31-6113 - Uncategorized Clas Ohlson - Free user manual and instructions
Find the device manual for free 31-6113 Clas Ohlson in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Digital Multimeter |
| Brand | Clas Ohlson |
| Model | 31-6113 |
| Display | 3½-digit LCD, 1999 counts |
| DC voltage ranges | 200 mV, 2 V, 20 V, 200 V, 1000 V |
| AC voltage ranges | 200 V, 750 V |
| DC current ranges | 200 µA, 2 mA, 20 mA, 200 mA, 10 A |
| Resistance ranges | 200 Ω, 2 kΩ, 20 kΩ, 200 kΩ, 2 MΩ, 20 MΩ |
| Additional functions | Diode test, continuity buzzer, transistor test |
| Power supply | 9 V battery (6F22) |
| Dimensions | 150 × 70 × 32 mm (approx.) |
| Weight | 150 g including battery |
| Safety rating | CAT II, 1000 V |
| Operating temperature | 0 °C to 40 °C |
| Storage temperature | -10 °C to 50 °C |
| Auto-off | After 15 minutes |
| Maintenance | Clean with a dry cloth; replace battery when low |
| Repairability | Battery replacement only; no user-serviceable parts |
| General information | Manual available in 4 languages (EN, DE, FI, SV), 24 pages |
Frequently Asked Questions - 31-6113 Clas Ohlson
How do I measure DC voltage?
Set the dial to the V (DC) position, connect the test leads to the device, and read the display. Make sure the red lead is in the VΩmA terminal and the black lead in COM. For unknown values, start with the highest range and work down.
What do the symbols on the dial mean?
The dial positions represent functions: V for voltage (DC or AC), A for current, Ω for resistance, and the sound wave icon for continuity. A battery icon indicates the battery is low.
How do I perform a continuity test?
Turn the dial to the continuity symbol, connect the leads across the circuit. If resistance is below approximately 100 Ω, the buzzer sounds continuously.
How do I replace the battery?
Remove the screw from the back cover, lift the cover, and disconnect the old battery from the snap connector. Attach a new 9 V battery, close the case, and tighten the screw.
What is the maximum voltage I can measure?
The maximum DC voltage is 1000 V, and the maximum AC voltage is 750 V. Do not exceed these limits to avoid damage or injury.
How do I measure resistance?
Ensure the circuit is de-energized, then set the dial to Ω mode, connect the test leads across the resistor, and read the value. For in-circuit measurements, isolate the component.
Why does the display show '1' or 'OL'?
This indicates an overload or an open circuit. It means the value is above the selected range or no connection is made. Select a higher range or check the leads.
Does the multimeter have an auto-off function?
Yes, it automatically powers off after 15 minutes of inactivity. You can turn it back on by pressing any button or rotating the dial.
How should I care for the multimeter?
Keep the device clean and dry. Wipe the case with a soft cloth slightly dampened with water. Do not use solvents or abrasive cleaners.
Is it safe to measure voltage on a live circuit?
Yes, if you observe safety precautions. Use the correct range and rating (CAT II up to 1000 V). Never connect the device to a circuit exceeding the maximum limits, and follow standard electrical safety procedures.
User questions about 31-6113 Clas Ohlson
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual 31-6113 - Clas Ohlson and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 31-6113 by Clas Ohlson.
USER MANUAL 31-6113 Clas Ohlson
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Clas Ohlson
Model : 31-6113
Category : Uncategorized