X79463MD20 - Range hood AEG - Free user manual and instructions

Find the device manual for free X79463MD20 AEG in PDF.

AEG X79463MD20 - Range hood
📄 164 pages English EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs
Notice AEG X79463MD20 - page 2
2 / 164
Pick your language and provide your email: we'll send you a specifically translated version.
Product type Wall-mounted cooker hood
Brand AEG
Model X79463MD20
Width 90 cm
Depth 50 cm
Height 65.5 to 105 cm
Net weight Approx. 19 kg
Power supply 220-240 V, 50 Hz
Motor power 250 W
Maximum airflow rate 720 m³/h
Number of speeds 3 + 1 intensive
Control Push buttons
Lighting 2 integrated LEDs
Grease filter Metal, dishwasher-safe
Activated carbon filter Replaceable, optional
Noise level 44 to 66 dB(A)
Energy class A
Repairability index 7.9/10
Safety Delayed shutdown, overheating cut-off
Maintenance Clean filters and surfaces with a soft cloth
Spare parts Filters, LED bulbs, optional remote control
Installation Extraction or recirculation mode

Frequently Asked Questions - X79463MD20 AEG

How to install the X79463MD20 hood in extraction mode?
Connect the air outlet to a heat-resistant duct that exhausts to the outside. Respect the minimum distances indicated in the manual, then attach the appliance to the wall with the supplied plugs.
How to turn on the hood and adjust the speed?
Press the On button, then use the Speed control to choose between 1 and 3. The Intensive button activates maximum extraction for a few minutes.
How to clean the grease filters?
The metal filters can be cleaned in the dishwasher with a mild detergent. Allow them to dry completely before reinstalling. Replacement is recommended after 3 years of use.
When to replace the activated carbon filter?
The carbon filter should be replaced approximately every 6 months, or sooner if the hood is used intensively. This filter is only necessary in recirculation mode.
Should the hood be cleaned before first use?
Yes, wipe the exterior surfaces and filters with a slightly damp cloth. Then run the hood on intensive speed for 10 to 15 minutes without any load.
How to replace the LED bulb?
First cut off the power supply. Open the lighting compartment, unclip the bulb and replace it with a 1.5 W LED. Use the bulb type indicated on the label.
The remote control no longer responds, what should I do?
Check the batteries and the distance from the sensor. If nothing works, turn off the hood, wait 2 minutes, then turn it back on. For remote controls, replace the batteries with new ones.
What is the minimum height between the cooking hob and the hood?
The manual recommends a minimum of 65 cm for an electric cooker and 75 cm for a gas or mixed cooker.
How to switch the hood to recirculation mode?
Install the activated carbon filter(s) on either side of the fan, after removing the grease filters. Reclip the grease filters over them, then select recirculation mode using the control.
How to reduce the noise level of the hood?
Clean the filters regularly to avoid blockages. Use speed 1 for gentle cooking and speed 2 or 3 for heavier cooking. Check that the duct is securely attached.

User questions about X79463MD20 AEG

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Range hood in PDF format for free! Find your manual X79463MD20 - AEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. X79463MD20 by AEG.

USER MANUAL X79463MD20 AEG

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : AEG

Model : X79463MD20

Category : Range hood