DPT412PSSKR-3 - Uncategorized Micro Matic - Free user manual and instructions
Find the device manual for free DPT412PSSKR-3 Micro Matic in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Kegerator / Draft Beer Dispenser |
| Brand | Micro Matic |
| Model | DPT412PSSKR-3 |
| Capacity | 4.2 cubic feet (118 liters) |
| Refrigerant | R600a (environmentally friendly) |
| Temperature Range | 33°F to 40°F (0.5°C to 4.5°C) |
| Voltage | 115 V AC, 60 Hz |
| Power Consumption | 100 W |
| Dimensions (W x D x H) | 18.5 x 18.5 x 33.5 inches (47 x 47 x 85 cm) |
| Weight | 68 lbs (31 kg) |
| Door Material | Stainless steel |
| Interior Material | Food-grade plastic |
| Lighting | Interior LED light |
| Thermostat | Adjustable digital thermostat |
| Compressor | Sealed compressor |
| Defrost | Automatic |
| Door Lock | Yes, with key |
| Caster Wheels | 4 locking casters |
| Recommended Keg | 1/6 barrel or 5-gallon cornelius keg |
| Included | Tap tower with faucet, CO2 regulator, CO2 tank, beer line |
| Certification | ETL / CETL certified |
Frequently Asked Questions - DPT412PSSKR-3 Micro Matic
How do I set up my DPT412PSSKR-3 kegerator?
Place the unit on a level surface and let it sit upright for 2-3 hours before plugging in. Connect the keg coupler to the keg, attach the CO2 tank with regulator, and set the digital thermostat to 38°F (3.3°C). The beer will be ready to serve after carbonation.
What keg sizes are compatible?
The kegerator accepts standard 1/6 barrel (5.16 gallons) and 5-gallon cornelius kegs. It does not fit full-sized 15.5-gallon half-barrels.
How do I clean the beer lines?
Remove the keg and run a solution of warm water with mild beer line cleaner through the dispensing line using a manual pump. Rinse thoroughly with fresh water and reconnect a new keg.
Why is my beer foamy when pouring?
Foam is usually caused by warm temperature or excessive pressure. Lower the thermostat to 38°F (3.3°C) and reduce the CO2 pressure to 10-12 psi. Also ensure you use a clean glass.
How often should I perform maintenance?
Clean the condenser coils every 6 months, check the door seal for good closure, and sanitize the dispensing lines annually or whenever you change kegs.
Can I control the temperature precisely?
Yes, the digital thermostat allows adjustment in 1°F increments between 33°F and 40°F, with an LED display showing the current temperature.
Is the kegerator easy to move?
It features 4 locking caster wheels at the base. Unlock to roll, then lock them again to keep the unit firmly in place.
What should I do if the kegerator is not cooling?
Check the power cord, ensure the thermostat is set below room temperature, and inspect the condenser coils for dust. If the compressor does not run, contact Micro Matic support for troubleshooting.
Does the kegerator require special installation?
No, it is a standalone appliance. Simply keep 5 inches (13 cm) of clearance on all sides for ventilation and plug into a grounded outlet.
How do I force carbonate beer in this kegerator?
Set the CO2 pressure to 20-30 psi for 24 hours, then drop it to serving pressure (10-12 psi). Test the beer's carbonation and adjust as needed.
User questions about DPT412PSSKR-3 Micro Matic
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual DPT412PSSKR-3 - Micro Matic and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DPT412PSSKR-3 by Micro Matic.
USER MANUAL DPT412PSSKR-3 Micro Matic
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Micro Matic
Model : DPT412PSSKR-3
Category : Uncategorized