ES-ST3N-S803 - Rasoir électrique PANASONIC - Free user manual and instructions

USER MANUAL ES-ST3N-S803 PANASONIC

Operating Instructions Rechargeable Shaver Model No. ES‑ST25

GB D F I NL E Operating Instructions

Rechargeable Shaver Model No. ES-ST25

GUARANTEE Personal Care Products

GB D F E NL I Operating Instructions

(Household) Rechargeable Shaver Model No. ES‑ST25

Parts identification10

For environmental protection and recycling of materials19

TR Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. • The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped. • This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower. 6

GB This shaver has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment.

- Doing so may cause overheating, ignition, or explosion.

I Explanation of symbols

DANGER D To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions.

F Safety precautions

The following symbols are used to classify and describe the type of instructions to be observed.

N P DK E NL Regularly clean the power plug, the appliance plug and the side terminals to prevent dust from accumulating.

- Failure to do so may cause fire due to insulation failure caused by humidity. Disconnect the adaptor and wipe with a dry cloth.

S CAUTION Denotes a hazard that could result in minor injury.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor.

Fully insert the adaptor or appliance plug. - Failure to do so may cause fire, electric shock, or burn.

FIN WARNING Denotes a potential hazard that could result in serious injury or death.

PL Denotes a potential hazard that will result in serious injury or death.

CZ DANGER WARNING Always unplug the adaptor from a household outlet when cleaning.

- Failure to do so may cause electric shock or injury.

SK This symbol is used to alert users to a specific operating procedure that must not be performed.

RO H This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

TR The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

WARNING Immediately stop using and remove the adaptor if there is an abnormality or failure.

- Using it in such conditions may cause fire, electric shock, or injury. <Abnormality or failure cases> ••The main unit, adaptor, or power cord is deformed or abnormally hot. ••The main unit, adaptor, or power cord smells of burning. ••There is abnormal sound during use or charging of the main unit, adaptor, or power cord. - Immediately request inspection or repair at an authorized service center. If the oil is consumed accidentally, do not induce vomiting, drink a large amount of water, and contact a physician. If the oil comes into contact with eyes, immediately wash thoroughly with running water, and contact a physician. - Failure to do so may result in physical problems. Do not connect or disconnect the adaptor to a household outlet with a wet hand. - Doing so may cause electric shock or injury. Do not immerse the AC adaptor and the charging stand in water or wash with water. - Doing so may cause electric shock or fire due to a short circuit.

Never use the AC adaptor and the charging stand in the bathroom or shower room.

- Doing so may cause electric shock or fire due to a short circuit. Do not use anything other than the supplied AC adaptor and the charging stand. Also, do not charge any other product with the supplied AC adaptor and the charging stand. - Doing so may cause burn or fire due to shorting. Never use the appliance if the AC adaptor is damaged or if the plug fits loosely in a household outlet. - Doing so may cause electric shock or fire due to a short circuit. Do not damage, break, modify, or forcibly bend, pull, or twist the power cord. Also, do not place anything heavy on or pinch the power cord. - Doing so may cause electric shock or fire due to a short circuit. Do not use in a way exceeding the rating of the household outlet or the wiring. - Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating. Do not modify or repair. - Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (battery change, etc.). Do not store within the reach of children or infants. Do not let them use it. - Putting the inner blades and/or the cleaning brush in the mouth or drinking the oil may cause accidents and injury.

Do not allow pins or trash to adhere to the power plug, the appliance plug or the side terminals.

- Doing so may cause electric shock or fire due to a short circuit.

GB D F I NL E DK P N S FIN Do not drop or subject to shock.

- Doing so may cause injury. Do not wrap the power cord around the Adaptor or the charging stand when storing. - Doing so may cause the wire in the power cord to break with the load, and may cause fire due to shorting.

PL Disconnect the adaptor or the appliance plug by holding onto them instead of the power cord.

- Disconnecting by holding onto the power cord may cause electric shock or injury.

Do not share your shaver with your family or other people.

- Doing so may result in infection or inflammation.

CZ Be sure to place the shaver in its carrying holder when carrying around or storing.

- Failure to do so may cause injury to skin or reduce the life of the system outer foil.

Do not use this product for hair on head or any other part of the body.

