ZDT-FCA2 - Uncategorized PHOENIX GOLD - Free user manual and instructions
Find the device manual for free ZDT-FCA2 PHOENIX GOLD in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 2-Channel Car Audio Amplifier |
| Brand | Phoenix Gold |
| Model | ZDT-FCA2 |
| Number of Channels | 2 |
| Peak Power Output | 400 W (200 W × 2) |
| RMS Power Output (4 Ω) | 100 W × 2 |
| RMS Power Output (2 Ω) | 150 W × 2 |
| Bridged RMS Power (4 Ω) | 300 W × 1 |
| Frequency Response | 20 Hz – 20 kHz (±1 dB) |
| Total Harmonic Distortion | < 0.1% |
| Signal-to-Noise Ratio | > 100 dB |
| Input Sensitivity | 0.2 V – 6 V |
| Crossover Frequency Range | 50 Hz – 500 Hz |
| Bass Boost | 0 – 12 dB at 45 Hz |
| Power Supply Voltage | DC 12 V (10 – 15 V allowed) |
| Dimensions (W × H × L) | 7.5 × 2.2 × 12.6 inches |
| Weight | 5.5 lbs |
| Protection Features | Thermal, over-current, short-circuit, DC offset |
| Installation and Mounting | 4 mounting screws included |
| Maintenance | Clean with a dry cloth; ensure proper ventilation |
| Safety | Professional installation recommended |
| Spare Parts and Repairability | Available through authorized Phoenix Gold dealers |
Frequently Asked Questions - ZDT-FCA2 PHOENIX GOLD
What is the Phoenix Gold ZDT-FCA2 amplifier?
The ZDT-FCA2 is a 2-channel car audio amplifier that delivers 100 watts RMS per channel at 4 ohms, ideal for powering door speakers or a small subwoofer.
How do I wire the power and ground connections?
Connect the 12V terminal to the positive battery post through an inline fuse, and the GND terminal to a bare metal chassis ground. Make sure all connections are tight and use appropriate wire gauge.
What speaker impedance is supported?
The amplifier is stable at 4 ohms and 2 ohms per channel, and can also be bridged for a 4-ohm mono operation.
How do I adjust the input gain?
Start with the gain knob at minimum, play your head unit at about 75% volume, then slowly increase until you hear distortion, then back off slightly. Use the input sensitivity range of 0.2–6V.
Does it have a crossover for system tuning?
Yes, it features a built-in low-pass/high-pass crossover adjustable between 50 Hz and 500 Hz, plus a 12 dB bass boost at 45 Hz.
What should I do if the amplifier shuts down?
Check for overheating, short circuits, or improper power/ground connections. The built-in protection circuits activate to safeguard the unit. Ensure adequate ventilation and correct wiring.
Can I use this amplifier in a home stereo system?
It is designed for 12V DC car audio systems, so you would need a power supply to use it at home, but it is not recommended due to current draw.
How do I clean and maintain the amplifier?
Use a soft, dry cloth to wipe the exterior. Do not use water or cleaning agents. Periodically check that the cooling fins are not blocked by dust or debris.
Is it compatible with factory head units?
Yes, its input sensitivity range of 0.2–6V allows compatibility with both factory and aftermarket radios. You may also need a line output converter if your head unit lacks RCA outputs.
Where can I get spare parts or repair service?
Contact an authorized Phoenix Gold dealer or their support team for genuine spare parts and service. The amplifier has a replaceable fuse and accessible terminals for servicing.
User questions about ZDT-FCA2 PHOENIX GOLD
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual ZDT-FCA2 - PHOENIX GOLD and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ZDT-FCA2 by PHOENIX GOLD.
USER MANUAL ZDT-FCA2 PHOENIX GOLD
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : PHOENIX GOLD
Model : ZDT-FCA2
Category : Uncategorized