASH PATTERN De [SOUND LEVEL 1] a [SOUND LEVEL 6]

De [LOW PASS 1] a [LOW PASS 6]

48 kHz No compatible

SP-P/O MODE [REAR/SUB.W] [SUB.W/SUB.W]

[TALK], [STANDARD], [MUSIC]

[OFF], [LOW], [MID], [HI]

[FASTER], [NORMAL], [SLOWER]

[SYNC ILLUMI]*, [SYNC CLOCK],

Displayhelligkeit ändern.

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

[KEY/DISPLAY], [KEY], [OFF]

DEH-X3700UI M.C. (multi-control)-knop

SRC (bron)/OFF Display

Best stations memory (BSM)

[TALK], [STANDARD], [MUSIC]

[FASTER], [NORMAL], [SLOWER]

[OFF], [LOW], [MID], [HI]

[KEY COLOUR], [DISP COLOUR],

[SYNC ILLUMI]*, [SYNC CLOCK], [MANUAL]

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

[KEY/DISPLAY], [KEY], [OFF]

[LOW PASS 1] tot [LOW PASS 6]

Tappende schroef (5 mm × 8 mm)

Montagebeugel Dashboard of console

Audio Professional, Lossless, Voice/DRM Stream/Stream met video

Bemonsteringsfreque ntie

(Английский), [РУС] (Русский), [TUR] (Турецкий)

[TALK], [STANDARD], [MUSIC]

[FASTER], [NORMAL], [SLOWER]

[KEY COLOUR], [DISP COLOUR],

[1.0 MIN], [1.5 MIN], [2.0 MIN], [2.5 MIN], [3.0 MIN], [OFF]

[KEY/DISPLAY], [KEY], [OFF]