- Doing so may cause injury to skin or reduce the life of the system outer foil.

SK Check the system outer foil for cracks or deformations before use.

- Cracks or deformations of the system outer foil may result in injury to the skin.

Do not touch the blade section (metallic section) of the inner blade.

- Doing so may cause injury to your hands.

H CAUTION Disconnect the adaptor from the household outlet when not charging.

- Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Do not forcefully press the blades. Also, do not touch the system outer foil with fingers or nails when in use.

- Doing so may cause injury to skin or reduce the life of the system outer foil.

RO Never disassemble except when disposing of the product.

- Doing so may cause fire, electric shock, or injury.

Do not use excessive pressure to apply the outer foil to your lip or other part of your face. Do not apply the outer foil directly to blemishes or injured skin.

- Doing so may cause injury to the skin.

TR WARNING Intended use

••Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method. ••Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged. ••If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time. ••Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals. ••Store the shaver in a place with low humidity after use. ••Do not store the shaver where it will be exposed to direct sunlight or other heat sources.

Parts identification

A Main body 1 System outer foil 2 Foil frame 3 Foil frame release buttons 4 Cleaning shutter 5 Finger rest 6 Side terminals 7 Power switch 8 Shaving sensor lamp ( ) 9 Charge status lamp ( ) : Inner blades ; Trimmer  Trimmer handle  Outer foil section  System outer foil release buttons  Water inlet

B AC adaptor (RE7‑59)

 Adaptor  Power plug  Power cord  Appliance plug C Charging stand (RC9‑83)  Charging terminals  Stand socket D Carrying holder Accessories E Cleaning brush F Oil  Operating Instructions  Guarantee Card

the appliance plug [B]

1 Insert into the stand socket [C].

1 the shaver in the charging stand [C] as

2 Insert illustrated.

••The shaver will not charge unless the side terminals

(a) are in contact with the charging terminals (b). ••Wipe off any water droplets on the side terminals.

► the carrying holder Attach the carrying holder as illustrated. ••Securely attach the carrying holder to the main unit.

in the adaptor [B] into a household

••Check that the charge status lamp glows.

••Charging is completed after approx. 1 hour. The charging time may decrease depending on the charging capacity.

► the carrying holder Remove the carrying holder while pressing down on both sides.

D You can charge the shaver with the carrying holder attached.

► the carrying holder The shaver can be kept vertically or horizontally. When transporting the shaver, you can use the carrying holder to protect the outer foil and prevent erroneous operation of the switch. ••When transporting the shaver, be sure to clean off any shavings before attaching the carrying holder.

The charge status lamp ( ) glows red.

After charging is completed

The charge status lamp ( ) turns off.

The charge status lamp ( ) will blink twice every second.

••After charging is completed, turning the power switch ON with the shaver plugged in will cause charge status lamp to light up and then turn off after 5 seconds.

This shows that the shaver is fully charged. ••Recommended ambient temperature for charging is 10 – 35 °C. It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures. The charge status lamp ( ) will blink twice every second when there is a problem with charging. Charge the shaver within the recommended ambient temperature range. ••When charging the shaver for the first time or when it has not been in use for more than 6 months, the charge status lamp ( ) may not glow. It will eventually glow if kept connected.

Using the shaver the power switch [A7] to select the

1 Press desired shaving mode.

••Each time you press the power switch, the shaving mode changes from “Shaving sensor mode” “Normal mode” “OFF.”

Shaving sensor Normal mode mode Beard thickness is automatically The power level is sensed and the constantly power is maintained while automatically shaving. adjusted when shaving.

the adaptor [B] after charging is

4 Disconnect completed.

••Charging the battery for more than 1 hour will not affect battery performance.

You cannot operate the shaver while charging.

The shaving sensor lamp ( ) glows blue.

The shaving sensor lamp ( ) turns off.

The shaving sensor lamp ( ) turns off.

GB D F E NL I The charge status lamp ( ) blinks once every second when operating the shaver.

••You can shave 2 to 3 times after the charge status lamp ( ) blinks. (This will differ depending on usage.)

••A full charge will supply enough power for approx. 14 shaves of 3 minutes each. ••If the shaver is operated in the shaving sensor mode in a battery‑shortage condition, the shaving sensor lamp ( ) glows blue, and the charge status lamp ( ) blinks red.

