DMS-3130-30TS - Network switch D-LINK - Free user manual and instructions
Find the device manual for free DMS-3130-30TS D-LINK in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed L2/L3 Gigabit Ethernet Switch with 10G Uplinks |
| Ports | 24 x 10/100/1000 RJ45 + 4 x 10GBASE-X SFP+ (dedicated) + 2 x 10GBASE-X SFP+ (shared with last 2 RJ45 ports) |
| Dimensions (W x D x H) | 440 x 250 x 44 mm (19-inch rack-mountable, 1U) |
| Weight | 3.5 kg |
| Power Supply | 100-240 V AC, 50-60 Hz, internal; Max. power consumption 45 W |
| Main Functions | Layer 2 switching (VLAN, STP, IGMP snooping) and Layer 3 routing (static, RIP, OSPF); QoS; ACL; SNMP; CLI and Web management; 802.1X; LLDP |
| Cooling | Built-in fan; airflow from front to side |
| Cleaning | Use a soft, dry cloth for the exterior. Do not use liquids or sprays |
| Safety | CE, FCC Class A; UL/CSA; RoHS compliant |
| Spare Parts / Repairability | No user-serviceable parts. Contact D-Link support or authorized service center for repairs |
| General Information | D-Link DMS-3130-30TS; Free user manual available online; 700 pages English version |
Frequently Asked Questions - DMS-3130-30TS D-LINK
How to reset the D-Link DMS-3130-30TS to factory defaults?
Press and hold the Reset button on the front panel for 10 seconds using a paperclip. The switch will reboot with factory settings.
What is the default IP address of the switch?
The default IP address is 10.90.90.90 with subnet mask 255.0.0.0. You can access the web interface via http://10.90.90.90.
How to update the firmware?
Download the latest firmware from D-Link support page. Go to System > Firmware Upgrade in the web interface, select the file, and apply. Do not power off during update.
Does this switch support VLAN tagging?
Yes, it supports IEEE 802.1Q VLAN tagging. You can create up to 4094 VLANs and assign ports with tagged or untagged membership.
Can I use SFP+ modules from other brands?
D-Link recommends using D-Link original transceivers for best compatibility. Third-party modules may work but are not officially supported.
How to enable port mirroring?
Navigate to Monitoring > Port Mirroring. Select the source port and destination port (monitor port). Configure direction (RX/TX/Both) and apply.
What is the maximum power consumption?
The maximum power consumption is 45 watts. Actual consumption depends on port usage and module type.
How to configure link aggregation (LACP)?
Go to Port Configuration > Link Aggregation. Create a trunk group, select member ports (up to 8), enable LACP (active/passive), and apply.
The switch is overheating. What should I do?
Ensure the switch is in a well-ventilated area. Check that the fan is working. Clean the air vents with compressed air. If overheating persists, reduce load or contact support.
How to access the command-line interface (CLI)?
Connect a console cable to the Console port (RJ45) and use a terminal emulator (e.g., PuTTY) with settings: 115200 baud, 8 data bits, 1 stop bit, no parity, no flow control.
User questions about DMS-3130-30TS D-LINK
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Network switch in PDF format for free! Find your manual DMS-3130-30TS - D-LINK and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DMS-3130-30TS by D-LINK.
USER MANUAL DMS-3130-30TS D-LINK
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : D-LINK
Model : DMS-3130-30TS
Category : Network switch