XLf 16150 A - Washing machine BLAUPUNKT - Free user manual and instructions

Product Type	Active Subwoofer
Speaker Size	6.5" (165 mm)
Cone Composition	Aluminum
Magnet Type	Ferrite
Enclosure Housing Material	Die-cast Aluminum
Enclosure Dimensions (L x W x H)	205 x 170 x 70 mm
Enclosure Net Weight	4.5 kg
Amplifier Technology	Class D
Normal Output Power (RMS)	150 W
Max. Power Output	300 W
Sensitivity (In Car / 1W)	>95 dB
Signal / Noise Ratio	>95 dB
Impedance	0.4 ohms
Frequency Response	25 Hz - 150 Hz
Low Pass Filter	40 Hz - 160 Hz
Input Voltage Range	10 V - 16 V (rated 14.4 V)
Phase Switch	0° / 180°
Automatic On / Off	High Level Input Only
Audio Input Sensitivity	Speaker Input: 140 mV - 5.4 V; RCA Input: 280 mV - 10.8 V
Protection	Integrated fuse
Installation Location	Dry and well-ventilated area
Included Accessories	Screws, mounting brackets, 4-pin high level input cable, 4.5 m remote controller

Frequently Asked Questions - XLf 16150 A BLAUPUNKT

How do I install the Blaupunkt XLf 16150 A subwoofer in my car?

Disconnect the vehicle's negative battery terminal first. Choose a dry, well-ventilated location and ensure it is stable for screw mounting. Connect the power cable with a minimum cross-section of 2.5 mm² if runs are long, and connect the ground securely to chassis. Refer to the wiring diagram in the manual for exact connections.

Where should I place the subwoofer for best performance?

The subwoofer can be mounted in an up-firing or side-firing position. For optimal bass response, place it in a location that allows air to circulate around the enclosure. Avoid placing it on the rear shelf or seat where it could be exposed to direct sunlight or moisture.

How does the auto turn-on function work on this device?

This subwoofer automatically powers on when an audio signal is detected on the high-level (speaker) input. It also turns off automatically when the signal stops. If your head unit does not provide a remote trigger, use the DC/REM switch to select the appropriate method.

What is the correct setting for the Low Pass Filter?

The low pass filter can be adjusted between 40 Hz and 160 Hz. Start with a setting around 80-100 Hz to blend smoothly with your main speakers. Adjust according to your listening preference and the capabilities of your speakers.

The protection LED lights up when I turn it on. What should I do?

First check the speaker wires for short circuits. Reduce the volume on your head unit to avoid overdriving the device. If the LED remains on after resetting the device, the amplifier may need service. Turn off the device and consult an authorized Blaupunkt dealer.

How do I connect high-level inputs from a factory head unit?

Use the included 4-pin high level input cable. Connect the wires to the speaker outputs of your factory head unit, ensuring correct polarity (+ and -). The subwoofer senses this signal to turn on and process audio.

What is the phase switch for and how do I set it?

The phase switch (0° or 180°) reverses the polarity of the subwoofer output. This helps align the subwoofer's sound wave with that of your main speakers for better bass integration. Try both positions and listen to determine which gives the strongest, most natural bass.

Can I use this active subwoofer in a home audio system?

This product is designed for 12V car electrical systems (10-16V). Connecting it to a home AC outlet would require a converter and may be unsafe. It is intended for mobile use only.

How do I adjust the input gain and what is a safe setting?

The input gain control (MIN to MAX) adjusts the input sensitivity to match your head unit's signal level. Always start with the gain at a low setting and increase gradually until you hear distortion, then back off slightly. Match the input sensitivity to either speaker level (140mV-5.4V) or RCA level (280mV-10.8V) as appropriate.

How do I maintain and clean the subwoofer?

Keep the enclosure clean with a dry, soft cloth. Check all wiring connections periodically for tightness and corrosion. Ensure the ventilation around the amplifier is unobstructed. Do not use harsh chemicals or water to clean the unit.

USER MANUAL XLf 16150 A BLAUPUNKT

ACTIVE SUBWOOFER XLf 16150 A

Enjoy it.

Proper system planning is vital in order to maximize the device's performance and road safety. Plan your installation carefully to avoid compromising performance reliability of the system. Consult an authorized Blaupunkt dealer for installation or preparation. Read the manual carefully before operating the device for the first time.

