TC-D11-1200 - Cutting machine Vevor - Free user manual and instructions
Find the device manual for free TC-D11-1200 Vevor in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Cutting machine (vinyl cutting plotter) |
| Brand | Vevor |
| Model | TC-D11-1200 |
| Maximum cutting width | 1200 mm |
| Media width | 1250 mm |
| Cutting speed | Adjustable from 20 to 100 mm/s |
| Cutting force | Adjustable from 80 to 500 g |
| Power supply | Power adapter 24 V DC, 100-240 V AC |
| Power consumption | 100 W max |
| Interface | USB port and RS-232 serial |
| Compatible software | SignMaster, ArtCut, CorelDraw |
| Operating systems | Windows XP, 7, 8, 10, 11 |
| Main functions | Cutting adhesive vinyl, thin cardboard, flex and stencils; pattern tracing |
| Included accessories | Blade, blade holder, tracing pen, USB cable, power supply, demonstration software |
| Dimensions (L x D x H) | 1450 x 250 x 300 mm |
| Weight | 18 kg |
| Noise level | Less than 60 dB |
| Maintenance and cleaning | Dust the cutting belt and rails; clean residue with a soft, non-abrasive cloth |
| Safety | Unplug before maintenance; do not touch the blade while moving; use under supervision |
| Spare parts and repairability | Blades, blade holders, belts and power supplies available; have repairs done by a qualified technician |
Frequently Asked Questions - TC-D11-1200 Vevor
How to install the machine and the software?
Connect the power, connect the plotter to your PC via USB, install the provided SignMaster software, then select the settings of the TC-D11-1200 in the driver preferences.
How to load the vinyl into the plotter?
Open the cover, insert the vinyl roll with the printable side facing down, align the edges with the width marks, close the cover and operate the pressure wheel to hold the media.
How to adjust the cutting force and speed?
In the software or via the control panel, adjust the force from 80 to 500 g and the speed from 20 to 100 mm/s depending on the material thickness. Do a test on a corner before starting a large job.
What to do if the blade does not cut deep enough?
Gradually increase the cutting force, check that the blade is properly inserted in the blade holder and that its tip protrudes slightly. Replace the blade if it is worn.
How to replace the blade?
Unplug the device, loosen the blade holder, insert a 45° or 60° blade, tighten it then adjust the protrusion using the wheel. Do a test on a piece of vinyl.
What materials can be cut?
This plotter cuts adhesive vinyl, heat transfer flex, thin cardboard and stencil films. Avoid materials that are too thick or abrasive to avoid damaging the blade.
How to clean and maintain the plotter?
After each use, dust the cutting belt and rails with a soft brush. For adhesive residue, use a slightly damp cloth without aggressive solvents.
What to do in case of a media jam?
Turn off the device, carefully remove the jammed material and check that the cutting belt is intact. Then reload following the indicated insertion path.
Why are the cuts misaligned?
Check that the roll is properly positioned and that the pressure of the wheels is uniform. Run a calibration in the software and use the machine marks to align the media.
Where to find spare parts and get the device repaired?
Blades, blade holders, belts and power supplies are available on the Vevor website. For internal repairs, contact a qualified technical service.
User questions about TC-D11-1200 Vevor
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Cutting machine in PDF format for free! Find your manual TC-D11-1200 - Vevor and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TC-D11-1200 by Vevor.
USER MANUAL TC-D11-1200 Vevor
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Vevor
Model : TC-D11-1200
Category : Cutting machine