HL2 LIFTER FOR A20 AMPLIFIER - Helmet accessory PLANTRONICS - Free user manual and instructions

USER MANUAL HL2 LIFTER FOR A20 AMPLIFIER PLANTRONICS

Interface Business Park

Bincknoll Lane

Wootton Bassett

Wiltshire

SN4 8QQ

ENGLAND

Tel: [phone]

Fax: [phone]

Plantronics Denmark

Andersen Nexø Vej 29

2860 Søborg

Denmark

Tel: [phone]

Fax: [phone]

Plantronics B.V.

Antareslaan 9

2132 JE Hoofddorp

The Netherlands

Tel: [phone]

Fax:[phone]

Plantronics France

Plantronics Nordic Region

Oskarsvagen 10

S-702 14 Örebro

Sweden

Tel: [phone]

Fax: [phone]

Plantronics Acoustics Italia SrL

Palazzo G/2, Via Roma 108

20060 Cassina de Pecchi MI

Tel: [phone]

Fax: [phone]

Plantronics Spain

Europa Empresarial

262 Regents Park Road

Finchley

London N3 3HN

Tel: [phone]

Fax: [phone]

Plantronics Ltd, Interface Business Park, Bincknoll Lane, Wootton Bassett, Wiltshire SN4 8QQ. ENGLAND

www.plantronics.com

PLANTRONICS

World Leader in Communications Headsets

HL2 TELEPHONE HANDSET

LIFTER SYSTEM FOR

A20 AMPLIFIER

User Guide

Brugsanvisning

Gebruiksaanwijizing

Käyttoopas

5 A20 Adapter Housing

A20 Adapter kasse

A20 adapterbehuzing

A20 adapterin kotelo

6 On line Indicator Port

On Line indicator indgang

7 Lifting Arm Height Dial

Hjul for loftearmhoyde

The HL2 telephone handset lifter system is a mechanical handset lifter designed for use with the A20 telephone headset amplifier and accessory deck

PUTTING THE HL2 TOGETHER

Remove the parts of the HL2 from their packaging. Place the Accessory Deck (13) of the A20 Amplifier into the Lifter Motor (2). These parts lock together easily.

Remove the Accessory Deck Cover (23) from the Accessory Deck (13) of the A20 Adapter.

If you have already assembled your A20 Amplifier, disconnect the On Line Indicator (OLI) (15) from the Accessory Port (19) of the A20.

Connect the HL2 Cable (1) to the Accessory Port on the base of the A20 (19). Feed the cable through the guide channels in the base of the A20.

Connect the On Line Indicator (OLI) (15) to the On line Indicator Port (6) at the rear of the HL2 lifter. Replace the accessory deck cover (23).

Lift your telephone, and position squarely on the Accessory Deck (13). The base opens out to accommodate larger telephones. (See diagram D in A20 user guide.)

Once your telephone is in position on the Accessory Deck (13), slide the Lifter Arm (3) into the Lifter Arm Holder (4) on the HL2 Lifter Motor. The Lifter Arm needs to be positioned so that it will sit in the cavity under the telephone handset. To tighten the Lifter Arm once it is in the correct position, use a coin to rotate the Lifter Arm Screw (see diagram C).

Next, hold the Lifter Arm and either raise or lower it manually to fit under your handset while it is in its cradle. The arm needs to be underneath the handset in order to raise it and answer the phone. You will encounter some resistance to moving the Lifter Arm, however, you cannot damage the device by making this adjustment.

No other connections are required. The HL2 is powered by the A20 Base Unit.

(Number in black) denote the key from the A20 Amplifier user guide.

FINAL ADJUSTMENTS

In order to make sure that the Lifter Arm is set at the correct height for answering your telephone, press the Handset/Headset Selector (7) on the A20 base unit. Pressing this button then activates the Lifter Arm, which will move upwards, raising the telephone handset as it does so. As the handset is lifted, a dial tone will be heard in your headset receiver. The phone is then ready for you to make a call.

If the lifter arm does not raise the handset far enough to activate the dial tone, simply adjust the rotation of the Lifter Arm using the Lifting Arm Height Dial (7) on the back of the HL2 Lifter Motor Assembly (see diagram D). By moving this dial further towards Hi, the Lifter Arm will lift the handset further from its cradle when activated. The opposite happens if the dial is turned towards Low. Repeat this process until the Lifter Arm is correctly positioned to raise your handset.

Using the HL2 telephone handset lifter system

MAKING A CALL

To make a call, press the Handset/Headset Selector (7) on the A20 base unit. This will activate the Lifter Arm, which lifts the telephone handset from its cradle. You will then hear a dial tone in your headset receiver. Dial your number to make your call.

Once you have finished your call, press the Handset/Headset Selector (7) on the A20 base unit again to replace the telephone handset on its cradle, ready for the next call.

TAKING A CALL

When your phone rings, press the Handset/Headset Selector (7) on the A20 base unit. This will activate the Lifter Arm and route the call to your headset.

Once you have finished your call, press the Handset/Headset Selector (7) on the A20 base unit again to replace the telephone handset on its cradle, ready for the next call.

(Number in black) denote the key from the A20 Amplifier user guide.

PROBLEM

Lifter does not raise my handset when I press the Headset/Handset Selector

SOLUTION

Check that all cables are firmly plugged in.

SOLUTION

Make sure that the Lifter Arm is correctly positioned to enable the handset to be lifted from its cradle.

If necessary, adjust the Lifter Arm using the Lifter Arm Screw and Lifter Arm Height Dial.

IMPORTANT INFORMATION

The intended purpose of the HL2 telephone handset lifter system is to lift and lower the handset of a telephone in conjunction with the A20 Amplifier. The HL2 should not be used for any other purpose.

To ensure safe operation, install, adjust and operate the HL2 as indicated in these instructions.

Keep fingers and other objects clear of the operating arm.

Do not open the case of the Lifter Motor. It requires no maintenance and contains no user serviceable parts.

The HL2 telephone handset lifter system has a 2 year warranty. For year of manufacture please refer to the HL2 base label.

For service please contact your supplier or one of the Plantronics offices shown on the back of this user guide.