Safety Notes

Ensure to follow below safety notes during installation and wiring connection: -

• Disconnect the negative terminal of the battery. Refer to the safety notes of the vehicle manufacturer.
• Ensure positions of the holes are nowhere near the vehicle component to avoid any damage during drilling.
• Ensure cross section of the cable is no less than 2.5mm² if the positive and negative cables are too long.
• Incorrect installation may result in malfunction of the device or the car sound system.

Installation and Connection Instructions

• Select a dry and well-ventilated location to install the device.
• The device must not be installed in overly exposed location such on the rear shelf, rear seat etc.
• The installation location must be suitable for screw holes and have stable ground support.

Integrated Fuse

• The integrated fuse in the device protects the output voltage and the entire electrical system in case of malfunction. Do not replace damaged fuse with higher current.

Switching On/Off

- This device will automatically turn on if audio signal is detected. The device will also automatically turn off if audio signal is received.

Disclaimer

In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products.

USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.

Disposal Notes

Do not dispose of your old unit in the household trash!

Use the return and collection systems available to dispose of the old device.

This manual may be updated from time to time without any notice. Visit www.blaupunkt.com for more info.

If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist.

Problem	Solution
Amplifier power up failure	Examine if the ground connection is intact.
	Examine if remote input has at least 5V DC.
	Examine if battery power is connected correctly to the + terminal.
	Ensure supplied voltage is minimum 12V.
	Examine if fuse is broken and replace if necessary.
	Restart the device if protection LED light is on.
Protection LED lights on when turn on	Examine if speaker wire had short-circuit.
	Turn volume down from head unit to prevent overdriving the device.
	Device might need service or repair, if protection LED light is still on after resetting the device.
No sound output	Examine fuses and replace if necessary.
	Examine if ground connection is intact.
	Examine if remote input has at least 5V DC.
	Examine if RCA audio cables are connected to the right inputs.
	Examine if speaker wiring is intact.
Low sound output	Reset Level Control
	Examine the Crossover Control setting.
Buzzing noise	Observe if the device is still producing noise after turning on and off the amplifier. If yes, examine if the cables are correctly connected and if the cables and radio are in good condition. Repair or replace if the cables or the radio are not in good condition.
Squealing noise interference	Ensure RCA connections are properly connected.
Distorted sound output	Ensure input level of the device matches the signal level of the head unit.
	Always set the input level to the lowest.
	Examine if crossover frequency is set correctly.
	Examine if speaker wire had short-circuit.
Amplifier temperature increased	Examine if the minimum speaker impedance for the amp models is correct.
	Ensure good air ventilation around the device. Add external cooling fan if necessary.
Engine noise (static sound) interference	Usually caused by poor RCA cable quality, which release noise. Use only the best quality cables, and route them away from power cables.
Engine noise (alternator whine) interference	Examine if RCA cable are nowhere near or attached to the vehicle chassis.
	Examine if head unit is properly connected to the wires.

1. Power Input Terminal
2. Input Select (LOW/HI)
3. Phase ( 0° \~ 180° )
4. Power LED

5. Audio Input

6. Input Gain (MIN \~ MAX)

7. Low Pass (40Hz \~ 160Hz)
8. Bass Boost (0 \~ +12dB)
9. Auto Turn ON Method (DC/REM)
10. Remote Control Input

WIRING DIAGRAM

INSTALLATION POSITION

Up Firing Position

Side Firing Position

Subwoofer

• Speaker Size : 6.5" (165mm)
• Cone Composition : Aluminum
• Magnet Type : Ferrite
  • Enclosure Housing Material : Die-cast Aluminum
  • Enclosure Dimension (LxWxH) : 205x170x70mm
  • Enclosure Net Weight : 4.5kg

Amplifier

• Amplifier Technology : Class D
• Normal Output Power (RMS) : 150W

• Max. Power Output : 300W
• Sensitivity (In Car/1W) : >95dB
• Signal / Noise Ratio (dB) : >95dB
- Impedance: 0.4 ohms
• Frequency Response : 25Hz-150Hz
• Low Pass Filter : 40Hz-160Hz
• Voltage : 14.4V (10V-16V)
• Phase Switch : 0 deg / 180 deg
• Automatic On/Off : High Level Input Only
- Audio in Sensitivity : Speaker Input (140mV-5.4V)/RCA Input (280mV-10.8V)

Accessories

2 x Screws (M5x10mm)

2 x Screws (M4x20mm)

2 x Mounting Bracket (45x22x6mm)

1 x 4 Pin High Level Input Cable

1 x 4.5m Remote Controller

Blaupunkt Car Entertainment - Asia Pacific Competence Centre

RO

1 113 25 039 02 01