STRIKE 4 - Chauvet Professional - Free user manual and instructions

Product Type	LED Wash Light / Audience Blinder
Model	STRIKE 4
Brand	Chauvet Professional
DMX Personalities	1, 3, 4, or 9-channel
Light Source	4 x 100W white COB LEDs
LED Lifespan	50,000 hours
Illuminance @ 5 m	999 lux total / 242 lux per cell
Beam Angle	49°
Field Angle	79°
Dimming	16-bit smooth dimming with selectable dimmer curves
Strobe	0–20 Hz with random strobe macros
Control Options	DMX, Master/Slave, Static mode, Auto programs
Display	OLED display with menu buttons
PWM Frequency	Adjustable: 600 Hz, 1200 Hz, 2000 Hz, 4000 Hz, 25 kHz
Power Supply Type	Switching (internal), auto-ranging
Input Voltage	100–240 VAC, 50/60 Hz
Power Consumption	301 W @ 120 VAC / 286 W @ 230 VAC
Power Linking	Up to 5 @ 120 V, 9 @ 208 V, 10 @ 230 V
Fuse	T 5 A, 250 V (replaceable)
Dimensions (L x W x H)	14.2 x 6.4 x 14.2 in (362 x 163 x 362 mm)
Weight	19 lb (8.7 kg)
IP Rating	IP20 (indoor use only)
Max Ambient Temperature	113°F (45°C)
Cooling System	Fan-assisted convection
Mounting	Yoke with safety cable; mounting clamps required
Maintenance	Clean at least twice a month using vacuum/compressed air and mild cleaner

Frequently Asked Questions - STRIKE 4 Chauvet Professional

How do I set the DMX address on the STRIKE 4?

Go to the DMX Address menu on the control panel and select 001–512. The highest usable address depends on the DMX personality (for example, up to 504 in 9-channel mode).

Can the STRIKE 4 be linked to other fixtures for master/slave operation?

Yes, set one unit as Master and the others as Slave in the Master/Slave Mode menu. The slaves will mirror the master's auto programs or static settings. Do not connect a DMX controller in this mode.

What is the recommended cleaning procedure?

Disconnect power and wait for the product to cool. Use a vacuum or dry compressed air to remove dust from vents, and clean surfaces with a mild solution of non-ammonia glass cleaner applied to a soft cloth. Do not spin fans while blowing air.

What is the maximum number of STRIKE 4 units that can be power-linked?

Up to 5 units at 120 VAC, up to 9 at 208 VAC, and up to 10 at 230 VAC. Always use approved power linking cables.

How do I replace the fuse?

Disconnect the power cord, unscrew the fuse holder cap, replace the blown fuse with a T 5 A, 250 V fuse, and screw the cap back. Always use the same type and rating.

Does the STRIKE 4 have adjustable PWM to avoid flicker on camera?

Yes, you can change the LED frequency via the LED Frequency menu: 600 Hz, 1200 Hz, 2000 Hz, 4000 Hz, or 25 kHz. This helps eliminate flicker in film and studio applications.

What are the DMX channel functions for 9-channel mode?

Channels are: 1 Dimmer High, 2 Dimmer Low, 3 Strobe, 4–7 White pods 1–4, 8 Auto Programs, 9 Dimmer Speed. See the full DMX Values chart in the manual.

Is the STRIKE 4 suitable for outdoor use?

No, it has an IP20 rating and is for indoor use only. Avoid rain, moisture, and extreme temperature changes.

What is the maximum ambient temperature for operation?

The maximum ambient temperature is 113°F (45°C). Operate only below this limit to prevent overheating.

Can I control the tilt or pan of the individual LED pods?

The STRIKE 4 allows individual manual pan adjustment of each LED pod for directional placement, but there is no motorized or DMX-controlled positioning.

