WP3010 - Uncategorized BLAUPUNKT - Free user manual and instructions
Find the device manual for free WP3010 BLAUPUNKT in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Submersible Water Pump |
| Brand | Blaupunkt |
| Model | WP3010 |
| Power Supply | 230–240 V AC, 50 Hz |
| Power Consumption | 750 W |
| Max Flow Rate | 8,000 L/h |
| Max Delivery Head | 8 m |
| Max Immersion Depth | 7 m |
| Max Liquid Temperature | 35 °C |
| Outlet Connection | 1 inch (25 mm) threaded |
| Protection Rating | IPX8 |
| Pump Housing Material | Stainless Steel |
| Impeller Material | Engineering Plastic |
| Motor Type | Induction Motor |
| Float Switch | Automatic ON/OFF |
| Thermal Protection | Built-in Overload Protection |
| Cable Length | 10 m |
| Dimensions | 185 × 185 × 330 mm |
| Weight | 4.2 kg |
| Applications | Garden Watering, Rainwater Harvesting, Flood Drainage |
| Maintenance | Regular Inspections of Seal and Impeller |
| Cleaning | Rinse with Clean Water After Use |
| Safety | Use Only Via RCD, Not for Swimming Pools |
| Spare Parts | Impeller, Seals, Float Switch, Power Cable |
Frequently Asked Questions - WP3010 BLAUPUNKT
Can I use the WP3010 to pump sea water?
No, the WP3010 is designed for clean water only. Pumping seawater can cause corrosion and damage the pump. Use it only for freshwater, rainwater, or grey water.
How do I connect a garden hose to the pump?
Attach a standard garden hose to the pump's 1-inch threaded outlet. Use PTFE tape to ensure a watertight connection. Tighten the adapter with a wrench, but do not overtighten.
Why is the pump not starting even when the water level is high?
Check the float switch – it must move freely. If it is stuck or obstructed, it will not activate the pump. Also verify the power supply, the RCD, and the ON/OFF switch.
Can the pump run dry?
No, running the pump dry can damage the mechanical seal and the motor. Always ensure the pump is submerged to a level where the float switch can operate properly.
What is the maximum immersion depth?
The maximum immersion depth is 7 meters below the water surface. Do not install the pump deeper, as the pressure could damage the seals and housing.
How to clean the pump after use in muddy water?
After pumping dirty water, rinse the pump thoroughly with clean water. Remove the bottom screen or filter and clean any debris. Let the pump dry completely before storing.
How to store the pump during winter?
Drain all water from the pump, pipes, and any attached hoses. Clean the inlet screen and dry the pump. Store it in a frost-free room to prevent damage from freezing.
Why is the pump cycling on and off repeatedly?
This usually indicates a leaking hose or a clogged inlet. Check all connections and the non-return valve. Also adjust the float switch travel range if needed.
Can I use an extension cord with the pump?
Yes, but the extension cord must be grounded and rated for outdoor use. Keep the cord length as short as possible and use a cross-section of at least 1.5 mm².
How to replace the power cable if it is damaged?
The power cable must be replaced by a qualified technician or an approved service center. Do not attempt to repair it yourself, as this could compromise electrical safety.
User questions about WP3010 BLAUPUNKT
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual WP3010 - BLAUPUNKT and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. WP3010 by BLAUPUNKT.
USER MANUAL WP3010 BLAUPUNKT
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : BLAUPUNKT
Model : WP3010
Category : Uncategorized