70256 - Drill Draper - Free user manual and instructions
Find the device manual for free 70256 Draper in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of product | Drill |
| Brand | Draper |
| Model | 70256 |
| Category | Drill |
| Power supply | 230V AC, 50Hz |
| Input power | 600W |
| Chuck type | 13mm keyless chuck |
| No-load speed | 0 - 2,800 rpm |
| Impact function | Yes, suitable for masonry |
| Forward/reverse | Yes |
| Variable speed trigger | Yes |
| Lock button | For continuous operation |
| Dimensions (L x W x H) | 260 x 180 x 70 mm (approx.) |
| Weight | 1.6 kg |
| Power cable length | 2.5 m |
| Insulation class | Class II (double insulated) |
| Accessories included | Side handle, depth stop |
| Maintenance | Keep ventilation slots clean and wipe with dry cloth |
| Safety features | Double insulated, lock button to prevent accidental start |
| Spare parts and repair | Carbon brushes and chuck available for replacement |
| General information | Instruction manual available online in PDF format |
Frequently Asked Questions - 70256 Draper
What power supply does the Draper 70256 drill require?
The Draper 70256 drill operates on a standard 230V AC, 50Hz mains supply. It uses a 600W motor and is double insulated, so no earth connection is required.
How do I change the drill bit?
To change the drill bit, switch off and unplug the drill. Hold the keyless chuck with one hand and turn the sleeve with the other to open the jaws. Insert the new bit, then tighten the sleeve firmly by hand.
Can the 70256 drill be used in hammer mode for masonry?
Yes, the Draper 70256 is an impact drill with a switchable hammer action. For masonry, engage the hammer icon by sliding the collar to the hammer position. Select a speed suitable for the bit size.
What safety precautions should I take while using this drill?
Always wear safety goggles and ear protection. Ensure the work area is well-lit. Use the side handle for better control. Keep the power cord away from the moving bit. Do not force the drill; let it work at its own pace.
How do I reverse the direction of rotation?
The direction switch is located above the trigger. To reverse, stop the drill completely, then slide the switch to the opposite setting. The trigger still works the same, but the rotation direction is reversed. Change direction only when the chuck is fully stopped.
How do I clean and maintain the drill?
After each use, unplug the drill and wipe the exterior with a clean, dry cloth. Keep the ventilation slots free from dust and debris. Do not use water or solvents. Periodically clean the chuck and lightly oil internal moving parts if recommended.
What is the maximum drilling capacity of this drill?
The Draper 70256 can drill up to 13mm in wood and steel. In masonry, the capacity is typically around 13mm as well. Use the correct speed and allow the bit to cut without excessive pressure.
What should I do if the drill jams during operation?
If the drill jams, release the trigger immediately to stop the motor. Unplug the drill, then inspect the bit and the material. Remove any debris causing the jam. If the jam persists, check the chuck for damage.
How do I replace the carbon brushes?
Carbon brushes must be replaced when wear is visible. Remove the brush caps on the motor housing using a screwdriver. Pull out the worn brushes, insert new ones, and replace the caps. Ensure the brushes are seated properly. Replacing brushes is easier with the drill unplugged.
Is the drill suitable for screwdriving?
Yes, the 70256 features a variable speed trigger and a direction switch, making it suitable for driving screws. Use low speed for better control. A screwdriver bit can be inserted directly into the keyless chuck.
User questions about 70256 Draper
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Drill in PDF format for free! Find your manual 70256 - Draper and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 70256 by Draper.
USER MANUAL 70256 Draper
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Draper
Model : 70256
Category : Drill