USER MANUAL STRIKE 4 Chauvet Professional

STRIKE 4

User Manual

Edition Notes	The STRIKE 4 User Manual Rev. 2 covers the description, safety precautions, installation, programming, operation, and maintenance of the STRIKE 4. Chauvet released this edition of the STRIKE 4 User Manual in June 2017.
Trademarks	CHAUVET, the Chauvet logo and STRIKE 4 are registered trademarks or trademarks of Chauvet & Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.
Copyright Notice	The works of authorship contained in this manual, including, but not limited to, all design, text and images are owned by Chauvet.© Copyright 2017 Chauvet & Sons, LLC. All rights reserved.Electronically published by Chauvet in the United States of America.
Manual Use	Chauvet authorizes its customers to download and print this manual for professional information purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this manual or its content for any other purpose without written consent from Chauvet.
Document Printing	For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended Audience	Any person in charge of installing, operating, and/or maintaining this product should completely read through the guide that shipped with the product, as well as this manual, before installing, operating, or maintaining this product.
Disclaimer	Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, Chauvet has no obligation to make, and does not commit to make, any such revisions..
Document Revision	The STRIKE 4 User Manual Rev. 2 supersedes all previous versions of this manual. Discard any older versions of this manual and replace with this version. Go to www.chauvetprofessional.com for the latest version.

Table of Contents

1. Before You Begin .... 1

What Is Included 1

Claims....1

Manual Conventions ...... 1

Symbols 1

Product At A Glance 2

Safety Notes 2

Personal Safety....2

Mounting And Rigging....2

Power And Wiring 2

Operation 2

Expected LED Lifespan 2

2. Introduction ......3

Description....3

Features....3

Overview 4

Dimensions 5

3. Setup....6

AC Power....6

AC Plug....6

Power Linking 6

Fuse Replacement....6

DMX Linking....7

DMX Personalities....7

Master/Slave Connectivity....7

Mounting 8

Orientation 8

Rigging....8

Procedure 8

4. Operation 9

Control Panel Description....9

Control Options 9

Programming......9

DMX Personality 9

DMX Control....9

Static Operation 10

Auto Programs....10

Auto Test....10

Master/Slave 10

Software Information....10

Temperature 10

Backlight 10

Dimmer Curves 11

Fixture Hours....11

LED Frequency 11

Fan Control 11

Menu Map 12

DMX Values....13

STRIKE 4 Pod Selection for DMX Control....14

STRIKE 4 Angle Adjustment for DMX Control....14

1. Technical Information ....15

Product Maintenance....15

1. Technical Specifications....16

Photometrics Chart 17

Returns 18

Contact Us....19

1. BEFORE YOU BEGIN

What Is Included

• STRIKE 4
- Neutrik powerCON power cord
- Warranty Card
- Quick Reference Guide

Claims

Carefully unpack the product immediately and check the box to make sure all the parts are in the package and are in good condition.

If the box or the contents (the product and included accessories) appear damaged from shipping or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection.

For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Manual Conventions

Convention	Meaning
1–512	A range of values in the text
50/60	A set of mutually exclusive values in the text
	A button on the product's control panel
Settings	A product function or a menu option
MENU>Settings	A sequence of menu options
1–10	A range of menu values from which to choose in a menu
Yes/No	A set of two mutually exclusive menu options in a menu
ON	A unique value to be entered or selected in a menu

Symbols

Symbols		Meaning
		Critical installation, configuration, or operation information. Failure to comply with this information may cause the product not to work, damage third-party equipment, or cause harm to the operator.
		Important installation or configuration information. Failure to comply with this information may keep the product from working.
		Useful information.

The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data transmission protocol.

Product At A Glance	Use on Dimmer	X	Auto Programs	P
	Outdoor Use	X	Auto-Ranging Power Supply	P
	Master/Slave	P	Replaceable Fuse	P
	DMX	P	User-Serviceable	X

Safety Notes

Personal Safety

Mounting And Rigging

Power And Wiring

Operation

Expected LED Lifespan

Read all the following Safety Notes before working with this product. These notes include important information about the installation, usage, and maintenance of this product.

This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained Chauvet certified technicians. Do not open the housing or attempt any repairs.

All applicable local codes and regulations apply to proper installation of this product.

• Avoid direct eye exposure to the light source while the product is on.
  • Always disconnect this product from its power source before servicing.
  • Always connect this product to a grounded circuit to avoid the risk of electrocution.
  Do not touch this product's housing during operation because it may be very hot.
• This product is for indoor use only! To prevent risk of fire or shock, do not expose this product to rain or moisture. (IP20)
• CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
  • Make sure there are no flammable materials close to this product while it is operating.
• When hanging this product, always secure to a fastening device using a safety cable.
• Always make sure you are connecting this product to the proper voltage in accordance with the specifications in this manual or on the product's specification label.
  • To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
• Never connect this product to a dimmer pack or rheostat.
• Never disconnect this product by pulling or tugging on the power cable.
• Do not operate this product if you see damage on the housing, lenses, or cables. Have the damaged parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a higher temperature.
  • In case of a serious operating problem, stop using this product immediately!

