TA-890 - Paint gun Vevor - Free user manual and instructions
Find the device manual for free TA-890 Vevor in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Pneumatic paint spray gun (HVLP) |
| Brand | Vevor |
| Model | TA-890 |
| Power supply | Compressed air (pneumatic) |
| Nozzle diameter | 1.7 mm (compatible with paints and varnishes) |
| Cup capacity | 600 ml (aluminum top cup) |
| Recommended operating pressure | 3.0 - 4.0 bars |
| Average air consumption | 113 - 227 L/min |
| Suitable viscosity | 20-35 seconds (DIN 4 cup) |
| Anti-drip nozzle | Yes, with flow adjustment |
| Spray pattern adjustment | Horizontal, vertical and circular |
| Tool weight | Approximately 0.65 kg |
| Dimensions (L x W x H) | 180 x 120 x 50 mm |
| Body material | Lightweight aluminum alloy |
| Maintenance and cleaning | Solvent cleaning after each use |
| Safety | Wear PPE: mask, safety glasses, gloves |
| Functions | Application of paints, varnishes, primers, stains |
| Certification / standard | Compliant with usual safety standards |
| Spare parts | Nozzle, needle, valves, seals available |
| Repairability | Removable, easy maintenance |
| Included accessories | Extra nozzle, cleaning key, grease tube |
| General information | French user manual PDF available online |
Frequently Asked Questions - TA-890 Vevor
How to adjust the air pressure of the TA-890 spray gun?
Use a pressure gauge on the compressor. The ideal pressure is between 3 and 4 bars. Adjust with the regulator, and test on a scrap piece to obtain a uniform spray.
How much paint can I put in the cup?
The top cup has a capacity of 600 ml. Fill it three-quarters full to avoid leaks, and close the lid securely.
How to clean the gun after water-based painting?
Disassemble the nozzle, needle and valve. Rinse the parts with clean water then with a suitable solvent, and dry thoroughly before reassembly.
My spray pulses, what to do?
Check that the nozzle is not partially clogged, that the paint is sufficiently fluid (proper dilution), and that the pressure is stable. Clean the air and paint channels.
Can I spray alkyd paint with this gun?
Yes, thin the paint with a suitable solvent until reaching a viscosity of 20-35 seconds on DIN 4 cup. Mix well before pouring into the cup.
How to adjust the spray direction (horizontal/vertical)?
Turn the ring located in front of the nozzle. By aligning the mark, the spray becomes horizontal, vertical or circular depending on the position. Then lock the ring.
What protective equipment should I wear?
Always wear a respiratory protection mask, tight-fitting safety glasses and suitable gloves. Work in a ventilated area.
The gun does not spray, why?
Check that the air supply is open, that the needle is not blocked by residue, and that the air valve works. Disassemble, clean, and lubricate the moving parts.
What dilution for thick paint?
Add 10 to 15% thinner (depending on paint) and test the fluidity. A consistency of "whole milk" gives a good finish. Use a densimeter or DIN 4 cup.
Where to find spare parts for the TA-890?
Parts such as the nozzle, needle and cup gasket are available on the Vevor website and from authorized dealers. Use the references from the manual.
User questions about TA-890 Vevor
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Paint gun in PDF format for free! Find your manual TA-890 - Vevor and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TA-890 by Vevor.
USER MANUAL TA-890 Vevor
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Vevor
Model : TA-890
Category : Paint gun