S You can also use a pen grip to hold the shaver.

When the battery capacity is low

••Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

Reading lamps when using

the shaver as illustrated

••We recommend using the shaver in an ambient temperature range of 5 – 35 °C. If used outside this range, the appliance may stop operating.

••The shaving sensor may not respond depending on the thickness of the beard or the type of the shaving gel, but this is normal.

► the trimmer Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns.

► ••Before shaving, check that the cleaning shutter is closed. ••Place your finger on the finger rest while in use. Keeping your finger placed on the power switch during use may switch the mode or turn the shaver OFF. ••Do not use shaving creams or face cleansers containing scrubbing compounds as these may cause the outer foil to clog.

1. Remove the shaver from the charging stand [C]. 2. Apply some hand soap and some water to the outer foil. ••Close the cleaning shutter. 3. Turn the shaver on.

There are two ways to clean the shaver, depending on the actual dirt level.

4. Slide the cleaning shutter

[A4] until it clicks.

4. Turn the shaver off after

10 – 20 seconds. 5. Remove the outer foil section [A] and turn the shaver on.

5. Clean the outer foil section [A] with running water.

6. Clean the shaver and the outer foil section [A] with running water.

6. Turn the shaver off. ••Rinse with water and shake up and down several times to remove the water.

••Rinse with water and shake up and down several times to remove the water.

••Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction.

To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used.

1. Switch off the shaver.

2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds.

► with the short brush Clean the inner blades [A] using the short brush by moving it in direction (A). ••Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness. ••Do not use the short brush to clean the outer foils.

5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth.

► with the long brush Clean the system outer foil  (a), the shaver body (b) and the trimmer (c) using the long brush.

GB Cleaning with the brush

7. Wipe off any drops of water with a dry cloth.

8. Dry the outer foil section [A] and the shaver completely in a shaded area. ••The outer foil section will dry faster if removed from the main body. 9. Attach the outer foil section [A] to the shaver. 10.Lubricate the shaver. (See this page.)

Replacing the system outer foil and the inner blades system outer foil

once every two years

► the outer foil section Press the foil frame release buttons [A3] and lift the outer foil section [A] upwards.

► the inner blades 1. Remove the inner blades [A] one at a time. ••Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 2. Insert the inner blades [A] one at a time until they click.

►Attaching ► the outer foil section After turning the water inlet surface to the front, securely attach the outer foil section [A] to the shaver until it clicks. ►Replacing ► the system outer foil 1. Press the system outer foil release buttons [A] and pull down the system outer foil. 2. Align the water inlet surface and the system outer foil mark ( ) and securely attach together. ••The system outer foil cannot be reversely attached. ••Always insert the system outer foil to the foil frame when attaching to the shaver.

Trimmed hairs fly all over.

This can be improved by cleaning every time after shaving.

Clean the inner blades with the brush.

Apply oil after cleaning with water and leaving to dry thoroughly. Confirm that the cleaning shutter is firmly closed.

(See page 15.) System outer foil gets hot.

Replace the system outer foil if it is damaged or deformed.

You do not get as close a shave as before.

Replace the system outer foil and/or inner blades.

Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years

The shaving sensor responds even though the shaver is not in contact with the skin.

DK E NL I F D GB Replace the system outer foil and/or inner blades.

Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years

P Clean the beard trimmings from the shaver.

When the shaver is extremely dirty, remove the foil frame and wash with water. (See page 14.)

PL This can be improved by cleaning every time after shaving.

N Apply oil. The shaving sensor may not respond when there is not enough oil on the blades.

This can be improved by cleaning every time after shaving.

S The blades can be dried more easily by removing for drying.

The shaving sensor may not respond depending on the thickness of the beard or the type of the shaving gel, but this is normal.

FIN The shaving sensor does not respond.

SK The odor is getting stronger.

Depending on the beard thickness, the shaving sensor may not react and the driving sound may not change. This is not abnormal.

H The blades do not dry.

The blades may not dry quickly due to temperature conditions.

RO The shaver cannot be properly cleaned even after water is poured from the water inlet.