In the unlikely event that your Chauvet product may require service, contact Chauvet Technical Support.

LEDs gradually decline in brightness over time, mostly because of heat. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED conditions. For this reason, using clustered LEDs at their fullest intensity significantly reduces the LEDs' lifespan. Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If extending this lifespan is vital, lower the operating temperature by improving the ventilation around the product and reducing the ambient temperature to an optimal operating range. In addition, limiting the overall projection intensity may also help to extend the LEDs' lifespan.

2. INTRODUCTION

Description The STRIKE 4 features four independently focusable 100W chip-on-board LEDs that provide incredible output and coverage for a wide gamut of production genres. STRIKE 4 features smooth 16-bit dimming control for those incandescent-style fades, a series of automated strobe effects for using the STRIKE 4 as an audience blinder, individual manual pan control of each LED pod and adjustable PWM for using the STRIKE 4 in film and studio locations. STRIKE 4 comes standard with basic and advanced control personalities for flexibility in programming, and an easy-to-read OLED display for quick onboard adjustments.

Features

• 1-, 3-, 4-, or 9-channel LED wash product
- Operating modes:

• 1-channel: strobe
• 3-channel: intensity, duration, rate, effect, macro
• 4-channel: flash 1–8
- 9-channel: flash 1–8, auto programs, auto speed, dimmer, strobe

• 16-bit dimming control for smooth, perfect fades
- Individual pan of each head to allow for directional adjustment of light output
• Simple and complex DMX channel profiles for programming flexibility
- Easy to use OLED display
• Automated strobing programs for easy programming
- Adjustable Pulse Width Modulation (PWM) control to eliminate flicker on camera

Overview

Front View

Rear View

Top View

Side View

Dimensions

3. SETUP

AC Power

Each STRIKE 4 has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each STRIKE 4, refer to the label affixed to the product. You can also refer to the Technical Specifications chart in this manual.

The listed current rating indicates the maximum current draw during normal operation. For more information, you may download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.

• Always connect this product to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

AC Plug

The STRIKE 4 comes with a power input cord terminated with a Neutrik powerCON A connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with your product has no plug, or if you need to change the Edison plug, use the table below to wire the new plug.

Connection	Wire (U.S.)	Wire (Europe)	Screw Color
AC Live	Black	Brown	Yellow or Brass
AC Neutral	White	Blue	Silver
AC Ground	Green/Yellow	Green/Yellow	Green

Power Linking

The STRIKE 4 supports power linking. You can power link up to 5 products at 120 V; up to 9 at 208 V; or up to 10 at 230 V.

This product comes with a power input cord. Power linking cables are available from Chauvet for purchase.

Fuse Replacement

1. Disconnect this product from the power outlet.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating (T 5 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.

Make sure to disconnect the product's power cord before replacing a blown fuse. Always replace the blown fuse with another of the same type and rating.

DMX Linking

You can link the STRIKE 4 to a DMX controller using a 5-pin DMX connection. If using other DMX-compatible products with the STRIKE 4, you can control each individually with a single DMX controller.

DMX Personalities

The STRIKE 4 uses a 5-pin DMX data connection for the 1-, 3-, 4- and 9-channel DMX personalities.

• Refer to the Introduction chapter for a brief description of each DMX personality.
- Refer to the Operation chapter to learn how to configure the STRIKE 4 to work in these personalities.
- The DMX Values section provides you with detailed information regarding the DMX personalities.

If you are not familiar with or need more information about DMX standards, Master/Slave connectivity, or the DMX cables needed to link this product to a DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.

Master/Slave Connectivity

The Master/Slave mode allows a single STRIKE 4 (the “master”) to control the actions of one or more STRIKE 4 products (the “slaves”) without the need of a DMX controller to control the slaves. Once set and connected, the slaves will operate in unison with the master. For instructions on connecting and configuring this product, see Master/Slave Mode.

DO NOT connect a DMX controller to products operating in Master/Slave mode. The DMX controller signals may interfere with the signals from the master.

If you are not familiar with or need more information about DMX standards, or the DMX cables needed to link this product to a DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.

Mounting

Before mounting this product, read and follow the Safety Notes. For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.

