Ultimate IGS12T-BRZ-T-EACH - Loudspeaker Crestron - Free user manual and instructions
Find the device manual for free Ultimate IGS12T-BRZ-T-EACH Crestron in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Outdoor In-Ground Loudspeaker |
| Brand | Crestron |
| Model | Ultimate IGS12T-BRZ-T-EACH |
| Finish | Bronze (powder-coated) |
| Driver Configuration | 2-way (12" woofer + 1" tweeter) |
| Woofer Diameter | 12 inches (30.5 cm) |
| Tweeter Diameter | 1 inch (2.54 cm) |
| Frequency Response | 45 Hz - 20 kHz |
| Power Handling (RMS) | 120 Watts |
| Peak Power Handling | 240 Watts |
| Impedance (Bypass Mode) | 8 Ohms |
| Transformer Taps (70V) | 15 W, 30 W, 60 W, 120 W |
| Transformer Taps (100V) | 30 W, 60 W, 120 W |
| Sensitivity | 95 dB SPL (1W/1m) |
| Max SPL | 115 dB |
| Enclosure Material | UV-stabilized ABS resin |
| Grille Material | Aluminum with bronze finish |
| Weather Rating | IP66 |
| Dimensions (H × D) | 17.6 × 15.2 inches (44.7 × 38.6 cm) |
| Weight | 22 lbs (10 kg) |
| Installation | Flush in-ground mount with radial flange |
| Termination | Screw terminals with waterproof cap |
| Maintenance | Clean grille with mild soap and water; avoid pressure washing |
| Safety | Connect only to low-voltage audio circuits; follow local codes |
| Spare Parts | Available from Crestron dealers |
Frequently Asked Questions - Ultimate IGS12T-BRZ-T-EACH Crestron
How do I connect the Crestron IGS12T to my amplifier?
For 8-ohm direct connection, use the bypass (LO-Z) setting on the transformer. If using a 70V/100V distributed audio system, select the appropriate tap to match the amplifier and speaker budget. Connect the positive and negative terminals from the amplifier or transformer output to the speaker's screw terminals, and ensure the weatherproof cap is tightened.
What is the difference between 70V and 8-ohm mode?
In 8-ohm mode, the speaker is directly connected to a standard amplifier output, providing full power. In 70V/100V mode, the built-in transformer matches the speaker to a constant-voltage distributed line, allowing multiple speakers to be used on one amplifier with separate tap settings. This is ideal for commercial installations.
How do I select the correct transformer tap?
Calculate the total power you want to allocate to the speaker (typically 15W, 30W, 60W, or 120W at 70V). Choose a tap that is at or slightly below the connected transformer's output power. For a 60W amplifier output, set the tap to 60W. If you're not sure, start with a lower tap to avoid distortion.
Can I use the speaker outdoors in rainy conditions?
Yes, the IGS12T has an IP66 weather rating, meaning it is protected against heavy seas or powerful jets. It is designed for outdoor landscape installation. Ensure the wire connections are sealed with the provided waterproof cap to maintain the IP rating.
How deep should I bury the speaker?
Install the speaker so that the top of the grille is flush with the ground level. The body extends downward; recommend a depth of at least 12 inches (30 cm) for the base, leaving room for the wire. Follow the provided template and ensure the soil is well-drained.
Can I mix multiple speakers on one amplifier?
Yes, if you use 70V/100V mode. Connect each speaker to the line with its transformer tap set appropriately. The sum of selected taps should not exceed the amplifier's rated output power. For 8-ohm mode, use careful parallel/series wiring and ensure the total impedance is within the amplifier's range.
What is the recommended speaker wire gauge?
For runs under 100 feet, use 16 AWG. For runs up to 200 feet, switch to 14 AWG. In 70V systems, 14 AWG is normally sufficient for up to 500 feet. Always use outdoor-rated direct burial wire.
How do I clean and maintain the speaker?
Remove the grille if necessary and rinse with a garden hose on a low setting. Use a soft brush and mild soap to remove stubborn dirt. Do not use a pressure washer as it may damage the diaphragm. Check the surrounding area periodically to ensure no debris or vegetation is blocking the grille.
Is the Crestron IGS12T compatible with third-party amplifiers?
Yes, the speaker has a standard impedance and transformer taps that are compatible with virtually any audio amplifier or 70V/100V distributed audio system. The only requirement is that the amplifier can deliver at least the rated power and, in 70V mode, has a corresponding transformer output.
What is the warranty coverage?
Crestron provides a limited lifetime warranty on the IGS12T. This covers defects in materials and workmanship under normal and proper use. Exclusions include misuse, unauthorized modification, and outdoor damage due to improper installation. Contact your Crestron dealer for details and service.
User questions about Ultimate IGS12T-BRZ-T-EACH Crestron
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Loudspeaker in PDF format for free! Find your manual Ultimate IGS12T-BRZ-T-EACH - Crestron and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Ultimate IGS12T-BRZ-T-EACH by Crestron.
USER MANUAL Ultimate IGS12T-BRZ-T-EACH Crestron
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Crestron
Model : Ultimate IGS12T-BRZ-T-EACH
Category : Loudspeaker