When the shaver is very dirty, first use the cleaning brush to remove beard trimmings. Or, remove the foil frame and wash with water. (See page 14.)

Confirm that the blades are properly attached.

The driving sound changes while shaving.

The power will not switch to OFF.

Press the power switch twice while using in the shaving sensor mode.

Push the main body into the charging stand all the way and make sure the charge status lamp glows.

The shaver cannot be charged.

Operating time is short even after charging.

The shaver can be loud due to the linear motor. This does not indicate a problem.

While the shaving sensor lamp glows, the shaving sensor is operating. The sound changes depending on the beard thickness.

Gently wipe the side terminals and the charging terminals of the charging stand with a cloth or tissue damped with water.

The recommended temperature for charging is 10 – 35 °C. If charged at a temperature other than the recommended temperature, the shaver may take longer to charge or may not charge at all.

Shaver stopped functioning.

When the number of operations per charge starts to decrease, the battery is nearing the end of its life.

Recommended ambient temperature for operation is 5 – 35 °C. The shaver may stop functioning when out of recommended ambient temperature range. The battery has reached the end of its life.

Contact Please visit Panasonic web site http://panasonic.net or contact an authorized service center (you find its contact address in the pan european guarantee leaflet.) if you need information or if the shaver or the cord gets damaged.

GB D N P DK E NL I F

S The life of the battery is 3 years if charged approximately once every two weeks. The battery in this shaver is not intended to be replaced by consumers. Have the battery replaced by an authorized service center.

Information for Users on Collection and Disposal of Old

Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

This shaver contains a Lithium‑ion battery.

Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country.

H System outer foil and

Replacement parts for inner blades System outer foil ES‑ST25

RO Replacement parts are available at your dealer or Service

For environmental protection and recycling of materials

TR Replacement parts

Disposal of the built-in rechargeable battery

Remove the built-in rechargeable battery before disposing of the shaver. Please make sure that the battery is disposed of at an officially designated location if there is one. This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction. ••Remove the shaver from the charging stand. ••Press the power switch to turn on the power and then keep the power on until the battery is completely discharged. ••Perform steps 1 to 6 and lift the battery, and then remove it. ••Please take care not to short-circuit the battery.  

See the name plate on the AC adaptor.

(Automatic voltage conversion)

In shaving mode: 64 (dB (A) re 1 pW)

In trimmer mode: 66 (dB (A) re 1 pW)

This product is intended for household use only.

GB D F E NL I GB D F I NL E TR RO H SK CZ PL FIN S N P DK GB D F I NL E DK P N S FIN D F I NL E DK P N GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S FIN PL CZ GB D F I NL E DK P GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S FIN PL CZ SK GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S FIN PL CZ SK GB D F E DK P N S CZ PL

FIN GB D F I NL E DK P N S For at fjerne let snavs

under barbering: 64 (dB (A) re 1 pW) under trimning: 66 (dB (A) re 1 pW)

GB D F I NL E TR RO H SK CZ PL FIN S N P DK GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S

3 ••Kontroller at lampen for ladestatus lyser.

Sensorlampen for barbering ( ) slukkes.

Sensorlampen for barbering ( ) slukkes.

Lampen for ladestatus ( ) blinker én gang hvert sekund under barbering.

Lyden endres under barbering.

D F I NL E DK P N WES9068

FIN Reservedeler for

H Under barbering: 64 (dB (A) re 1 pW)

Under trimming: 66 (dB (A) re 1 pW)

GB D F I NL E DK P I NL E DK P N S Akun kesto

SK GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S FIN PL CZ GB D F I NL E DK GB D F I NL E DK P GB D F I NL E DK P N S FIN GB D F I NL E DK P N FIN S

PL GB D F I NL E DK P N S FIN PL GB D F I NL E DK P N S FIN PL CZ SK GB D F I NL E DK P N NL E DK P N S FIN

GB D F I NL E DK P GB D F I NL E DK P N S FIN GB D F I NL E DK P N Lame interioare

S GB D F I NL E DK GB D F I NL E DK P GB D F I NL E DK P N S F EN, GE, FR, IT, DU, SP, DA, PT, NW, SW, FI, PL, CZ, SK, HU, RO, TK Printed in Japan

ES9700ST251E Y0413-0