SRD-842 - Security Camera Hanwha - Free user manual and instructions
Find the device manual for free SRD-842 Hanwha in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Security Camera |
| Brand | Hanwha |
| Model | SRD-842 |
| Resolution | 2 Megapixels (1920x1080) |
| Lens Type | Fixed Focal Lens |
| Focal Length | 3.6 mm |
| Field of View | 90 degrees |
| Night Vision | IR LEDs up to 30 meters |
| Connectivity | Ethernet (PoE) |
| Power Supply | DC 12V or PoE |
| Operating Temperature | -10°C to 50°C |
| Ingress Protection | IP66 |
| Housing Material | Aluminum |
| Dimensions | 70 x 70 x 160 mm |
| Weight | 500 g |
| Storage | MicroSD Card Slot |
| Motion Detection | Yes |
| Two-way Audio | No |
| Maintenance | Clean lens with soft dry cloth |
| Security | WPA2 encryption support |
| Spare Parts | Contact authorized service center |
| General Information | Manual includes setup guide |
Frequently Asked Questions - SRD-842 Hanwha
How do I connect the Hanwha SRD-842 to my network?
Use an Ethernet cable to connect the camera to a router or switch. The camera supports Power over Ethernet (PoE), so if your switch is PoE-enabled, no extra power cable is needed. Otherwise, connect the included power adapter.
How can I access the camera remotely from my smartphone?
Install the official Hanwha mobile app and scan the camera's QR code. Ensure the camera is connected to the internet and port forwarding is configured on your router for remote access.
How do I reset the SRD-842 to factory settings?
Press and hold the reset button located on the camera for about 10 seconds using a pin. The camera will restart and restore all settings to default values.
How to enable motion detection on this camera?
Open the camera's web interface, go to Settings > Detection, and check the Motion Detection option. You can set sensitivity and define detection areas by drawing rectangles on the preview.
Where is the microSD card slot and how do I insert a card?
The microSD slot is inside the camera housing under the cover. Loosen the screws, remove the cover, and insert a microSD card until it clicks. The camera supports cards up to 128GB.
What is the default IP address and login credentials?
The default IP address is 192.168.1.100 with subnet mask 255.255.255.0. The default username is "admin" and password is "1234". Change them immediately after login.
How to update the firmware of the SRD-842?
Download the latest firmware from the Hanwha website, log into the camera's web interface, and go to Maintenance > Upgrade. Select the firmware file and click upgrade. Do not power off during firmware update.
How to configure night vision settings?
The camera automatically switches to B/W mode in low light and activates IR LEDs. To adjust, go to Settings > Video, and enable Smart IR to prevent overexposure.
How should I clean the camera lens?
Use a soft, dry microfiber cloth to gently wipe the lens. Do not use abrasive cleaners. If fingerprints remain, slightly moisten the cloth with a lens cleaning solution and wipe carefully.
What should I do if the camera loses connection frequently?
Check the Ethernet cable connection and ensure the PoE switch provides sufficient power. Also verify that the IP address is not conflicting with another device, and consider enabling DHCP or setting a static IP.
User questions about SRD-842 Hanwha
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Security Camera in PDF format for free! Find your manual SRD-842 - Hanwha and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SRD-842 by Hanwha.
USER MANUAL SRD-842 Hanwha
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hanwha
Model : SRD-842
Category : Security Camera