Flex System x222 - Server IBM - Free user manual and instructions
Find the device manual for free Flex System x222 IBM in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Server |
| Brand | IBM |
| Model | Flex System x222 |
| Category | Server |
| Form factor | High-density compute node for IBM Flex System chassis |
| Dimensions | Approximately 107 mm (W) x 305 mm (H) x 245 mm (D) |
| Weight | Approximately 6.4 kg (empty) |
| Power supply | Powered by the Flex System chassis backplane; supports redundant power supplies in chassis |
| Main functions | Provides two independent server nodes in a single half-width slot, enabling high-density computing |
| Supported processors | Two Intel Xeon E5-2600 v2 series processors per node |
| Memory support | Up to 12 DDR3-1866 MHz DIMMs per node (24 per node), 384 GB max per node |
| Storage support | Integrated SATA/SAS controller with up to two 2.5-inch hot-swappable drives per node |
| Networking | Dual Gigabit Ethernet ports per node; optional 10Gb Ethernet adapters |
| Management | Integrated Management Module II (IMM2) for remote management |
| Expansion capability | One PCIe Gen3 x16 mezzanine connector per node |
| Operating temperature | 10°C to 35°C (50°F to 95°F) at sea level |
| Operating humidity | 20% to 80% RH (non-condensing) |
| Safety | Install only in a suitable Flex System chassis; disconnect power before service; follow ESD practices |
| Maintenance and cleaning | Dust regularly; use a soft dry cloth; avoid liquids; ensure good airflow |
| Spare parts and repairability | Modular design enables easy replacement of memory, drives, and system boards; IBM warranty and support available |
| General information | Free PDF manual available from IBM for installation, configuration, and troubleshooting |
Frequently Asked Questions - Flex System x222 IBM
How do I install the Flex System x222 into the chassis?
Slide the node into an available half-width slot in the Flex System chassis until it locks into place, then connect the management and data cables as needed.
What processors are supported on each node?
Each node supports one Intel Xeon E5-2600 v2 series processor (two sockets per node). Check the server documentation for the exact list.
Can I operate the two nodes independently?
Yes, each node acts as a separate server with its own processors, memory, storage, and network connections.
How do I manage the Flex System x222 remotely?
Use the Integrated Management Module II (IMM2) via a dedicated management port or the chassis management interface for remote monitoring and control.
What is the maximum memory capacity per node?
Up to 384 GB using 12 registered DDR3 DIMMs (32 GB each) per node.
How many hot-swap drives can I install per node?
Each node supports up to two 2.5-inch hot-swappable SATA or SAS drives.
What operating systems are supported?
Support includes major Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, and VMware ESXi versions. Always check the compatibility matrix.
How do I troubleshoot a node that fails to boot?
Check the node status via IMM2 event logs, verify external dependencies such as memory and power connectors, and reseat or replace failed components.
Can I update firmware safely?
Use the IBM ToolsCenter or UpdateXpress to apply firmware updates while the system is offline or via remote management, following the documented procedures.
What safety precautions should I follow?
Always disconnect the chassis from power before removing or installing the node, wear an antistatic strap, and do not block airflow vents.
User questions about Flex System x222 IBM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual Flex System x222 - IBM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Flex System x222 by IBM.