Orientation

Always mount this product in a safe position and make sure there is adequate room for ventilation, configuration, and maintenance.

Rigging

Chauvet recommends using the following general guidelines when mounting this product.

• When selecting an installation location, consider easy access to this product for operation, programming adjustments, and routine maintenance.
  • Make sure to mount this product away from any flammable material as indicated in the Safety Notes.
• Never mount in places where rain, high humidity, extreme temperature changes, or restricted ventilation may affect the product.
• If hanging this product, make sure that the mounting location can support the product's weight. See the Technical Specifications for the weight-bearing requirements of this product.
• When hanging this product, always secure to a fastening device using a safety cable. For our CHAUVET Professional line of safety cables, go to http://trusst.com/products/.

Procedure

The STRIKE 4 comes with a 2 position yoke that allows you to attach mounting clamps for hanging. You must supply your own mounting clamps. Make sure the clamps are capable of supporting the weight of this product. Use at least one mounting point per product. For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.

Overhead Mounting

4. OPERATION

Control Panel Description

Button	Function
	Exits from the current menu or function
	Enables the currently displayed menu or sets the currently selected value in to the current function
	Navigates upward through the menu list or increases the numeric value when in a function
	Navigates downward through the menu list or decreases the numeric value when in a function

Control Options

You can set the STRIKE 4 starting address in the 001–512 DMX range. This enables control of up to 56 products in the 9-channel personality.

Programming

Refer to the Menu Map to understand the menu options. The menu map shows the main level and a variable number of programming levels for each option.

• To go to the desired main level, press repeatedly until the option shows on the display. Press to select. This will take you to the first programming level for that option.
• To select an option or value within the current programming level, press or until the option shows on the display. Press to select. In this case, if there is another programming level, you will see that first option, or you will see the selected value.
• Press repeatedly to exit to the previous main level.

DMX

This setting allows you to choose a particular DMX personality.

Personality

1. Go to the DMX Channel main level.
2. Select the desired personality (1 Ch, 3 Ch, 4 Ch, or 9 Ch).

- See the DMX Values section for the highest starting address you can select for each personality.

- Make sure that the starting addresses on the various products do not overlap due to the new personality setting.

DMX Control

In this mode, each product will respond to a unique starting address from the DMX controller. All products with the same starting address will respond in unison.

1. Select a DMX personality as shown in DMX Personality.
2. Go to the DMX Address main level.
3. Select the starting address (001-512).

The highest recommended starting address for each DMX mode is as follows:

DMX Mode	DMX Address
1 Ch	512
3 Ch	510
4 Ch	509
9 Ch	504

Static Operation

The Static mode allows the user to set the intensity and the strobe frequency from the control panel without a DMX controller.

1. Go to the Static main level.
2. Select Dimmer.
3. Choose desired intensity (000–255).
4. Select Strobe.
5. Select the desired strobe frequency (000–255).

Auto Programs

Auto programs allow for control of pre-programmed strobe looks without a DMX controller.

1. Go to the Auto Show main level.
2. Select the desired auto program (Auto 0–6).
3. Select Speed.
4. Choose the desired speed value (000–100).

You cannot edit any of the auto programs (Auto 0–6).

Auto Test

This option allows you to test all the LEDs on the STRIKE 4.

1. Go to Information main level.

2. Select Auto > Test.

Master/Slave

The Master/Slave mode allows a group of STRIKE 4s (the slaves) to simultaneously duplicate the output of another STRIKE 4 (the master) without a DMX controller.

1. Set each of the slaves:
   a. Go to the Master/Slave Mode main level.
   b. Select Slave.
2. Set the master product:
   a. Go to the Master/Slave Mode main level.
   b. Select Master.

c. Select an Auto program as explained in Auto Programs or Static program as explained in Static Operation.

- The master is the one that runs a program whether in Auto Show or Static mode.

- Do not connect a DMX controller to the products configured for Master/Slave operation. The DMX controller may interfere with signals from the master product.

The master should be the first product in the daisy chain.

Software Information

This option shows what version of software the STRIKE 4 is running.

1. Go to the Information main level.
2. Select Version and the version number will show on the screen.

Temperature

This option shows the internal temperature of each of the STRIKE 4's individual pods.

1. Go to the Temperature main level.
2. Select LED 1-4

Backlight

This setting allows you to set the amount of time the backlight on the STRIKE 4 stays on after the last button is pressed on the control panel.

