MMX-4X4CAT-150M - Router KanexPro - Free user manual and instructions
Find the device manual for free MMX-4X4CAT-150M KanexPro in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | HDMI Matrix Switch over CAT (Router) |
| Model | MMX-4X4CAT-150M |
| Brand | KanexPro |
| Input Ports | 4 HDMI inputs |
| Output Ports | 4 CAT5e/6 outputs (up to 150m) |
| Max Resolution | 1080p@60Hz (may support 4K30) |
| Control Interface | IR remote, RS232, front panel buttons |
| Power Supply | DC 12V 2A (included) |
| Dimensions (W x D x H) | 440 x 150 x 44 mm (1U rackmount) |
| Weight | 2.0 kg |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| HDCP Support | Yes, HDCP 1.4 |
| EDID Management | Internal EDID emulation |
| Signal Extension | Up to 150m over CAT6 at 1080p |
| Maintenance | Keep vents clean; avoid moisture |
| Safety | Use included power adapter; do not open casing |
| Spare Parts | Power supply, IR remote, rack ears |
| Repairability | Not user-serviceable; contact support |
| General Information | Designed for AV distribution in commercial settings |
Frequently Asked Questions - MMX-4X4CAT-150M KanexPro
How do I connect the MMX-4X4CAT-150M to my sources and displays?
Connect up to 4 HDMI sources to the input ports. Use CAT5e/6 cables from the output ports to receivers (sold separately) near displays. Ensure all devices are powered off before connecting.
What is the maximum supported resolution?
The matrix supports up to 1080p@60Hz. Some units may support 4K@30Hz; check the manual for specifics. For best performance, use high-quality HDMI and CAT cables.
How do I switch between sources?
Use the front panel buttons to select input per output. You can also use the included IR remote or RS232 commands. The unit remembers the last routing.
Can I control the matrix via RS232?
Yes. Connect a computer or control system to the RS232 port. Use 9600 baud, 8 data bits, no parity, 1 stop bit. Refer to the manual for command list.
Why is there no signal on my display?
Check that the HDMI source is powered on and outputting. Verify the CAT cable is properly terminated and within 150m. Ensure the receiver (if used) is powered and connected. Try pressing the EDID reset button.
Does the unit support HDCP?
Yes, it supports HDCP 1.4. Protected content will pass through. For HDCP 2.2 sources, you may need a separate converter.
How do I perform a factory reset?
Press and hold the Menu button on the front panel for 10 seconds until all LEDs blink. Alternatively, send a factory reset command via RS232.
What type of CAT cable should I use?
Use shielded CAT6 or better for optimal performance. Unshielded may work but can cause interference. Ensure the cable is not damaged and meets TIA/EIA standards.
Can I extend the signal beyond 150 meters?
The maximum rated distance is 150m at 1080p. For longer distances, use a signal booster or switch to a different transmission method. Exceeding the limit may result in signal loss.
How do I update the firmware?
Firmware updates are not typically user-accessible. Contact KanexPro support for availability. If an update is needed, you may need a special programmer.
User questions about MMX-4X4CAT-150M KanexPro
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Router in PDF format for free! Find your manual MMX-4X4CAT-150M - KanexPro and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MMX-4X4CAT-150M by KanexPro.
USER MANUAL MMX-4X4CAT-150M KanexPro
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : KanexPro
Model : MMX-4X4CAT-150M
Category : Router