SD884S2 - Installation guide AEG - Free user manual and instructions
Find the device manual for free SD884S2 AEG in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Heat pump tumble dryer |
| Brand | AEG |
| Model | SD884S2 |
| Energy efficiency class | A++ |
| Capacity | 8 kg |
| Drying system | Heat pump |
| Dimensions (H x W x D) | 850 x 600 x 660 mm |
| Weight | 52 kg |
| Power supply | 230 V, 50 Hz |
| Power consumption | 2.1 kWh per cycle |
| Noise level | 65 dB(A) |
| Number of drying programs | 12 |
| Display | LED display |
| Door type | Reversible door |
| Sensor drying | Yes |
| Delay start | Up to 20 hours |
| Reverse action | Yes |
| Fluff filter | Located in door, easy to clean |
| Condenser cleaning | Condenser with cleaning indicator |
| Child lock | Yes |
| Spare parts availability | Up to 10 years |
| Warranty | 2 years |
Frequently Asked Questions - SD884S2 AEG
How do I install the AEG SD884S2 tumble dryer?
The installation guide recommends leaving at least 10 cm of clearance around the dryer for ventilation. The dryer must be positioned on a stable, level surface. If you are stacking it on a washing machine, use the appropriate stacking kit. Ensure the water drain hose is correctly connected.
Can the dryer be built under a counter?
Yes, the dryer can be installed under a worktop with a height of at least 85 cm. Make sure the door can be fully opened and the ventilation grilles are not blocked.
How do I reverse the door?
The door hinge can be moved to the opposite side. This operation requires a screwdriver. Follow the instructions on page 6 of the manual. You may need to remove the door and relocate the hinge brackets. It is also possible to contact the AEG service for assistance.
What are the electrical requirements?
The dryer is designed for 230 V single-phase power supply with a 50 Hz frequency. The power cord is equipped with a plug that must be connected to a properly earthed socket. Do not use an extension lead or adaptor.
How do I connect the drain hose?
If you are using the water container, place it securely in the top of the dryer. For direct drainage, connect the supplied hose to the connection on the back and route it to a drain. Ensure the hose is not kinked and that the drainage point is below the dryer's outlet.
How often should I clean the condenser?
The condenser should be cleaned every 6 months or when the indicator on the control panel lights up. Switch off the dryer, open the lower flap, pull out the condenser and rinse it with water until clean. Let it dry thoroughly before reinserting.
Why is the drying cycle taking too long?
Check if the fluff filter is clogged, the condenser needs cleaning, or if the room temperature is too low. Also, the dryer may be overloaded. Make sure you are using the correct program for the fabric type.
How do I reset the dryer?
To reset the dryer, switch it off and unplug it for 10 minutes. Then plug it in and select a new program. If the problem persists, contact the customer service.
How do I activate or deactivate the child lock?
Press and hold the Child Lock button for 3 seconds. The indicator light will show when activated. To deactivate, repeat the same procedure.
Where can I find spare parts?
AEG offers spare parts for up to 10 years after purchase. You can order them from the AEG website or through authorised service centres. Use the model number SD884S2 to identify compatible parts.
User questions about SD884S2 AEG
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Installation guide in PDF format for free! Find your manual SD884S2 - AEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SD884S2 by AEG.
USER MANUAL SD884S2 AEG
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : AEG
Model : SD884S2
Category : Installation guide