1. Go to the Back Light main level.
2. Select On (remains on), 10 S (10 seconds), 20 S (20 seconds), or 30 S (30 seconds).
3. Press .

Dimmer Curves The STRIKE 4 provides four different options to simulate the dimming curve of an incandescent lighting product.

1. Go to the Dimmer Mode main level.
2. Select a dimmer curve (Off, Dimmer 1, Dimmer 2, or Dimmer 3).

OFF: The output is proportional (linear) to the Dimmer channel values.

DIM1\~3: The output follows the Dimmer channel values based on the corresponding dimmer curve, being Dimmer 1 the fastest and Dimmer 3 the slowest.

Fixture Hours This option shows the total amount of hours the STRIKE 4 has been turned on.

1. Go to the Information main level.
2. Select Fixture Hours. (the hours will show on the screen)

LED Frequency This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the STRIKE 4.

1. Go to the LED Frequency main level.
2. Select PWM Frequency (600 Hz, 1200 Hz, 2000 Hz, 4000 Hz, or 25Khz).

Fan Control The STRIKE 4 allows you to adjust the fan speed of the product to allow for quiet operation.

1. Go to the Fan Mode main level.

2. Select Auto or High.

Menu Map

Main Level	Programming Levels			Description
Auto Show	Auto 1-6	Speed	0-100	Automatic programs
Static	Dimmer	0-255		Sets the intensity of the light output
	Strobe			Selects the strobe frequency
Dimmer Mode	Off			No dimmer
	Dimmer 1-3			Dimming curves Dimmer 1 (fast) to Dimmer 3 (slow)
Back Light	10S			Turns off display backlight after 10 sec of inactivity
	20S			Turns off display backlight after 20 sec of inactivity
	30S			Turns off display backlight after 30 sec of inactivity
	On			Display backlight always on
Information	Auto	Test		Turns on all LEDs in sequence for testing
	Fixture Hours			Shows total product hours
	Version			Shows installed software version
DMX Address	001-512			Selects DMX address (highest channel restricted to personality chosen)
DMX Channel	1 Ch			1-channel: dimmer
	3 Ch			3-channel: dimmer H, dimmer L, Strobe
	4 Ch			4-channel: pod 1-4
	9 Ch			9-channel: pod 1-4, auto programs, dimmer speed, dimmer H, dimmer L, strobe
Master/Slave Mode	Master			Master mode
	Slave			DMX mode (Slave mode)
Fan Mode	Auto			Fan control
	High
Temperature	LED1			Individual pod temperature
	LED2
	LED3
	LED4
LED Frequency	600Hz			PWM frequency
	1200 Hz
	2000 Hz
	4000 Hz
	25KHz

DMX Values

9 Ch	Channel	Function	Value	Percent/Setting
	1	Dimmer H	000 ° 255	0–100%
	2	Dimmer L	000 ° 255	0–100%
	3	Strobe	000 ° 010011 ° 132133 ° 255	No function0–20 Hz (All pods)0–20 Hz (Random strobe macros)
	4	White 1	000 ° 255	0–100%
	5	White 2	000 ° 255	0–100%
	6	White 3	000 ° 255	0–100%
	7	White 4	000 ° 255	0–100%
	8	Auto Programs	000 ° 010011 ° 040041 ° 080081 ° 120121 ° 160161 ° 200201 ° 240241 ° 255	No functionAuto 1Auto 2Auto 3Auto 4Auto 5Auto 6No function
	9	Dimmer Speed	000 ° 010011 ° 040041 ° 080081 ° 120121 ° 255	Preset dimmer speed from display menuNonlinear dimming curve 1 (fastest)Nonlinear dimming curve 2Nonlinear dimming curve 3 (slowest)Preset dimmer speed from display menu
1 Ch	Channel	Function	Value	Percent/Setting
	1	Dimmer H	000 ° 255	0–100%
3 Ch	Channel	Function	Value	Percent/Setting
	1	Dimmer H	000 ° 255	0–100%
	2	Dimmer L	000 ° 255	0–100%
	3	Strobe	000 ° 010 011 ° 132133 ° 255	No function0–20 Hz (All pods)0–20 Hz (Random strobe macros)
4 Ch	Channel	Function	Value	Percent/Setting
	1	White 1	000 ° 255	0–100%
	2	White 2	000 ° 255	0–100%
	3	White 3	000 ° 255	0–100%
	4	White 4	000 ° 255	0–100%

STRIKE 4 Pod Selection for DMX Control

STRIKE 4 Angle Adjustment for DMX Control

5. TECHNICAL INFORMATION

Product Maintenance

To maintain optimum performance and minimize wear, you should clean this product frequently. Usage and environment are contributing factors in determining the cleaning frequency.

As a rule, clean this product at least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear.

To clean your product:

1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external vents.
4. Clean all external surfaces with a mild solution of non-ammonia glass cleaner or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Wipe any dirt or grime to the outside edges of the lens surface.
7. Gently polish the lens surfaces until they are free of haze and lint.

Always dry the external surfaces thoroughly and carefully after cleaning them.

Do not spin the cooling fans while blowing compressed air into them.

1. TECHNICAL SPECIFICATIONS

Dimensions and Weight	Length	Width	Height	Weight
	14.2 in (362 mm)	6.4 in (163 mm)	14.2 in (362 mm)	19 lb (8.7 kg)
	Note: Dimensions in inches rounded to the nearest decimal digit.
Power	Power Supply Type	Range		Voltage Selection
	Switching (internal)	100–240 VAC, 50/60 Hz		Auto-ranging
	Parameter	120 VAC, 60 Hz		230 VAC, 50 Hz
	Consumption	301 W		286 W
	Current	2.49 A		1.29 A
	Power linking current (products)	13.6 A (5 products)		13.6 A (10 products)
	Fuse/Breaker	T 5 A, 250 V		T 5 A, 250 V
	Power I/O	U.S./Canada		Worldwide
	Power input connector	Neutrik powerCON A		Neutrik powerCON A
	Power output connector	Neutrik powerCON B		Neutrik powerCON B
	Power cord plug	Edison (U.S.)		Local plug
Light Source	Type	Power		Lifespan
	LED	100 W		50,000 hours
	Color	Quantity		Current
	White	4		2.3 A
Photometrics	Parameter	Total		Per Cell
	Illuminance @ 5 m	999 lux		242 lux
	Beam angle	49°
	Field angle	79°
Thermal	Max. External Temperature	Cooling System
	113 °F (45 °C)	Fan-Assisted Convection
DMX	I/O Connectors	Connector Type		Channel Range
	5-pin XLR	Sockets		1, 3, 4 or 9
Ordering	Product Name	Item Code		UPC Number
	STRIKE 4	03051079		781462214272

Photometrics Chart

Returns

You must send the product prepaid, in the original box, and with the original packing and accessories. Chauvet will not issue call tags.

Call Chauvet and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return.

Clearly label the package with an RMA number. Chauvet will refuse any product returned without an RMA number.

DO NOT write the RMA number directly on the box. Instead, write it on a properly affixed label.

Once you have received the RMA number, include the following information on a piece of paper inside the box:

• Your name
• Your address
• Your phone number
  The RMA number
  • A brief description of the problem(s)

Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be the customer's responsibility. FedEx packing or double-boxing is recommended.

Chauvet reserves the right to use its own discretion to repair or replace returned product(s).

CONTACT Us

USA WORLD HEADQUARTERS

General Information – Chauvet

Address: 5200 NW 108th Avenue

Sunrise, FL 33351

Voice: [phone]

Fax: [phone]

Toll free: [phone]

Technical Support

Voice: [phone] (Press 4)

Fax: [phone]

Email: [e-mail]

World Wide Web www.chauvetlighting.com

EUROPE

General Information - Chauvet Europe BVBA

Address: Stokstraat 18

9770 Kruishoutem

Belgium

Voice: [phone]

Technical Support

Email: [e-mail]

World Wide Web www.chauvetlighting.eu

General Information - Chauvet Europe Ltd.

Address: Unit 1C

Brookhill Road Industrial Estate

Pinxton, Nottingham, UK

NG16 6NT

Voice: [phone]

Fax: [phone]

Technical Support

Email: [e-mail]

World Wide Web www.chauvetlighting.co.uk

MEXICO

General Information - Chauvet Mexico

Address: Av. Santa Ana 30

Parque Industrial Lerma

Lerma, Mexico C.P. 52000

Voice: [phone]

Technical Support

Email: [e-mail]

World Wide Web www.chauvet.com.mx

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact the dealer of record. Follow their instructions to request support or to return a product. Visit our website for contact details.